EK Water Blocks EK-Torque STC-13/10 color ring pack of 10, red. These exchangeable rings for the 13 / 10mm soft tube compression fittings from EKWB are made of aluminum, are available in different colors and give your system a unique look. Compatibility: EK-Quantum Torque STC-13/10 connections Technical specifications: Red color Material: aluminum Quantity: 10 pieces
The new generation of compact fan technology is on the market. Multiframe® fans have completely unique multi-piece chassis, which eliminates vibration already inside of the fan. Therefore resonance throughout the system is reduced. Additional measures for noise reduction such as the use of decoupling kits or insulation mats can be spared with these fans. Depending on the case used, Multiframe® fans are able to reduce the fan-induced noise below the noise from the airflow itself. Multiframe® fans are than "more silent than the air". The new Multiframe® technology has a array of new features: The integrated vibration absorbers are just one of the new features that all contribute to noise reduction. For example the vibration absorbers are wider than the chassis to avoid any contact between case and vibrating parts. The use of massive and heavy materials in the fan leads to a lowering of the noise's frequencies, therefore making it less audible and more comfortable to the human ear. Aerodynamic optimization of frame and strutting also reduce noise by air swirling. This reduces a majority of the noise through airflow and therefore a large part of the overall noise level of the fan. The other parts of the Multiframe® fan series are also on the highest technological level. The improved EKAplus motor is voltage-independent extremely quiet and has an especially low starting voltage. The bearing used is the new NB-NanoSLI® bearing, which is especially quiet and has a long lifespan thanks to a special lubrication system. The fan is also equipped with a reliable auto-restart mechanism and is protected against polarity reversal. Interesting is the fact that the noise level of the Multiframe® series is almost completely dependent from the case they are installed in, as noise produced directly by the is reduced to a minimum and usually below the noise level of the airflow. Thereby these fans are more quiet than their airflow. With this new generation and advance in noise reduction more and more responsibility for noise reduction is in the hands f the case manufacturers. If full advantage is to be taken of these fans an aerodynamically optimized case has to be used, which does not obstruct airflow with tight meshes or other obstructions. Technical details: Dimensions: 80x80x25mm Speed (+- 10%): 1700rpm Airflow: 47m³/h Noise level: 14 dB(A) Voltage range: 4,5-13,8V Starting voltage: 4,5V Power consumption: 1,2W Warranty: 6 years
Toote kirjeldus inglise keeles:To connect the individual components of the water cooling, the choice of the correct connections and their sufficient number is essential. Otherwise, installation will quickly become a frustrating experience if assembly fails on the wrong or too few connectors and is delayed due to this. Bitspower offers a comprehensive product range that offers the right solution for every requirement - whether adapters, direct hose connections, brackets or distributors. The design is solid and has a sealing ring. Thus, the connections remain tight and ensure high long-term durability. This is a straight G1 / 4 inch screw connection for 13 / 10mm hoses (1/2 inch outer diameter - 3/8 inch inner diameter) with union nut in matt black finish. Technical details:Material: brass, black nickel platedColor: matt blackConnections: Thread: G1 / 4 inch hose: 13/10 mm
The Bitspower fittings are the ideal complement for water cooling systems. The G1/4" screw connection with union nut in shiny black is suitable for 16/10mm Soft Tubes (as well as for 16/11mm). Technical Data: Material: Nickel-Plated Brass Color: Shiny Black Thread: G1/4 Zoll Thread Length: 5 mm Tubing Size: 16/10 mm (ID 3/8", OD 1/2")
DEMCiflex Dust Filter 140mm White DF0689Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 140 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Note:The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Technical details:Size (frame): 153 x 153 mmSize (filter): 129 x 129 mmCompatibility: 140 mm fan slotMaterial (filter): polyester meshColor: white (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
This bracket from BarrowCH, made of aluminium, allows 360 radiators to be mounted at an angle other than that specified by the enclosure and sometimes even in rather unusual places, such as externally. Technical Data Material: Aluminium Color: Black Radiator compatibility: 360
The Barrow mini Water Stop Valve is made of full metal. Its construction makes it extremely robust. The housing is made of copper and the handle is made of aluminum. The stopcock has a G1 / 4 “internal thread with a length of approx. 5mm on both sides. Technical specifications: Color: black housing / black handle Material: copper / aluminum handle Thread: 2x G1 / 4 " Thread length: 5mm Dimensions: 37.2 x 35.5 x 23mm Flow opening: 10mm Scope of delivery: Barrow mini water stop valve
