Low-Noise-Pumpe von Alphacool und Laing, Schwarzes Messing-Gehäuse (Black Nickel), möglich, 200 l/h und 2,44 m Förderhöhe bei 10 Watt Leistungsaufnahme, Single Edition ohne Aufsatz
The None Chamfer PETG Link Tube in transparent by Bitspower is made of polyethylene terephthalate, PETG for short. This material is a plastic and is used, for example, for PET bottles. Its strength lies in its high break resistance, easy heatability and high stability. In order to implement them in the system, it is necessary to bend them into shape with heat and cut them to size. As a rule, the None Chamfer does not need to be reworked when it is cut. The tube measures 50cm in length, 14mm in outer diameter and 11mm in inner diameter. Only the EML series from Bitspower is compatible as connections. Technical Data: Material: PETG Color: Transparent Outer Diameter: 14 mm Inner Diameter: 11 mm Length: 50 cm Compatibility: EML series Bitspower connectors only
The None Chamfer PETG Link Tube in transparent by Bitspower is made of polyethylene terephthalate, PETG for short. This material is a plastic and is used, for example, for PET bottles. Its strength lies in its high break resistance, easy heatability and high stability. In order to implement them in the system, it is necessary to bend them into shape with heat and cut them to size. As a rule, the None Chamfer does not need to be reworked when it is cut. The tube measures 50cm in length, 12mm in outer diameter and 10mm in inner diameter. Only the EML series from Bitspower is compatible as connections. Technical Data: Material: PETG Color: Transparent Outer Diameter: 12 mm Inner Diameter: 10 mm Length: 50 cm Compatibility: EML series Bitspower connectors only
1000ml blue pastel based non-transparent and high performance coolant for PC water-cooling, offering superb protection for copper, nickel, brass, and aluminum.
The CORSAIR Hydro X Series XR5 140 mm Water Cooling Radiator delivers extreme custom cooling performance, with an 30 mm radiator thickness and premium copper core.
Plug for connecting cables to the potential-free switching contact (relay) of the aquaero. The plug can be attached to a cable using screw terminals and is then plugged into the appropriate plug on the aquaero. Two-pole design. Please note the maximum load capacity of the relay output of the aquaero! Max. 1A, max 12V!
The nickel-plated plugs from Bitspower in the colour shiny black can be screwed into a G1/4" internal thread for a certain time or permanently, e.g. to close radiators or equalizing tanks. The grip of the sealing plug is particularly noble and practical. Technical Data: Material: Nickel-Plated Brass Colour: Shiny Black Thread: G1/4" Thread Length: 5 mm
The nickel-plated plugs from Bitspower in the colour shiny silver can be screwed into a G1/4" internal thread for a certain time or permanently, e.g. to close radiators or equalizing tanks. The grip of the sealing plug is particularly noble and practical. Technical Data: Material: Nickel-Plated Brass Colour: Shiny Silver Thread: G1/4" Thread Length: 5 mm
The cooling units from Hailea have been used in trusted waterchillers from other manufacturers for over 15 years. The new heat exchangers of the Ultra series are made from titanium. Therefore the chillers are perfect for watercooling systems. Another positive aspect about the Hailea units is the low noise emission. The pricing of the new series is also pleasantly affordable. New revision: New cool design More robust materials for even longer lifespan Lowered noise emissions Suitable for continuous operation Noise emissions: The small chillers (like HC150) have a noise emission of 20dB(A) only and can be used near the computer / aquarium without disturbing. Bigger models (like HC500) should be additionally decoupled to reduce the noise level if necessary The models HC1000 und HC 2000 should be extra decoupled or maintained in a seperate room. This waterchiller basically replaces the radiator as the coolant is chilled to the desired temperature by this unit. Temperatures down to 4°C are possible, please note that at low temperatures (high temperature difference) condensate may accumulate. Suitable insulation accessories are also available in our shop. Alternatively the coolant temperature can be set to just below room temperature to avoid this problem. Thanks to the low temperatures incredible overclocking potential is available! The lifespan of the components is extended by multiples. This system is also great for no-noise applications as the chiller can be located in another room. We recommend integration of the chiller into the cooling loop in combination with a radiator. This allows use of the chiller when required (overclocking, Benchmarks, summer etc..) and use of the radiator during normal operation. To estimate the required cooling performance here some non-binding estimates. The exact thermal emissions can be requested from the manufacturer of the hardware. CPU: 80W (standard) to 150W (overclocked) GPU: 50W (small cards) to 250W (GTX 980) MB: 20 to 40W per component The added values of your system must not exceed the given cooling capability of the chiller. What aquarium size can be cooled with