Jahutid ja lisad

The EK-Quantum Momentum Aorus Z490 Master D-RGB is the new Quantum Line monoblock designed specifically for the Gigabyte Aorus Z490 master motherboard. The top side of the monoblock is made of acrylic glass and the integrated addressable D-RGB lighting sets the block perfectly in scene. Based on the EK Momentum series, the CPU cooler has been further optimised in terms of performance and optimum coolant flow. The cooling plate is made of nickel-plated copper and impresses with its dense micro-rib structure. Thanks to the pre-installed nickel-plated brass screw-in spacers, installation is made easy. The supplied thermal pad is used on voltage regulator modules to improve stability and performance and extend the life of the motherboard. The block is equipped with a 3-pin 5V addressable D-RGB LED strip compatible with the 3-pin 5V D_LED (addressable LED strip) headers of the Aorus Z490 Master. This product is also compatible with D-RGB controllers that support the pin assignment: +5V, D, Blocked, Ground. The arrow marking on the 3-pin LED connector must be aligned with the +5V marking on the D_LED (addressable LED strips). Technical Data D-RGB-Anschluss 3-polige 5V-Digital-LED-Stiftleiste (Pinbelegung: +5V, D, blockiert, Masse) Enclosed: EK-Quantum Momentum Aorus Z490 Master D-RGB Monoblock Mounting mechanism Thermal grease EK-TIM Ectotherm Thermal pads

EK-Quantum Vector N+ RX 6800XT/6900XT is a 2nd generation Vector GPU water block from the EK® Quantum Line. It is made for SAPPHIRE NITRO+ 6800XT and 6900XT graphics cards based on the latest AMD® RDNA2™ architecture. EK-Quantum Vector N+ RX 6800XT/6900XT water block for SAPPHIRE NITRO+ GAMING RX 6800 XT and 6900 XT GPUs EK-Quantum Vector N+ RX 6800XT/6900XT water block is compatible with SAPPHIRE NITRO+ Radeon, RX 6800XT, and 6900XT graphics cards. The Vector water block directly cools the GPU, VRAM, and the VRM (voltage regulation module) as a cooling liquid is channeled right over these critical areas. The water block is in contact with power stages as well as Inductor chokes to maximize cooling and minimize the chances of coil whine. These newly developed water blocks feature optimized flow paths that reduce hydrodynamic instabilities and vortexing (dead spots) inside of them. The EK-Quantum Vector Series water blocks use an Open Split-Flow cooling engine design, which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, meaning it can be used with weaker water pumps or pumps running on low-speed settings, and still achieve top performance. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performance when used in any given coolant flow orientation. The base of the block is CNC-machined out of high-grade nickel-plated electrolytic copper, while its top is CNC-machined out of glass-like cast Acrylic. These 2nd generation Vector GPU water blocks also feature acetal terminals. The watertight sealing is ensured by high-quality EPDM O-rings, while brass standoffs are already pre-installed and allow for a safe and easy installation procedure. D-RGB lighting on EK-Quantum N+ Vector RX 6800XT/6900XT D-RGB water block The aesthetic end-piece is housing the addressable D-RGB LED strip. These water blocks boast a total of 8 individually addressable RGB LEDs, and a LED-lit terminal. They are compatible with popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 3-pin D-RGB LED connector is to be aligned with the +5V marking on the D-RGB (addressable) header. Backplate for the N+ 6800XT/6900XT water block EK recommends the purchase of a retention backplate, which improves the overall aesthetics of your graphics cards, and also provides additional passive cooling for the GPU core and backside of the printed circuit board VRM and VRAM sections. Technical Specification Dimensions: (LxHxW) - 285x149x16.5mm Enclosed EK-Quantum Vector N+ RX 6800XT/6900XT series high-performance water block Mounting mechanism with screw-in brass standoffs Necessary mounting screws, nuts, and washers 2x Nickel plated brass plug G1/4” EK-Loop Multi Allen Key (6mm, 8mm, 9mm) Thermal pads Thermal grease EK-TIM Ectotherm (1g)

EK-Quantum Vector TUF RX 6800/6900 is a 2nd generation Vector GPU water block from the EK® Quantum Line. It is made for ASUS TUF RX 6800, 6800XT, 6900XT graphics cards based on the latest AMD® RDNA2™ architecture. EK-Quantum Vector TUF RX 6800/6900 water block for ASUS TUF GAMING RX 6800 and 6900 GPUs EK-Quantum Vector RX 6800/6900 water block is compatible with ASUS TUF GAMING Radeon RX 6800, RX 6800XT, and 6900XT graphics cards. The Vector water block directly cools the GPU, VRAM, and the VRM (voltage regulation module) as a cooling liquid is channeled right over these critical areas. The water block is in contact with power stages as well as Inductor chokes to maximize cooling and minimize the chances of coil whine. These newly developed water blocks feature optimized flow paths that reduce hydrodynamic instabilities and vortexing (dead spots) inside of them. The EK-Quantum Vector Series water blocks use an Open Split-Flow cooling engine design, which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, meaning it can be used with weaker water pumps or pumps running on low-speed settings, and still achieve top performance. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performance when used in any given coolant flow orientation. The base of the block is CNC-machined out of high-grade nickel-plated electrolytic copper, while its top is CNC-machined out of durable POM acetal. These 2nd generation Vector GPU water blocks also feature acetal terminals. The watertight sealing is ensured by high-quality EPDM O-rings, while brass standoffs are already pre-installed and allow for a safe and easy installation procedure. D-RGB lighting on EK-Quantum TUF Vector RX 6800/6900 D-RGB water block The aesthetic end-piece is housing the addressable D-RGB LED strip. These water blocks boast a total of 9 individually addressable RGB LEDs, and a LED-lit terminal. They are compatible with popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 3-pin D-RGB LED connector is to be aligned with the +5V marking on the D-RGB (addressable) header. Backplate for the TUF 6800/6900 water block EK recommends the purchase of a retention backplate, which improves the overall aesthetics of your graphics cards, and also provides additional passive cooling for the GPU core and backside of the printed circuit board VRM and VRAM sections. Technical Specification Dimensions: (LxHxW) - 300x158x16.5mm Enclosed EK-Quantum Vector TUF RX 6800/6900 series high-performance water block Mounting mechanism with screw-in brass standoffs Necessary mounting screws, nuts, and washers 2x Nickel plated brass plug G1/4” EK-Loop Multi Allen Key (6mm, 8mm, 9mm) Thermal pads Thermal grease EK-TIM Ectotherm (1g)

