DEMCiflex Dust Filter 120mm Round Black/White DF0525Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 120 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Firstly, it is easy to see if cleaning is necessary again - as soon as the white filter fabric has a gray haze, you should do this task. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside of the fan frame. If one of the two arrows points towards the interior, it is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Figure 4 shows an example configuration on a housing (not included). As can be seen, the use of LED fans is possible because the transparent material hardly hampers the lighting. Technical details:Size (frame): Ø approx. 138 mmSize (filter): Ø approx. 113 mmCompatibility: 120 mm fan slotMaterial (filter): polyester meshColor: black (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
Funktionaler Fan-, Pumpen- und RGB-LED-Controller, mit separatem LC-Display, bis zu 4 Lüfter mit oder ohne PWM, 4x RGB (12VGRB) & 4x adressierbares RGB (5VDG), inklusive Fernbedienung
This bracket from BarrowCH, made of aluminium, allows 360 radiators to be mounted at an angle other than that specified by the enclosure and sometimes even in rather unusual places, such as externally. Technical Data Material: Aluminium Color: Black Radiator compatibility: 360
The retention rings attach the tops to both ends of the acrylic tubes. As they are included as standard with the Protium reservoirs, this item serves as a replacement or to exchange rings of a different colour. Technische Details Material: Aluminium Colour: Silver Compatibility: Protium series Scope of delivery 2x retention ring
This CPU cooler is especially well-suited for budget and midrange gaming PCs. Whether with ARGB lighting or without, the cooler delivers optimal cooling for the heart of your build thanks to its powerful, efficient, and durable fan.Long-lasting and low-vibration operation thanks to fluid dynamic bearingFour heatpipes ensure efficient heat transferCompatible with popular and older Intel and AMD socketsHigh airflow and static pressure efficiently cool the heatsinkMontech NX400: CPU cooler for budget and midrange buildsA fan with fluid dynamic bearing and a large aluminum heatsink with four heatpipes—these two features define the Montech NX400 CPU cooler. Although designed for budget and midrange gaming PCs, it can efficiently handle CPUs up to the Intel Core i9.Powerful fan with long lifespanIn addition to a high speed of 2,000 RPM, high airflow, and high static pressure, the fan also boasts an especially long lifespan. This is thanks to the fluid dynamic bearing in the fan, which enables both low-vibration and long-lasting rotor operation.Vibration-dampening pads also help reduce vibrations from the fan and fully eliminate any resonant oscillations that can cause unwanted noise.
This CPU cooler is especially well-suited for budget and mid-range gaming PCs. Whether with ARGB lighting or without, the cooler offers optimal cooling for the heart of your build, thanks to its powerful, efficient, and durable fan. Durable and low-vibration operation thanks to fluid dynamic bearing Four heatpipes ensure efficient heat transfer Supports both current and older Intel and AMD sockets High airflow and static pressure efficiently cool the heatsink Montech NX400: CPU cooler for the budget and mid-range segment A fan with a fluid dynamic bearing and a large aluminum heatsink with four heatpipes: these two features define the Montech NX400 CPU cooler. Although the cooler is designed for budget and mid-range gaming PCs, it can even efficiently handle CPUs like the Intel Core i9. Powerful fan with long lifespan In addition to a high speed of 2,000 revolutions per minute, as well as high airflow and static pressure, the fan also boasts a particularly long lifespan. This is due to the bearing in the fan, which enables vibration-dampened and long-lasting rotor operation. Vibration-dampening pads also help to reduce fan vibrations and completely eliminate any resonance that could cause unwanted noise.
The nickel-plated temperature sensor in the colour shiny silver from Bitspower is an easy way to keep an eye on the water temperature of a water cooling system. To do this, the sensor, which has a sealing ring, is screwed into a G1/4" thread, whereby an internal extension then measures the temperature of the surrounding water. With a 90cm long 2-pin cable, the sensor can be connected to a display or control unit or to a compatible motherboard. This allows, for example, the rotation speed of radiator fans to be automatically controlled depending on the water temperature. Technical Data: Material: Nickel-Plated Brass Colour: Shiny Silver Thread: G1/4" Thread Length: 4 mm Sensor Length: 8 mm 2-Pin Cable: 90 cm
To connect the individual components of the water cooling, the choice of the correct connections and their sufficient number is essential. Otherwise, installation will quickly become a frustrating experience if assembly fails on the wrong or too few connectors and is delayed due to this. Bitspower offers a comprehensive product range that offers the right solution for every requirement - whether adapters, direct hose connections, brackets or distributors. The design is solid and has a sealing ring. Thus, the connections remain tight and ensure high long-term durability. This is a shiny silver, nickel plated, straight adapter with two G1 / 4-inch external threads. The special feature: The length of the adapter can be flexibly adjusted between 22 and 31 mm (measured without thread). For this purpose, only one nut is loosened, one side pulled out as desired and then fixed again with the union nut. Technical details:Material: brass, nickel platedConnections: male thread: 2x G1 / 4 inchLength: 22 - 31 mm (variable)
Tootekood: FD-FAN-PRI-AL12-3PGTIN: 7340172701606Jahutid ja lisad
Dimensions 120x120x25mm, Turns 1200rpm, Air flow rate 86.02m³ / h, Air pressure 1.27mmH₂O, Volume 19.5dB (A), Fan bearing LLS, Connection 3-pin, Voltage range 7-12V, Power consumption 1.2W, Special features RGB illuminated, RGB header (3-pin + 5V / DATA / GND), FD-FAN-PRI-AL12-3P
The HardTube project becomes a reality. Alphacool takes a completely new way and clearly sets!The method most commonly used previously for water cooling systems is normal PVC hoses - now Alphacool offers another approach to water cooling. The Alphacool HardTube again brings more tidiness into the system which makes a much more structured impression.Brand new plexi tubes with the Alphacool HT connectors make installation very simple, they connect completely sealed together. The plexi tube can be adapt to the system with the appropriate bending tool without needing to use additional angles.The following options are available:HardTube 13/10mm plexi Clear 20cm, 40cm, 60cm and 80cmHardTube 16/12mm plexi Clear 20cm, 40cm, 60cm and 80cm(also available in a pack of 4)Note: Due to the made-to-fit pipes, the connections must be plugged straight with a little effort.Scope of delivery:Alphacool HardTube 13/10mm plexi clear 80cm - 4pcsAttention: Not compatible with Monsoon fittings.