my water chiller? The manufacturer provides the following data: Model / aquarium size in liters: HC-130 / 50-100L HC-150 / 50-200L HC-250 / 100-300L HC-300 / 100-400L HC-500 / 200-800L HC-1000 / 300-1000L HC-2000 / 400-1500L We at Aquatuning wish to advise you that the manufacturer’s data was obtained under optimal circumstances. The temperature response of the aquarium may greatly vary because of insulation, heat from lights respectively sunlight. Hence we recommend using the larger model when reaching the upper limit of the aquarium size values. Notes regarding shipment: For shipping via parcel delivery (GLS) we have manufactured a specially padded carton. For handling and packaging we must charge 15€ incl. VAT. This charge is not charged when the Chiller is picked up or with pallet shipment if the chiller is shipped without the special packaging. Note regarding shipping: This unit can only be shipped via a forwarding company. As the chipping charges differ by distance an online calculation is not possible. Please provide your full telephone number and E-Mail address when ordering, we will contact you after the order is complete. The shipping charge is approximately 50€ within Germany. Technical specifications: Power: 1/6 HP Power consumption: 150W Cooling capacity: 265W (suitable for extreme OC and cooling) Recommended coolant flow: 600-2200 l/h Weight: 18kg Cooling agent: R134A Dimensions: 448x330x440mm (LxWxH) Connector outside diameter: 18-20mm Heat exchanger material: Titanium max. compressive load: 0,8bar Temperature adjustments: Digital read-out (precision 0,1°C), temperature setting in 1°C steps current demand: 1.3 A (50 Hz) current drain: 299 W Scope of Delivery: 1x Waterchiller Hailea Ultra Titan 300 2x 45° angle with rubber seal 2x rubber seal with G1/4" internal thread 2x suitable hose clamps Note for first-time users: If you should have problems with your chiller please contact us before returning the chiller to us. In most cases there is no actual problem with the chiller, but the functionality of the unit is not fully understood by the user yet. Please note the following: The compressor unit automatically switches itself on and off, if the temperature sensor is manipulated your warranty is void, the noise level or an allegedly not sufficient cooling performance are no reason for a reclamation. The chiller can only function properly if the cooling loop is equipped with a sufficiently powerful pump. If these facts are considered most reclamations can be avoided and you will greatly enjoy this product! Note for aquarium-use: The cooling performance is affected by the aquarium-lamp the reduced pump power due to filters and the thermal waste of the pump. We therefore recommend to order the ciller at least on power-lever higher that theoretically calculated This product has been reviewed for you (by): Overclockingstation Zockon bit-tech (engl.)
The Kaze Flex RGB PWM series combines the award-winning technology of the Kaze Flex fans with an optical revision and RGB LEDs. The all-black frame and decouplers emphasize the translucent fan blades illuminated by eight LEDs. A 4-pin 12V RGB connector allows regulation by standard RGB controllers. Thanks to an additional pass-through plug, several fans can be chained together. The outstanding performance of the Kaze Flex range remains untouched. The Sealed Precision FDB bearing ensures a service life of more than 120 000 hours. Three performance levels offer an individual solution for every application. A regular RGB fan version is also available. Technical Details Dimensions: 120 x 120 x 27 mm Fan Speed: 300 - 1800 ± 10% rpm Noise Level: 4.0 - 35.8 dBA Airflow: 16.6 - 43.03 CFM = 28.2 - 73.1 m³/h Static Pressure: 0.0763 - 2.40 mmH²O | 0.75 - 25.3 Pa Voltage: 12 V Amperage: 0,09 A / 0,13 A / 0,40 A Amperage LED: 0,40 A / 0,40 A /
The construction of a quiet computer is always a challenge, especially if performance and proper cooling are also a factor. The SF01 consists of two foam plastic sheets which help with noise absorption with minimal pressure inside of the system. Each sheet has a large surface and is made from very dense foam plastic with a thickness of 4mm. This ensures good noise reduction and flexible integration. Special features: Special high-grade EPOM foam plastic material for noise absorption Excellent adhesive properties even at high temperatures Simply cut to size: Fits in any computer case Contains two foam sheets Technical specifications: Colour: Black Material: EPOM Dimensions (WxLxD): 530x380x4mm Extent of delivery: 1x Silverstone noise absorption sheet (SST-SF01)
EK-Quantum Vector Strix RX 5700 +XT Backplate is a CNC machined retention backplate made from black anodized aluminum for EK-Vector Radeon RX 5700 +XT series water blocks. Backplate covers the whole length of graphics cards PCB, serves as an aesthetic add-on and also provides passive cooling for the backside of the voltage regulation module (VRM). This backplate is guaranteed to be compatible with ROG Strix Radeon™ RX 5700 XT series graphics cards. Enclosed: - EK-Quantum Vector Strix RX 5700 +XT Backplate - Black - Mounting mechanism - Thermal pads Made in Slovenia - Europe!