With the Core Ocean AiO, Alphacool presents an all-in-one solution that, thanks to its excellent price-performance ratio, enables entry into performance-oriented CPU water cooling. The difference to the Eisbaer CPU AiO is that the Ocean All-in-One is not expandable. Adding further components such as GPU coolers, radiators or expansion tanks is not intended here. But also not necessary! The choice of components and the design of the Core Ocean enable a long service life with low maintenance for water cooling of all common mainstream sockets from AMD and Intel. Aluminium Radiator Compared to Alphacool's full copper models, the T38 aluminium radiator has additional cooling channels. This technical design allows a significant increase in cooling capacity without restricting the water flow within the radiator. Due to the low height of 38mm, the radiator with single-sided fan assembly fits into the tightest case and enables high-performance water cooling of the CPU. Core fan The fan can be regulated from 0 to 2500 rpm via the 4-pin PWM connection. The cable is 40cm long. This allows the fan to be connected to the mainboard or a special controller without the need for additional adapter cables or extensions. At 2500 rpm, it provides an air flow of 62.8 CFM, together with a high static pressure of 2.13mm/H2O. This makes the fan perfect for mounting on radiators of a water cooling system. Cooler & Pump As with all Alphacool products, the radiator base is made of copper and is equipped with very fine cooling fins distributed over the entire base. A nozzle plate ensures an accelerated flow over the cooling fins, which increases the cooling performance. The water flow is optimised so that all areas of the cooler base are cooled evenly. The cooler is compatible with all common mainstream sockets from AMD and Intel. The built-in pump has a speed range of 2500 - 3500 RPM (+/- 10%) and can be controlled via PWM. The pump is connected to the mainboard or to an external controller via the existing 4-pin fan connector. This allows the speed range of the pump to be controlled and monitored. Hoses & Connections The FEP hoses are 40cm long, sleeved and very flexible. The rotatable 360° connections to the cooler and to the radiator are permanently installed and cannot be replaced. However, the combination of hoses and connectors allows a very variable positioning of the AiO even in the tightest PC case. Illumination 12 digitally addressable 5V RGB LEDs are installed in the pump housing, which create a unique, very noble-looking illumination. The digital aRGB LED lighting is connected via a JST 3-pin connector. To control the lighting, the 3-pin female connector must be connected to a digital RGB controller (not included) or a digital RGB-capable mainboard. Additional digital RGB LEDs can be connected to the remaining 3-pin male connector. Thermal compound The thermal paste included in the delivery has a thermal conductivity of 7.5 W/mK. The thermal grease does not harden, is particularly suitable for high contact pressures and can be applied perfectly due to the optimally selected viscosity.   Compatibility: Intel: LGA 115x / LGA 1200 / LGA 1700 / LGA 2066 AMD: AM4 / AM5   Technical data radiator L x W x H 279 x 120 x 38mm Material cooling fins, channels & prechamber 3003 Aluminium Material outer housing & threads 3003 Aluminium Fins per Inch 19 Fan size 120mm Fan slots 2 one-sided / 4 double-sided Color black Technical data fans L x W x H 120 x 120 x 25mm Bearing Type hydraulic Bearing Rated Voltage DC 12V Operating Voltage DC 7-14V Start-up Voltage 7V Rated Current 0.23 (Max. 0.4) A Rated Power 2.76 (Max. 4.8) W Rated Speed 0 - 2500rpm/min (±10%) Max. Air Flow 62.8CFM Max.Static Pressure 2.13mm-H2O Noise level (rated voltage, mute room, distance 1m) 33.0 (Max. 34.3) dBA MTBF 50000hrs at 25°C Speed Control Mode PWM Connection & control 4-pin PWM (cable 40cm) Auto-Restart yes Tachometer Output yes Color black Technical data cooler & pump L x W x H 70,2 x 70,2 x 46mm Material cooler bottom copper Material pump housing Synthetic material (ABS+PC) Fin structure cooler bottom 0,1 x 0,1mm Material pump bearing & shaft ceramics Starting voltage > DC 6V Rated power 7.1W Noise level 35Db Rated Current 0.59A (±10% MAX) Speed 2500~3500 (±10% RPM) Power supply Digital aRGB 3-pin 5V (male & female, cable length 30cm) Number of aRGB LEDs 12 Power supply pump 4-Pin JST (Kabellänge 30cm) Technical data tubes Material FEP, black with weave cover Length 400mm

Termopasta ArcticSilver AS-5 ,99% hõbedasisaldus, 3,5 g

The ARCTIC MX-4 is a new thermal compound that guarantees exceptional heat dissipation from components and maintains the needed stability to push your computer system to its maximum. The ARCTIC MX-4 continues to be overclocker’s ultimate choice when choosing thermal compound.Exceptional performanceThe ARCTIC MX-4 is composed of carbon micro-particles that lead to an extremely high thermal conductivity. It guarantees quick and efficient dissipation of heat from the CPU or GPU.Safe and easy applicationThe ARCTIC MX-4 is a metal-free and non-electrically conductive compound.That eliminates the risks of short circuit and provides protection to your computer. Also the application is very easy as the consistency is just ideal for application on chips.Great valueWith the competitive pricing of the ARCTIC MX-4, the performance of the ARCTIC MX-4 is the best thermal compound on the market.Content 4 gramme

Efficient Thermal ConductivityThe Thermal Pad based on silicone and a special filler outperforms generic and performance pads by far.Filling the GapsDue to its low hardness and great compressibility, the thermal pad works as the perfect gap filler and bridges uneven surface and gaps without any problems.Easy to ApplyInstalling the ARCTIC Thermal Pad is child's play; perfect for beginners..Safe HandlingThe Pad does not contain any metallic particles, is electrically isolating and not capacitive. The handling is safe as contact with any electrical traces would not result in damage of any sort.Toote värvSinineMaterjalSilikoonPakendi laius195 mmPakendi kõrgus210 mmPakendi kaal45 gLaius145 mmSügavus0,5 mmKõrgus145 mmKaal41 g

Accessories NANO GREASE 3G

X-Shotz by X-Gamer , an isotonic drink! 10g concentrated drink powder exclusively designed for e-sports, semi-pros and enthusiasts to boost performance and make the senses sharper and faster. Consists of glucose, taurine, caffeine, many vitamins and maltodextrose, among others, with only 31 kilocalories per 500ml and excellent taste. Unlike other isotonic beverage powders, this product contains little sugar. The preparation is very simple: mix 10g (two measuring spoons) with water, 350ml to 500ml, shake well for 20 seconds and off you go! Please note: The recommended amount (10g or two measuring spoons) must not be exceeded! Contains sugar, sweeteners and caffeine (200 mg caffeine per daily dose). Not recommended for children and pregnant or nursing women. E104, E110, E129 and E102 may impair activity and attention in children. Furthermore, dietary supplements are not a substitute for a balanced and varied diet and a healthy lifestyle. Store dry, at room temperature and out of the reach of children. Avoid direct sunlight. Consume within 6 months of opening. Ingredients: Taurine, caffeine, dextrose, vitamin and mineral complex, maltodextrin, acidifiers (malic acid, citric acid, ascorbic acid), aromas, colourings (E133, E162, E163, E129, E102, E104, E160a, E150a), sweeteners (sucralose), L-carnitine, L-tyrosine. May contain traces of eggs, peanuts, gluten, nuts and soya. Food supplements with taurine, caffeine, vitamins & minerals. Niacin, pantothenic acid, riboflavin and vitamin B6 contribute to a normal energy metabolism, as well as to a reduction of fatigue and fatigue. Pantothenic acid contributes to normal mental performance. Nutritional information 2 dosage spoons / per 100G Energy: 129 kJ/31 kcal / 1290 kJ/310 kcal grease: 0.02g / 0.2g of which saturated fatty acids: 0g / 0g Carbohydrates: 3g / 30g of which sugar: 0.2g / 2g Protein: 0.7g / 7g salt: 0g / 0g Nutrients 2 dosage spoons / % NRV* Taurine: 1g / ** Caffeine: 200mg / ** Niacin: 31.2mg / 195% vitamin E: 3.2mg / 26.7% thiamine: 0.6mg / 54.5% riboflavin: 0.6mg / 42.9% vitamin B6: 0.6µg / 42.9% vitamin B12: 6.8µg / 272% biotin: 8µg / 16% pantothenic acid: 2.4mg / 40% Chromium: 4.4µg / 11% boron: 22µg / ** Lutein: 12µg / ** * Nutrient reference values according to EU Regulation 1169/2011 ** - no nutrient reference values available General product information Weight: 0,0142 kg Filling quantity: 10g Brand: X-Gamer Taste: Hyperbeast, Fruit