Technical Data: Material: Nickel-Plated Brass Colour: Black Supported Tube: 13/10 mm Thread: G1/4", male Thread Length: 4,5 mm Outer Diameter (Fitting): 20 mm Installed Height: 19 mm Compatible Soft Tubing: PVC, EPDM, Norprene, Silicone and most other flexible tubes
During the development of the new P14 PWM PST special emphasis was placed on a focused air flow and a high static pressure. The fan guarantees extremely efficient cooling, even with increased air resistance. Therefore, the P14 PWM PST is particularly suitable for use on heat sinks, radiators as well as pinhole and filters. Technical Details Fan: 140 mm, 200 - 1700 rpm (PWM controlled) Air flow: 72.8 CFM / 123.76 m³ / h (@ 1,700 rpm) Noise level: 0.3 sone (@ 1,700 rpm) Static pressure: 2.4 mm H2O (@ 1,700 rpm) Typical voltage: + 12 V DC Starting voltage: 3.9 V DC Cable length: 400 mm Sub PST Cable Length: 50 mm
DEMCiflex Dust Filter 140mm Black/White DF0382Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 140 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Firstly, it is easy to see if cleaning is necessary again - as soon as the white filter fabric has a gray haze, you should do this task. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside of the fan frame. If one of the two arrows points towards the interior, it is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Figure 4 shows an example configuration on a housing (not included). As can be seen, the use of LED fans is possible because the transparent material hardly hampers the lighting. Technical details:Size (frame): 153 x 153 mmSize (filter): 129 x 129 mmCompatibility: 140 mm fan slotMaterial (filter): polyester meshColor: black (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
Alphacool's Eiszapfen series is future-oriented and characterized by excellent workmanship and high flow. Ball valves have always been a flow brake, making life difficult for each pump. Then, Alphacool has developed a ball valve represents no obstacle to a diameter of 10mm. The inside scoop closes absolutely tight, thus preventing further escape of liquid. On both sides all 1/4“ connections with a maximum thread length of 6mm can be screwed. This ball valve is available in two different color versions: Chrome and Deep Black. Technical Details: Dimensions (LxBxW): 35,4 x 36 x 22,7mm Color: Deep Black Scope of delivery: Alphacool Eiszapfen 2-way ball valve G1 / 4 - Deep Black
Alphacool's Eiszapfen series is future-oriented and characterized by excellent workmanship and high flow. Ball valves have always been a flow brake, making life difficult for each pump. Then, Alphacool has developed a ball valve represents no obstacle to a diameter of 10mm. The inside scoop closes absolutely tight, thus preventing further escape of liquid. On both sides all 1/4“ connections with a maximum thread length of 6mm can be screwed. This ball valve is available in two different color versions: Chrome and Deep Black. Technical Details: Dimensions (LxBxW): 35,4 x 36 x 22,7mm Color: Chrome Scope of delivery: Alphacool Eiszapfen 2-way ball valve G1 / 4 - Chrome
The nickel-plated adapter in the color shiny silver couples two tubes, which do not run on a common straight line and provides at the adapter for a bend of 90 degrees. Two rubber rings seal both sides. The adapter is especially well compatible with the Crystal Link Tubes from Bitspower. Technical Data: Material: Nickel-Plated Brass Colour: Shiny Silver Angle: 90 ° Connections: 2x Ø 12 mm
The Black Ice® Nemesis® GTX radiators are the next generation of computer radiators from Hardware Labs. These radiators offer an improved cooling performance when using
The connection for 16mm (AD) Hard Tubes from EK Water Blocks, is a compression fitting made of nickel-plated brass. It is silver in colour and comes from the Torque series, which convinces with a simple and timeless design. Originally intended for the EKWB Quantum series, this fitting is also compatible with other EK products. In this fitting, the union nut serves as a compression ring, which presses the sealing ring onto the hard tube. It thus offers a higher level of safety and sealing than, for example, the fittings of the EK-HD series. As a small feature, the union nut has a recess under which coloured rings are placed, which provide a bit of individuality and are available separately. Technical Data: Material: Nickel-Plated Brass Colour: Silver Supported Tube: 16 mm OD Thread: G1/4", male Thread Length: 4,5 mm Outer Diameter (Fitting): 24 mm Installed Height: 15 mm Compatible Solid Tubing: Acrylic, PETG, Copper, Brass, Stainless Steel