With the Alphacool Core XP³ Acetal light you get a very compact CPU water block for all current mainstream sockets from AMD and Intel. It offers the typical high Alphacool quality paired with excellent performance at a fantastic price. High cooling capacity! The cooling plate has been optimised to give the best performance for the price point. The nickel-plated copper radiator bottom has a surface area of 56 x 56 mm with a cross-slot structure and only 0.4 x 1 mm thick pins through which the water can flow. Due to the extremely large cooling surface, the water can effectively absorb the heat from the radiator bottom and remove it from the CPU area. The pin area is about 27.6 x 37.6 mm ensuring that most mainstream CPUs are covered completely which guarantees high cooling performance. The new multiple slotted nozzle plate was developed especially for this cooler to achieve a perfect interplay of water flow and inflow of the base plate. Only the combination of all these little things ensures the high performance. Quick assembly! The mounting bracket is simply put over the CPU cooler. All mounting screws can be pre-assembled onto this Then you can simply screw it down. A well-illustrated manual with large render graphics is included so that the installation is easy to understand. Compatibility: Intel: 1056 / 1155 / 1150 / 1151 / 1200 / 1700 / 2011 / 2011-3 / 2066 AMD: AM5 / AM4 / AM3+ / AM3 / AM2 Technical data L x W x H 73 x 63 x 21mm Weigth 113g Max working temperature 60°C Material cooling plate nickel plated copper Material cooler top Acetal Connections 2 x G1/4"
Alphacool's Eiszapfen is the high-end version of the already proven connectors and meets all the requirements placed on a connector with its high-flow, shape, processing and colour. Compatibility This 90° angled adapter has a rotatable 1/4" external thread on one side and a 1/4" internal thread on the other. This 90° angled connection is mostly used where space is limited and a special solution is required. For maximum flexibility, the adapter can be rotated on the external thread. Design With brilliant chrome, deep matt black and decent matt white, three colour variants are available that fit perfectly into any system. Thanks to special processes, the coatings are firmly bonded to the substrate. This ensures a high longevity of the colours and prevents the coating from flaking off. The connector now also has the Alphacool logo, which makes it unique in addition to its special shape! Technical details Material Brass Colour White Length 34 mm Diameter 18 mm Thread G1/4“ Thread length 5 mm Weight 38 g Download Datasheet PDF: Alphacool Eiszapfen L-connector rotatable G1/4 outer thread to G1/4 inner thread - White Fitting Map: You can find an interactive map of all Alphacool fittings here.
The nickel-plated adapter in the color shiny black couples two tubes, which do not run on a common straight line and provides at the adapter for a bend of 60 degrees. Two rubber rings seal both sides. The adapter is especially well compatible with the Crystal Link Tubes from Bitspower. Technical Data: Material: Nickel-Plated Brass Colour: Shiny Black Angle: 60 ° Connections: 2x Ø 12 mm
The nickel-plated adapter in carbon black couples two tubes which do not run on a common straight line and provides a 90 degree bend at the adapter. Two rubber rings seal both sides. The adapter is especially well compatible with the Crystal Link Tubes from Bitspower. Technical Data: Material: Nickel-Plated Brass Colour: Carbon Black Angle: 90 ° Connections: 2x Ø 12 mm
The adapter in carbon black from Bitspower is especially designed for the connection of two graphics cards with SLI/ Crossfire to bridge the short distance. If two graphics cards are used, two of the adapters are also required. They are sealed with two rubber rings. The adapter is especially well compatible with Bitspower's Crystal Link Tube series. Technical Data: Material: Nickel-Plated Brass Colour: Carbon Black Connection: 12 mm (OD) Thread: G1/4" Thread Length: 5 mm
The adapter in carbon black from Bitspower has a G1/4" external thread and a G1/4" internal thread. It has an angle of 90 degrees. Technical Data: Material: Brass Colour: Carbon Black Angle: 90 ° Thread: G1/4" and inner G1/4" Thread : G1/4" Thread Length : 5 mm Thread : Inner G1/4" Thread Length : 6 mm
This filler neck in carbon black from Bitspower is used when coolant is filled into the cooling circuit from the top of the housing. To do this, cut a small opening in the housing, place the connection through the hole or on the edge of the hole and screw it on from the other side with the screw ring. The filler neck can be connected to the cooling circuit via a normal G1/4" female thread connection. After filling, the upper side should be sealed with a sealing plug. Technical Data: Material: Brass Colour: Carbon Black Thread: Inner G1/4" Thread Length: 15 mm
Fan speed (max): 1500 Fan speed (min): 600 Air flow rates: 70.32 Number of fans: 3 Noise: 30.4 Weight: 558 Other features: Patented TT RGB PLUS Software & App Hydraulic Bearing
Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside or inside of the fan frame. If one of the two arrows points towards the interior or if the rotor suspension is aligned with the interior, this is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate.