Compact alumnium cooler with PWM fan for mini-ITX system based on AMD platformUltra compact and quiet cooler for low power AMD CPU’s. The low profile design with total height of 29mm makes it a perfect solution for mini-ITX, HTPC and SFF systems.Aluminium heatsink with quiet EBR bearing fan ensure high efficiency and long life. Multi directional aluminium heatsink maximizes heat dissipation. PWM fan ensures optimal CPU, motherboard and VRM cooling with minimal noise levels.Cam lever clip ensures easy installation, reliable retention and maximum compatibility on AMD platforms. Pre-applied high performance thermal compound ensures clean and easy installation.- Multi-directional fins for maximum system cooling- Low noise 8cm fan with PWM control- Cam-lever clip for easy and reliable installation- High performance thermal interface is pre-applied- Total height of 29mm - ideal for ITX systemsSobilikProtsessorTüüpJahutiVentilaatori läbimõõt8 cmToetatud protsessoripesadPistikupesa 754, Pistikupesa 939Müratase (suur kiirus)21 dBToote värvMustMaterjalAlumiiniumNimivool0,25 AKaal182 gMõõdud (l x s x k)80 x 80 x 29 mmToitenõuded12V DCPistmik(ud)4pin PWMPöörlemiskiirus600 RPMToote tööiga40000 hÕhuvool22.44 CFM

SilverStone Technology’s Nitrogon NT07-115X is a super slim profile CPU cooler designed for space limited applications that utilizes LGA 1156, 1155, or 1150 platforms. It has a copper center construction with extruded aluminum fins for excellent thermal conductive capability that rivals many larger coolers. The custom 80mm PWM fan was designed with fan blades to achieve the highest air pressure possible while maintaining an acoustic profile that is rare for cooler of this size. At a total height of only 23mm tall, the NT07-115X is an essential choice for super slim cases such as SilverStone Petit PT12 or PT13 utilizing LGA 1156, 1155, or 1150 processors.- Support Intel LGA1156/1155/1150 processors- Designed for low profile systems at only 23mm tall- Large, custom 80mm PWM fan for excellent cooling and low noise- Copper center and base with extruded aluminum fins- Easy to installAttachment screwedSocketsuitable 1156, 1155, 1150MaterialAluminum YesCooper YesPower Connection PWM fan connectorPower Input 0 - 65 watt(s)Voltage Range 0 - 9 VNumber of Revolutions 2000 - 3600 rpmVolume 21.9 - 34.7 dB(A)Volumetric Flow 26.5 - 47.7 m3/h, 15.6 - 28.1 cfmDimensionsFans Fan 1 80 x 10 x 80 mmCooler 90 x 23 x 90 mmTotal 90 x 23 x 90 mmWeightCooler 201 gramsFeaturesincluding Thermal Paste/Pad YesCooling Performance 65 watt(s)

Deepcool Z10 B

Arctic MX-2 2019 Edition Termopasta - 8g

Average Particle Size: 0,36 micron (70 particles lined up in a row equal 1/1000th of an inch.) Temperature Limits:Peak -150°C to >185°C Long-Term -150°C to 130°C Net Weight:2.7-gram syringe. (Approximately 1cc) At a layer 0.003" thick, one syringe will cover about 22 square inches. More info:http://www.arcticsilver.com/cmq2.html

Thermal conductivity: 8 W/mK Relative density: 2.6 Volume: 1.5 ml

Eeltäidetud, lihtne paigaldada!; 420 mm jahutuselement; AF RGB ELITE fännid; Null RPM režiim; Eelpaigaldatud XTM70 termopasta

120mm cooler for Intel LGA 4677, 2x powerful 120mm fans, ideal for tower cases and dual-CPU setups, pre-applied thermal pasteIntel Xeon LGA3647-0

The cuplex kryos NEXT marks a new milestone in CPU water block development. Every detail has been analyzed, optimized and tested to achieve perfection in cooling performance, installation procedure and product features. The result is not just a CPU water block with outstanding performance - it is a product series with various models differing in color and functionality. The VARIO models are the first CPU water blocks globally to incorporate a real-time adjustable base - never before has it been possible to adjust the geometry of a CPU block to perfectly fit the CPU while the PC is in operation. Models with VISION module are equipped with modern electronics: High resolution OLED display, integrated water temperature sensor and USB interface are just three of the features.Base part with micro structureThe base part of the cuplex kryos NEXT is equipped with an extremely fine micro structure, the structural width is lower than 200 µm. The coolant is injected centrally through a slot-shaped nozzle and then runs to both sides of the structure. The base itself is manufactured from copper, nickel plated copper or .925 sterling silver depending on model.Retention systemThe cuplex kryos NEXT retention system consists of 2.5 mm thick stainless steel plates equipped with nickel plated spring cups. Springs and knurled screws secure the water block on the motherboard, the retention system has a very clean look when installed. All retention system versions feature a mechanical stop for optimum clamping force and even force distribution. The knurled screws can be installed by hand, additionally a hexagon socket wrench can be used for easy installation.Water blocks for socket 115x or AM3 include a steel back plate with silicone insulation to stabilize the CPU region of the motherboard. Socket 2011 or AM4 motherboards already include a back plate as part of the CPU socket, therefore no additional back plate is required.For optimum performance, every cuplex kryos NEXT ships with outstanding thermal compound. A syringe with 0.5 grams of Thermal Grizzly Kryonaut is included, complete with plastic spatula. This compound has a high thermal conductivity and spreads out thin and evenly between CPU and water block due to its low viscosity. The amount is sufficient for approximately five applications.Color variantsThe top part of the water block is available in various materials and coatings:Acetal black: Shiny black high-tech plasticAcrylic glass: Transparent body suitable for illuminationCopper: Reddish glossNickel plated brass: Bright metallic glossPVD plated brass: High quality multi layer coating, dark metallic glossMaterial combinationCopper/copper: Top part copper, base copperTechnical detailsDimensions: Socket AM4: 111 x 75 x 22 mm (not including screws)Connection threads: G1/4Distance between threads: 24 mmScope of delivery Water block Mounting material (screws, springs, etc.) Thermal compound Thermal Grizzly Kryonaut, approx. 0.5 grams in syringe Plastic spatula Instruction manual

With the HEATKILLER® V, Watercool is starting a new generation of coolers for the current Nvidia RTX 30 graphics cards. Equipped with unique highlights, the current version of the HEATKILLER® V presents what is technically feasible. With an increased number of cooling fins, the cooling performance is increased directly above the graphics processor and thus the most important area is improved. The radiator base, milled from a solid block, establishes contact with all relevant components. The trend-setting dual-layer inflow distributes the water simultaneously on two levels. This ensures an air flow that is at least 30 percent higher than that of our previous generation. The broad and symmetrical flow paths reduce dead spots (standing water) to a minimum and accelerate the flow. The overall result increases not only the maximum cooling capacity but also the flow rate of the HEATKILLER® V. Thanks to the newly designed spacers made of high-performance plastic (PEEK), the 10mm solid copper block is ideally isolated from the circuit board. In addition to the technical innovations, the design of the cooler is also impressive. The screwless cover makes the entire block look like it was cast from a single source. The symmetrically designed channels underline the look of the cooler and make it a unique eye-catcher. The integrated aRGB strips are now standard in combination with the nickel-acrylic variants. This means that the HEATKILLER® V can be perfectly integrated into the lighting concept of the computer. Technical specifications: Base plate material: nickel-plated electrolyte copper Material cover: acrylic glass Cover material: annealed stainless steel Connection terminal material: Acetal Dimensions: (LxWxH): 230 x 119 x 21 mm Connection: 4x G ¼ inch (DIN ISO 228-1) Weight: Pressure tested: 2 bar Compatibility: Nvidia Geforce RTX 3080/3090 Scope of delivery: 1x HEATKILLER® V 1x HEATKILLER® LED Strip aRGB 1x mounting material Thermal Grizzly Kryonaut thermal paste

With the HEATKILLER® V, Watercool is starting a new generation of coolers for the current Nvidia RTX 30 graphics cards. Equipped with unique highlights, the current version of the HEATKILLER® V presents what is technically feasible. With an increased number of cooling fins, the cooling performance is increased directly above the graphics processor and thus the most important area is improved. The radiator base, milled from a solid block, establishes contact with all relevant components. The trend-setting dual-layer inflow distributes the water simultaneously on two levels. This ensures an air flow that is at least 30 percent higher than that of our previous generation. The broad and symmetrical flow paths reduce dead spots (standing water) to a minimum and accelerate the flow. The overall result increases not only the maximum cooling capacity but also the flow rate of the HEATKILLER® V. Thanks to the newly designed spacers made of high-performance plastic (PEEK), the 10mm solid copper block is ideally isolated from the circuit board. In addition to the technical innovations, the design of the cooler is also impressive. The screwless cover makes the entire block look like it was cast from a single source. The symmetrically designed channels underline the look of the cooler and make it a unique eye-catcher. Technical specifications: Base plate material: electrolyte copper Material cover: acrylic glass Cover material: black anodized aluminum Connection terminal material: Acetal Dimensions: (LxWxH): 230 x 119 x 21 mm Connection: 4x G ¼ inch (DIN ISO 228-1) Weight: Pressure tested: 2 bar Compatibility: Nvidia Geforce RTX 3080/3090 Scope of delivery: 1x HEATKILLER® V 1x mounting material Thermal Grizzly Kryonaut thermal paste

With the HEATKILLER® V, Watercool is starting a new generation of coolers for the current Nvidia RTX 30 graphics cards. Equipped with unique highlights, the current version of the HEATKILLER® V presents what is technically feasible. With an increased number of cooling fins, the cooling performance is increased directly above the graphics processor and thus the most important area is improved. The radiator base, milled from a solid block, establishes contact with all relevant components. The trend-setting dual-layer inflow distributes the water simultaneously on two levels. This ensures an air flow that is at least 30 percent higher than that of our previous generation. The broad and symmetrical flow paths reduce dead spots (standing water) to a minimum and accelerate the flow. The overall result increases not only the maximum cooling capacity but also the flow rate of the HEATKILLER® V. Thanks to the newly designed spacers made of high-performance plastic (PEEK), the 10mm solid copper block is ideally isolated from the circuit board. In addition to the technical innovations, the design of the cooler is also impressive. The screwless cover makes the entire block look like it was cast from a single source. The symmetrically designed channels underline the look of the cooler and make it a unique eye-catcher. Technical specifications: Base plate material: electrolyte copper Material cover: acrylic glass Cover material: annealed stainless steel Connection terminal material: Acetal Dimensions: (LxWxH): 230 x 119 x 21 mm Connection: 4x G ¼ inch (DIN ISO 228-1) Weight: Pressure tested: 2 bar Compatibility: Nvidia Geforce RTX 3080/3090 Scope of delivery: 1x HEATKILLER® V 1x mounting material Thermal Grizzly Kryonaut thermal paste

The Eisschicht from Alphacool can, like other thermal pads, compensate for the irregularities of heat sinks and the elements to be cooled. But it has a great feature: The Eisschicht consists of thermal paste with an embedded mesh! This ensures that the performance of these pads is much more efficient than normal thermal pads, regardless of the low W/mK value. In addition, a better distribution and filling between the surfaces is achieved. This also results in better air displacement. Due to their soft consistency, there is also no pressure on components or solder joints. Nvidia also uses this kind of pads for the Founders Edition. The Eisschicht can be easily cut to the desired size and attached to heat sinks without slipping.As a basic component or spare part, thermal pads belong in every well-organized computer tinkering corner! Technical dataDimensions (L x W x H)100 x 100 x 1mmThermal conductivity3 W/mKElectrical ConductiveNoColorwhite

The Alphacool Eisschicht Ultra Soft are the ultimate in thermal pads. Their outstanding properties mean they can almost be compared to thermal paste. The Eisschicht Ultra Soft pads fit much better to components, which contributes to excellent cooling performance.Better than standard thermal pads?The ultra-soft material of the Eisschicht Ultra Soft thermal pads acts in a similar way to thermal paste. While normal thermal pads are simply pressed together by the contact pressure, which can lead to uneven contact pressure on components of different heights, this is almost impossible with the Eisschicht Ultra Soft thermal pads. The material spreads as well as thermal paste and thus prevents the highest components from being subjected to increased contact pressure from the cooler. In the worst case, this can lead to the PCB bending. The soft consistency also fills in any uneven areas much better. The Eisschicht Ultra Soft thermal pads therefore cling much better to the components, which of course benefits heat transfer.But that’s not the only advantage!The special material also cannot dry out. Usually the silicone in thermal pads bleeds over time. This causes them to become hard and the performance of the pads drops rapidly at a certain point. This is not the case with the Eisschicht Ultra Soft thermal pads. They can be used for a much longer period of time without losing any significant performance.A thermal pad with fabric?The consistency of the heat-conducting material is similar to a viscous thermal paste. A special fabric is embedded so that the material remains stable and can be used as a thermal pad. This ensures perfect distribution of the material if the element to be cooled has an uneven shape. Examples of this include voltage converters, VRam and similar electronic components of all kinds that require cooling.Cropping? No problem!When cutting the thermal pads, you should definitely leave the foil on the pads. This means that the pads can be easily cut to size with scissors. It's just as easy as cutting paper. The cut edges stay perfectly clean and don't fray.The Alphacool Eisschicht Ultra Soft thermal pads are superior to the usual thermal pads in many ways and are also used in all new Eisblock Aurora graphics card coolers from Alphacool. Technical dataDimensions (L x W x H)100 x 100 x 3mmThermal conductivity3 W/mKElectrical ConductiveNoColorwhite