The nickel-plated adapter from Bitspower in the colour shiny silver, has an angle of 90 degrees and two G1/4 inch internal threads, with rubber seals on both sides. Technical Data: Material: Nickel-Plated Brass Main Color: Shiny Silver Angle: 90° Thread: Inner G1/4" Thread Length: 6 mm
Backplate mit aktiver Kühlung von EK Water Blocks, für EVGA XC3 RTX 3080 / 3080 Ti und 3090, vernickelter Kupferboden, Acryl-Deckel, adressierbare RGB-Beleuchtung
The new Eiszapfen PRO hard tube fittings from Alphacool are the next step in development for the familiar Eiszapfen fittings. In the development of the fittings Alphacool concentrated on a specific problem, deforming PETG hard tubes at high temperatures. PETG can start to deform at 60°C. Although such a temperature is usually rarely reached, it can still occur. The Eiszapfen PRO fittings prevent this problem from the outset and hold the tubes in position. The deformation is prevented by the new nylon inserts inside and stabilizes the hard tubes. Furthermore, the fitting still has an O-ring and a compression seal. However, the contact area is much larger than with normal O-rings, which provides a better grip. With the insert and the compression seal, the tube is strengthened from the inside and outside. Even under heavy loads the HardTube does not slip. Alphacool has tested the tensile strength of up to over 8kg, so there is no need to worry about loose tubing. Technical details: Material: brass Colour: chrome Diameter: 22 mm Height: 20 mm Thread: G1/4" Thread length: 5 mm HardTube size: 13 mm Compatibility: PETG, acrylic, brass and glass tubes Weight: 0,023 kg Scope of supply: 1x Alphacool Eiszapfen PRO 13mm HardTube Fitting G1/4 - Chrome Notice: Attention: The manufacturer Mayhems advises that Mayhems fluids, especially the Aurora line of products, have been manufactured and distributed solely for show and modding purposes. These should not be utilized in the system for more than 14 days. We would also like to advise that Mayhems fluids can damage water cooling products, and using Mayhems fluids can thereby void the warranties offered by the following manufacturers: Koolance, Phobya, Alphacool, Aqua Computer, Watercool. Damages such as: clogging, corrosion of aluminium radiators, deterioration of glued containers, etc., are a consequence of the use of Mayhems, but will not be reimbursed by Mayhems. Use is therefore at one’s own risk.
Alphacool's Eiszapfen connector series is the high-end execution of these tried-and-true fittings! Everything you want in a compression fitting is here: highflow, form, processing and colour. A refusal to compromise in development and production has made the Eiszapfen series into what it is. Fittings are available in brilliant chrome or a deep, matte black, which will fit excellently into any system. A special procedure binds the outer coating firmly to the surface, improving the longevity of the intense colour and preventing any chipping or peeling of the coating. Every connector now has the Alphacool logo, which along with their distinctive shape makes them unmistakable! Anyone looking for colourful options has them: the O-rings in the shipment come in three colours. With the available UV-light option, these will even light up in the corresponding colour. Model: Double nippleThis adaptor has a 1/4" outer thread on each side. It could be used to connect two sockets with 1/4" inner threads, for example. Technical Details Material: brass Colour: black Dimensions Length: ca. 15mm Diameter: 18mm Scope of Delivery 1x Alphacool Eiszapfen double nipple G1/4 outer thread to G1/4 outer thread - black Fitting MapYou can find an interactive map of all Alphacool fittings here.