Product Details: Thermal Grizzly - Basic TG Putty Basic is a non-electrically conductive alternative to traditional thermal pads. This easy-to-apply and flexible material serves as a "gap filler," effectively compensating for height differences. It is an ideal replacement for thermal pads on graphics cards, where different pad thicknesses are typically used. When replacing pads or upgrading to a GPU water block, multiple thermal pad sizes are usually required. TG Putty can be applied using the included spatulas or by hand (gloves recommended). The spatula allows for smooth, even application over larger areas, while alternatively, the putty can be shaped into small beads that precisely fit components such as VRAM or SMDs. TG Putty can compensate for height differences ranging from 0.2 mm to 3.0 mm. Available Variants:TG Putty comes in three versions, each offering different levels of thermal conductivity: TG Putty Basic – Medium thermal conductivity TG Putty Advance – Good thermal conductivity TG Putty Pro – High thermal conductivity For upgrading a smaller graphics card without an active backplate (e.g., GeForce GTX 1060), a single 30g jar of TG Putty is usually sufficient. For larger models, such as the GeForce RTX 4090, one 30g jar typically covers the memory (VRAM) and voltage regulators (VRM) on the front side. Since high-end graphics cards often have a uniform gap between the PCB and the backplate, fully filling this space may require two 30g jars. Important Notes: TG Putty is not suitable for direct application on processors (IHS or Direct Die) or GPU chips. Before applying, ensure that the target surface is thoroughly cleaned and degreased using TG Cleaning Wipes or standard isopropanol. Package Contents: 1x TG Putty Basic 3x Spatulas

Recommended for the following Thermal Grizzly pastes: Aeronaut, Hydronaut, Kryonaut, and Kryonaut Extreme. The Thermal Grizzly Spatula, in its basic version for thermal paste, is an essential tool to ensure precise and even application. These plastic spatulas are soft and have lower hardness compared to metal tools, reducing the risk of scratching or damaging the surface of the CPU or other components where the thermal paste is applied. Plastic spatulas also offer the added benefit of being non-reactive with the metallic components of thermal compounds. Notes: Care should be taken to ensure that the spatula used is clean and free from residues or impurities. Residues on the applicator may affect the results of the application. The spatulas should only be used with thermal paste. The TG Spatula is recommended for Aeronaut, Hydronaut, Kryonaut, and Kryonaut Extreme, and is supplied in a convenient pack of three.

Zalman Alpha2 DS A240 White - All-in-One Liquid Cooling with Innovative DisplayThe Zalman Alpha2 DS A240 White is a high-performance all-in-one liquid cooler that delivers optimal cooling while standing out with its unique design and customization options. Highlights: Monitoring and Style: A 2.73-inch IPS LCD display on the pump provides real-time system temperature monitoring. Customize the display with your own images or videos to give your PC a unique look! Efficient Cooling: Three Zalman AF120 fans with Shark Fin Blades ensure optimized airflow and quiet operation. The 240mm aluminum radiator offers maximum cooling surface for your CPU. Easy Control: Manage fans and RGB lighting easily via the ZM-OZ software and ZM-OZ HUB controller. The Daisy-Chain Cable Connector simplifies clean cable management. Wide Compatibility: Compatible with Intel sockets (LGA 1851 / 1700 / 1200 / 115X) and AMD sockets (AM5 / AM4). Technical Specifications: Pump: Dimensions: 72 x 72 x 65 mm Materials: ABS, PC, Pure Copper Speed: 3,300 RPM ±10% Bearing Type: Ceramic Bearing Water Flow: 1.25 L/min Rated Voltage: 12V (LED: 5V) Power Consumption: 5.4 W Radiator: Dimensions: 120 x 277 x 27 mm Material: Aluminum Fans: Dimensions: 120 x 120 x 25 mm Bearing Type: Hydro Bearing Speed: 600 ~ 2,000 RPM ±10% Maximum Noise Level: 29.7 dB(A) ±10% Maximum Air Pressure: 2.01 mmH₂O ±10% Lifespan: 40,000 hours (~4.5 years continuous operation) Connector Type: 4-pin Control Method: PWM LED: Addressable RGB (3-pin 5V) Rated Voltage: 12V DC (LED: 5V) Power Consumption: 3.36 W (LED: 1.8 W) Thermal Paste: Model: ZM STC-10 The Zalman Alpha2 DS A240 offers powerful and visually stunning all-in-one liquid cooling to keep your system running optimally while allowing full customization.

EK-Pro CPU WB 4189 Rack – Nickel + Acetal Enterprise-Grade CPU Water Block for Intel® LGA 4189 – Rack-Optimized and 1U-Compatible The EK-Pro CPU WB 4189 Rack – Nickel + Acetal is a high-performance CPU water block designed specifically for Intel® LGA 4189 processors, optimized for 1U rack chassis. It’s built to deliver outstanding thermal performance, serviceability, and reliability, making it an ideal choice for enterprise-grade applications in dense server environments. To meet the increasing heat dissipation needs of modern CPUs, the water block features a nickel-plated pure copper cold plate, CNC-machined for maximum contact and efficiency. The top is crafted from durable black POM Acetal, while the hold-down bracket is made from laser-cut stainless steel, ensuring long-term mechanical integrity in continuous operation. The block includes four G1/8” side ports, allowing flexible and low-profile tubing arrangements — ideal for use in compact 1U server environments. Its refined internal design is engineered for high flow efficiency and stability, even in demanding rack-mounted systems. With no compromises on performance or build quality, the EK-Pro CPU WB 4189 Rack offers exceptional cooling, robust mounting, and enterprise-ready design. Technical Specifications: Dimensions (L × H × W): 113 × 78 × 22.2 mm Materials: Nickel-plated copper, stainless steel, POM Weight: 0.481 kg Ports: 4 × G1/8” Mounting method: T30 Torx Working pressure: 2,500 Pa Maximum working pressure: 30,000 Pa (with EK-Pro Pump Reservoir Manifold), otherwise 75,000 Pa Operating temperature range: 5 – 60 °C Compatibility: Intel® Xeon LGA 4189 Origin: Made in Slovenia – EU Enclosed: EK-Pro CPU WB 4189 Rack – Nickel + Acetal 2 × EK G1/8” plugs EK-Loop Multi Allen Key (6 mm, 8 mm, 9 mm) 1 × Torx T30 Key 1 × 5 mm Allen Key Thermal grease (1 g)

All new: Phobya's improved thermal pads with 7W/mK are able to match even high-end thermal compounds! These "XT" thermal pads are perfectly suited to equalize height differences and uneven spots on coolers and cooled elements. The very flexible structure and low hardness allow great adaptivity to the cooling surface even at low contact pressures. The thermal pad equalizes the effect of irregularities from microscopic scale to visible scratches etc. The surface of the pad is equipped with a protective foil which needs to be removed before use. The pads can be used on VRAM modules on graphics cards as well as on the VRM modules on a Mainboard or almost any other application where a high-performance thermal interface is desired. Even elements with large surfaces such as North- or Southbridge on a Mainboard are no problem for this thermal pad as it has great thermal conductivity. As basic equipment and spare parts these thermal pads should be a part of any cooling enthusiast's equipment! Technical specifications: Colour: White Dimensions: 120x20x0,5mm Thermal conductivity: 7 W/mk maximum bridgeable gap: 0,5 mm electrically non-conductive Extent of delivery: 1x Phobya thermal pad XT 7W/mK 0.5mm (120x20mm) for ramplex, innovatek, Mips, Koolance Data sheet to the thermal pads This product has been reviewed for you (by):Script-BaseFreeocen

All new: Phobya's improved thermal pads with 7W/mK are able to match even high-end thermal compounds! These "XT" thermal pads are perfectly suited to equalize height differences and uneven spots on coolers and cooled elements. The very flexible structure and low hardness allow great adaptivity to the cooling surface even at low contact pressures. The thermal pad equalizes the effect of irregularities from microscopic scale to visible scratches etc. The surface of the pad is equipped with a protective foil which needs to be removed before use. The pads can be used on VRAM modules on graphics cards as well as on the VRM modules on a Mainboard or almost any other application where a high-performance thermal interface is desired. Even elements with large surfaces such as North- or Southbridge on a Mainboard are no problem for this thermal pad as it has great thermal conductivity. As basic equipment and spare parts these thermal pads should be a part of any cooling enthusiast's equipment! Technical specifications: Colour: White Dimensions: 120x20x0,5mm Thermal conductivity: 7 W/mk maximum bridgeable gap: 1 mm electrically non-conductive Extent of delivery: 1x Phobya thermal pad XT 7W/mK 1mm (120x20mm) for ramplex, innovatek, Mips, Koolance Data sheet to the thermal pads This product has been reviewed for you (by): Script-Base Freeocen

All new: Phobya's improved thermal pads with 7W/mK are able to match even high-end thermal compounds! These "XT" thermal pads are perfectly suited to equalize height differences and uneven spots on coolers and cooled elements. The very flexible structure and low hardness allow great adaptivity to the cooling surface even at low contact pressures. The thermal pad equalizes the effect of irregularities from microscopic scale to visible scratches etc. The surface of the pad is equipped with a protective foil which needs to be removed before use. The pads can be used on VRAM modules on graphics cards as well as on the VRM modules on a Mainboard or almost any other application where a high-performance thermal interface is desired. Even elements with large surfaces such as North- or Southbridge on a Mainboard are no problem for this thermal pad as it has great thermal conductivity. As basic equipment and spare parts these thermal pads should be a part of any cooling enthusiast's equipment! Technical specifications: Colour: White Dimensions: 120x20x0,5mm Thermal conductivity: 7 W/mk maximum bridgeable gap: 1,5 mm electrically non-conductive Extent of delivery: 1x Phobya thermal pad XT 7W/mK 1.5mm (120x20mm) for ramplex, innovatek, Mips, Koolance Data sheet to the thermal pads This product has been reviewed for you (by): Script-Base Freeocen

The Alphacool ES RTX 4000 Ada Ge. GPU cooler was developed for the Enterprise Series, but not only impresses with its improved cooling performance and compact design, but also with its matt carbon look.Connections at the rear?By using a thin and extremely stable carbon plate, it was possible to design this as a single-slot cooler without having to compromise on the copper base. In combination with the connections positioned at the rear, several coolers can be stacked on top of each other with ease. This well thought-out design saves space, simplifies tubing and enables seamless integration into the water loop.More performance!Alphacool has given special attention to increasing cooling performance. In addition to optimising the water flow within the cooler and the thickness of the copper block, 1mm high-performance heat conducting pads are used. These measures ensure that the components to be cooled are closer to the cooler, which leads to significantly more effective cooling of all important components.Copper or aluminium?High-quality copper is used for all water-bearing parts, which offers almost twice the thermal conductivity of aluminium. The copper is also chrome-plated instead of nickel-plated, which provides additional protection for the cooler. The chrome plating is more resistant to acids, scratches and other damages, which effectively prevents coatings from flaking off.Thermal paste & thermal padsThe scope of delivery includes Apex thermal compound, which is the most durable thermal compound Alphacool offers with its low silicone content. This electrically non-conductive paste is ideal for high contact pressures and is easy to work with thanks to its viscosity. Soft, high-performance thermal pads are also supplied, which adapt perfectly to the components to be cooled. Compatibility:- Nvidia RTX 4000 Ada Generation, 20GB GDDR6, 4x DP, bulk (900-5G190-2270-000) Technical dataDimensions (L x W x H)241,25 x 96,70 x 17,50mmHeight of the backplate1mmWeight (total)1100gCooler base materialChome-plated copperCooler top materialCarbonThreads2 x G1/4"Maximum working temperature60 °CPressure tested8 BarColorBlackWarranty: 3 years???? Warranty Terms

The Eisschicht from Alphacool can, like other thermal pads, compensate for the irregularities of heat sinks and the elements to be cooled. But it has a great feature: The Eisschicht consists of thermal paste with an embedded mesh! This ensures that the performance of these pads is much more efficient than normal thermal pads, regardless of the low W/mK value. In addition, a better distribution and filling between the surfaces is achieved. This also results in better air displacement. Due to their soft consistency, there is also no pressure on components or solder joints. Nvidia also uses this kind of pads for the Founders Edition. The Eisschicht can be easily cut to the desired size and attached to heat sinks without slipping.As a basic component or spare part, thermal pads belong in every well-organized computer tinkering corner! Technical dataDimensions (L x W x H)100 x 100 x 0,5mmThermal conductivity3 W/mKElectrical ConductiveNoColorwhite

The Rise Ultra Soft are Alphacool's performance oriented solution in the range of thermal pads. Due to their outstanding properties, they can almost be compared to a thermal paste. The Rise Ultra Soft thermal pads nestle much better to components, which contributes to a significant improvement in cooling performance.Better than standard thermal pads?The material of the Rise Ultra Soft heat thermal pads acts similar to thermal paste. The consistency of the pads prevents the highest components, such as voltage converters or VRMs, from being subjected to increased contact pressure from the cooler. In extreme cases, this pressure can cause PCBs to bend. The Rise Ultra Soft Pads fill unevenness much better, nestle better against the components and thus significantly increase the heat transfer between the cooler and the component.But that is not the only advantage!The special material also cannot dry out. Usually, the silicone of heat-conducting pads bleeds out over time. This makes them go hard and the performance of the pads drops rapidly after a certain point. This is not the case with the Rise Ultra Soft thermal pads. They can be used for a much longer period of time without significantly losing performance.Cutting to size? No problem!When cutting the heat-conducting pads to size, it is essential to leave the foil on the pads. This makes it easy to cut the pads to size with scissors. This is just as easy as cutting paper. The cut edges remain perfectly clean and do not fray.The Alphacool Rise Ultra Soft thermal pads offer better performance than standard thermal pads in many respects and are a perfect replacement for old or underperforming pads. Technical dataDimensions (L x W x H)100 x 100 x 1mmSpecific Gravitiy ASTM D7923,3 g/ccThermal Conductivity ASTM D54707.0 W/mKHardness ASTM 224025 Shore OOUseful Temperature-40 to +160 °CVolume Resistivity ASTM D2575,2x1013 Ohm-mDielectric Constant ASTM D1504,5 MHzDielectric Breakdown Voltage ASTM D1495,5 kV/mmFlame Rating UL E331100UL94 V0Weight40 gColorGrey

The Rise Ultra Soft are Alphacool's performance oriented solution in the range of thermal pads. Due to their outstanding properties, they can almost be compared to a thermal paste. The Rise Ultra Soft thermal pads nestle much better to components, which contributes to a significant improvement in cooling performance.Better than standard thermal pads?The material of the Rise Ultra Soft heat thermal pads acts similar to thermal paste. The consistency of the pads prevents the highest components, such as voltage converters or VRMs, from being subjected to increased contact pressure from the cooler. In extreme cases, this pressure can cause PCBs to bend. The Rise Ultra Soft Pads fill unevenness much better, nestle better against the components and thus significantly increase the heat transfer between the cooler and the component.But that is not the only advantage!The special material also cannot dry out. Usually, the silicone of heat-conducting pads bleeds out over time. This makes them go hard and the performance of the pads drops rapidly after a certain point. This is not the case with the Rise Ultra Soft thermal pads. They can be used for a much longer period of time without significantly losing performance.Cutting to size? No problem!When cutting the heat-conducting pads to size, it is essential to leave the foil on the pads. This makes it easy to cut the pads to size with scissors. This is just as easy as cutting paper. The cut edges remain perfectly clean and do not fray.The Alphacool Rise Ultra Soft thermal pads offer better performance than standard thermal pads in many respects and are a perfect replacement for old or underperforming pads. Technical dataDimensions (L x W x H)50 x 50 x 3mmSpecific Gravitiy ASTM D7923,3 g/ccThermal Conductivity ASTM D54707.0 W/mKHardness ASTM 224025 Shore OOUseful Temperature-40 to +160 °CVolume Resistivity ASTM D2575,2x1013 Ohm-mDielectric Constant ASTM D1504,5 MHzDielectric Breakdown Voltage ASTM D1495,5 kV/mmFlame Rating UL E331100UL94 V0Weight28 gColorGrey

The Rise Ultra Soft are Alphacool's performance oriented solution in the range of thermal pads. Due to their outstanding properties, they can almost be compared to a thermal paste. The Rise Ultra Soft thermal pads nestle much better to components, which contributes to a significant improvement in cooling performance.Better than standard thermal pads?The material of the Rise Ultra Soft heat thermal pads acts similar to thermal paste. The consistency of the pads prevents the highest components, such as voltage converters or VRMs, from being subjected to increased contact pressure from the cooler. In extreme cases, this pressure can cause PCBs to bend. The Rise Ultra Soft Pads fill unevenness much better, nestle better against the components and thus significantly increase the heat transfer between the cooler and the component.But that is not the only advantage!The special material also cannot dry out. Usually, the silicone of heat-conducting pads bleeds out over time. This makes them go hard and the performance of the pads drops rapidly after a certain point. This is not the case with the Rise Ultra Soft thermal pads. They can be used for a much longer period of time without significantly losing performance.Cutting to size? No problem!When cutting the heat-conducting pads to size, it is essential to leave the foil on the pads. This makes it easy to cut the pads to size with scissors. This is just as easy as cutting paper. The cut edges remain perfectly clean and do not fray.The Alphacool Rise Ultra Soft thermal pads offer better performance than standard thermal pads in many respects and are a perfect replacement for old or underperforming pads. Technical dataDimensions (L x W x H)50 x 50 x 2mmSpecific Gravitiy ASTM D7923,3 g/ccThermal Conductivity ASTM D54707.0 W/mKHardness ASTM 224025 Shore OOUseful Temperature-40 to +160 °CVolume Resistivity ASTM D2575,2x1013 Ohm-mDielectric Constant ASTM D1504,5 MHzDielectric Breakdown Voltage ASTM D1495,5 kV/mmFlame Rating UL E331100UL94 V0Weight19 gColorGrey

The Apex Soft are Alphacool's high-end solution in the range of thermal pads. Due to their outstanding properties, they can almost be compared to a thermal paste. The Apex Soft thermal pads nestle much better to components, which contributes to a significant improvement in cooling performance. Better than standard thermal pads? The material of the Apex Soft heat thermal pads acts similar to thermal paste. The consistency of the pads prevents the highest components, such as voltage converters or VRMs, from being subjected to increased contact pressure from the cooler. In extreme cases, this pressure can cause PCBs to bend. The Apex Soft Pads fill unevenness much better, nestle better against the components and thus significantly increase the heat transfer between the cooler and the component. But that is not the only advantage! The special material also cannot dry out. Usually, the silicone of heat-conducting pads bleeds out over time. This makes them go hard and the performance of the pads drops rapidly after a certain point. This is not the case with the Apex Soft thermal pads. They can be used for a much longer period of time without significantly losing performance. Cutting to size? No problem! When cutting the heat-conducting pads to size, it is essential to leave the foil on the pads. This makes it easy to cut the pads to size with scissors. This is just as easy as cutting paper. The cut edges remain perfectly clean and do not fray. The Alphacool Apex Soft thermal pads offer better performance than standard thermal pads in many respects and are a perfect replacement for old or underperforming pads. Technical data L x W x H 120 x 20 x 1 mm Colour Grey Specific Gravitiy ASTM D792 3,4 g/cc Thermal Conductivity ASTM D5470 11.0 W/mK Hardness ASTM 2240 72 Shore OO Useful Temperature -40 to +150 °C Volume Resistivity ASTM D257 1.0x1011 Ohm-m Dielectric Constant ASTM D150 7,2 MHz Dielectric Breakdown Voltage ASTM D149 14 kV/mm Flame Rating UL 94 V-0 Weight 20 g Download Datasheet PDF: Alphacool Apex Soft Thermal Pad 11W/mk 2x 120x20x1mm

The Eisschicht Ultra Soft are Alphacool's performance oriented solution in the range of thermal pads. Due to their outstanding properties, they can almost be compared to a thermal paste. These Ultra Soft thermal pads nestle much better to components, which contributes to a significant improvement in cooling performance.Better than standard thermal pads?The material of the Ultra Soft thermal pads acts similar to a thermal paste. While normal thermal pads are only pressed together by the contact pressure there can be areas that are uneven due to different high components, making them less effective. With the ultra soft Eisschicht this problem doesn’t exist because the material distributes itself similar to thermal paste and thus prevents the highest components from being subjected to increased contact pressure by the cooler. As standard thermal pads are quite stiff they can also cause too much pressure on components. In the worst cases, this can cause the PCB to bend and even break. Due to the soft consistency of the Ultra Soft Eisschicht any excess material can spread out rather than cause problems. The Ultra Soft Eisschicht is not only performance orientated, but also safer!But this is not the only advantage!Moreover, the special material cannot dry out. Usually the silicone in thermal pads bleeds out over time. This makes them hard and the performance of the pads drops rapidly from a certain point. This is not the case with the Ultra Soft Eisschicht. They can be used over a much longer period of time without significantly losing performance.A thermal pad with fabric?The consistency of the heat conducting material is similar to a viscous heat conducting paste. A special fabric is embedded so that the material remains stable and can be used as a thermal pad. This ensures a perfect distribution of the material if the element to be cooled has an uneven shape. Examples include voltage transformers, VRam and similar electronic components of all kinds that require cooling.Cutting? No problem!To cut the thermal pads to size, you should definitely leave the foil on the pads. So the pads can easily be cut to size with a pair of scissors. This is just as easy as cutting paper. The cut edges remain perfectly clean and do not fray. Technical dataL x W x H100 x 100 x 1,5mmSpecific Gravitiy ASTM D2972,65 g/ccThermal Conductivity ASTM D54703.0 W/mKHardness ASTM 224020 Shore 00Working temperature40 to 200°COutgassing ASTM E5950,40% TMLVolume Resistivity ASTM D2576.2X10 high 13 Ohm-meterDielectric Constant ASTM D1505,5 MHzDielectric Breakdown Voltage ASTM D149>5000 VACFlame Rating UL E33110094 V0Colorwhite

With the HEATKILLER® V, Watercool is starting a new generation of coolers for the current Nvidia RTX 30 graphics cards. Equipped with unique highlights, the current version of the HEATKILLER® V presents what is technically feasible. With an increased number of cooling fins, the cooling performance is increased directly above the graphics processor and thus the most important area is improved. The radiator base, milled from a solid block, establishes contact with all relevant components. The trend-setting dual-layer inflow distributes the water simultaneously on two levels. This ensures an air flow that is at least 30 percent higher than that of our previous generation. The broad and symmetrical flow paths reduce dead spots (standing water) to a minimum and accelerate the flow. The overall result increases not only the maximum cooling capacity but also the flow rate of the HEATKILLER® V. Thanks to the newly designed spacers made of high-performance plastic (PEEK), the 10mm solid copper block is ideally isolated from the circuit board. In addition to the technical innovations, the design of the cooler is also impressive. The screwless cover makes the entire block look like it was cast from a single source. The symmetrically designed channels underline the look of the cooler and make it a unique eye-catcher. The integrated aRGB strips are now standard in combination with the nickel-acrylic variants. This means that the HEATKILLER® V can be perfectly integrated into the lighting concept of the computer. Technical specifications: Base plate material: nickel-plated electrolyte copper Material cover: acrylic glass Cover material: black anodized aluminum Connection terminal material: Acetal Dimensions: (LxWxH): 230 x 119 x 21 mm Connection: 4x G ¼ inch (DIN ISO 228-1) Weight: Pressure tested: 2 bar Compatibility: Nvidia Geforce RTX 3080/3090 Scope of delivery: 1x HEATKILLER® V 1x HEATKILLER® LED Strip aRGB 1x mounting material Thermal Grizzly Kryonaut thermal paste

With the HEATKILLER® V, Watercool is starting a new generation of coolers for the current Nvidia RTX 30 graphics cards. Equipped with unique highlights, the current version of the HEATKILLER® V presents what is technically feasible. With an increased number of cooling fins, the cooling performance is increased directly above the graphics processor and thus the most important area is improved. The radiator base, milled from a solid block, establishes contact with all relevant components. The trend-setting dual-layer inflow distributes the water simultaneously on two levels. This ensures an air flow that is at least 30 percent higher than that of our previous generation. The broad and symmetrical flow paths reduce dead spots (standing water) to a minimum and accelerate the flow. The overall result increases not only the maximum cooling capacity but also the flow rate of the HEATKILLER® V. Thanks to the newly designed spacers made of high-performance plastic (PEEK), the 10mm solid copper block is ideally isolated from the circuit board. In addition to the technical innovations, the design of the cooler is also impressive. The screwless cover makes the entire block look like it was cast from a single source. The symmetrically designed channels underline the look of the cooler and make it a unique eye-catcher. The integrated aRGB strips are now standard in combination with the nickel-acrylic variants. This means that the HEATKILLER® V can be perfectly integrated into the lighting concept of the computer. Technical specifications: Base plate material: nickel-plated electrolyte copper Material cover: acrylic glass Cover material: annealed stainless steel Connection terminal material: Acetal Dimensions: (LxWxH): Connection: 4x G ¼ inch (DIN ISO 228-1) Weight: Pressure tested: 2 bar Compatibility: EVGA Geforce RTX 3080 XC3 EVGA Geforce RTX 3090 XC3 Scope of delivery: 1x HEATKILLER® V 1x HEATKILLER® LED Strip aRGB 1x mounting material Thermal Grizzly Kryonaut thermal paste

HEATKILLER V PRO graphics card coolers for Nvidia's RTX 4090 Founders Edition were specially developed to cope with the high power dissipation of 450 watts and more. In order to ensure a correspondingly high increase in performance, we opted for a modular high-performance base plate. Proven technologies such as the dual-layer airflow and the symmetrical cooling design have also been incorporated. The result in the form of the HEATKILLER V PRO series is impressive both visually and in terms of performance. Key points of the HK V PRO series: High performance base plate Selected high-performance thermal pads on GDDR6X RAM Dual layer inflow Symmetrical cooling design Design-integrated connection threads in the terminal Screwless design Insulating spacers made of high-performance plastic (Peek) CNC cut thermal pads Modular high-performance base plate In order to increase the cooling performance in the area of the GPU core, we have integrated a modular high-performance base plate into the heat sink. This ensures significantly higher cooling performance than a monolithic design thanks to finely slotted fins and the resulting increase in the cooling surface. We have chosen the fin structure in such a way that, in addition to increasing the performance of the GPU core, the flow is also kept high. All distances to heat-relevant components have been kept small, which means that the heat from thermal problem areas such as GDDR6X RAM and voltage converters is ideally dissipated. The PEEK spacers made from high-performance plastic ideally insulate the cooler from the circuit board and make installation easier. The legendary Kryonaut thermal paste from Thermal Grizzly ensures the best possible heat transfer. Dual layer inflow and symmetrical cooling design The dual-layer inflow, like the symmetrical cooling design, can also be found in the PRO version of our HEATKILLER V GPU cooler. The increased inflow is particularly important for the high-performance base plate. The splitting of the water into two levels ensures better flow through the cooler. The wide and symmetrical flow paths optimize the flow and thus the general performance of the HEATKILLER V Pro cooler. Selected high-performance thermal pads for GDDR6X Our development department has invested a lot of time in finding the ideal thermal pads for the hot GDDR6X RAMs. We have found a thermal pad that significantly reduces the temperatures around the GDDR6X RAM compared to the very good standard pads. Design-integrated side connection threads Another innovation is the connection threads integrated into the side of the terminal. Together with the screwless cover and the backplate included in the package, the result is a cooler that looks like a single unit. In order to achieve the best possible appearance, the HK V PRO was designed so that no electronic components of the circuit board are visible. Backplate in package The new cooler design relies on assembly including a backplate. In our case, the black backplate ensures improved distribution of forces around the cooling block. In addition to an impressive look, this also results in better temperatures. Made in Germany Production is carried out with the greatest care on our state-of-the-art CNC machinery in Waren an der Müritz. Many work steps are carried out by hand and each product is completed according to the four-eyes principle. Made in Germany, as you would imagine. Technical data: Base plate material: electrolytic copper nickel-plated Lid material: ACETAL Material connection terminal: Acetal Dimensions: (LxWxH): 220 x 124 (incl. terminal) x 32.8mm (incl. backplate) Connection: 4x G ¼ inch (DIN ISO 228-1) Approved up to 1 bar Compatibility: NVIDIA GeForce RTX 4090 Founders Edition Scope of delivery: 1 x HEATKILLER® V PRO ACETAL 1 x HEATKILLER® V PRO backplate black 1 x Dual Slot Bracket 1 x mounting material 1 x Thermal Grizzly Kryonaut thermal paste Chip manufacturer: NVIDIA for GPU chip series:GeForce® RTX 4090 Base material: nickel-plated copper Upper material:ACETAL

The small heat sinks are the perfect addition for cooling various electronic components such as the graphics card VRam, the voltage transformer on a motherboard, or even in a power amplifier or in RC vehicles. To ensure maximum heat capacity and cooling performance, the coolers are made of copper. Alphacool uses a special coating to prevent the infamous greenish discolouration on copper as much as possible. This increases the lifespan of the cooler and ensures steady cooling performance. The coolers can be installed onto the desired components with optional thermal paste or self-adhesive thermal pads. Technical Data Dimensions: 10 x 10mm Material: Fullcopper Scope of Delivery Alphacool GPU RAM Copper Heatsinks 10x10mm - 10pcs

Wärmeleitpaste auf Aluminiumoxid-Basis, Anwendungsbereich zwischen -150 °C und 350 °C, 1,5 g Füllmenge, elektrisch nichtleitend