Dimensions 140x140x25mm, Revolutions 550-1250rpm, Air throughput 85.29m³ / h, Air pressure 1.40mmH₂O, Volume 26dB (A), Fan bearing hydrodynamic plain bearing, Voltage range 6-13.2V, Power consumption 3.96W, Connection 4-pin PWM, 4-pin Corsair RGB, RGB lighting (34 LEDs), Special features LED control, CO-9050106-WW
DEMCiflex Dust Filter 80mm Black/White DF0430Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 80 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Firstly, it is easy to see if cleaning is necessary again - as soon as the white filter fabric has a gray haze, you should do this task. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside of the fan frame. If one of the two arrows points towards the interior, it is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Figure 4 shows an example configuration on a housing (not included). As can be seen, the use of LED fans is possible because the transparent material hardly hampers the lighting. Technical details:Size (frame): 105 x 105 mmSize (filter): 80 x 80 mmCompatibility: 80 mm fan slotMaterial (filter): polyester meshColor: black (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
DEMCiflex Dust Filter 92mm Round Black/White DF0489Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 92 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Firstly, it is easy to see if cleaning is necessary again - as soon as the white filter fabric has a gray haze, you should do this task. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside of the fan frame. If one of the two arrows points towards the interior, it is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Figure 4 shows an example configuration on a housing (not included). As can be seen, the use of LED fans is possible because the transparent material hardly hampers the lighting. Technical details:Size (frame): Ø approx. 110 mmSize (filter): Ø approx. 85 mmCompatibility: 92 mm fan slotMaterial (filter): polyester meshColor: black (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
Alphacool's Eiszapfen series is future-oriented and characterized by excellent workmanship and high flow. Ball valves have always been a flow brake, making life difficult for each pump. Then, Alphacool has developed a ball valve represents no obstacle to a diameter of 10mm. The inside scoop closes absolutely tight, thus preventing further escape of liquid. On both sides all 1/4“ connections with a maximum thread length of 6mm can be screwed. This ball valve is available in two different color versions: Chrome and Deep Black. Technical Details: Dimensions (LxBxW): 35,4 x 36 x 22,7mm Color: Chrome Scope of delivery: Alphacool Eiszapfen 2-way ball valve G1 / 4 - Chrome
This G1/4 Inch screw plug can be used for many applications. So you can use it for the radiator, reservoir and some other components. Alphacool have this plug screw in 2 different colors: Chrome and Deep Black. Thus you can now bring your modding project in a uniform color to shine . Technical specifications: Material: Brass Colour: Deep Black Thread size: G1/4 Inch Height without thread: 4,25mm Top diameter: 18mm Extent of delivery: 1x Alphacool Screw with O-Ring G1/4 Inch - Deep Black
Alphacool’s Eiszapfen Connector Series is the high-end execution of these tried-and-true connectors! Every requirement you could have of a connector is met with this series: highflow, form, processing and colour. A refusal to compromise in development and production has made the Eiszapfen series into what it is. Components are available in brilliant chrome or a deep, matte black, which will fit excellently into any system. A special procedure binds the outer coating firmly to the surface, improving the longevity of the intense colour and preventing any chipping or peeling of the coating. Every connector now has the Alphacool logo, which along with their distinctive shape makes them unmistakable! Anyone looking for colourful options has them: the O-rings in the shipment come in three colours. With the available UV-light option, these will even light up in the corresponding colour. Model: Extension 20mmThis slim adapter extends a ¼” thread by 20mm. This is mainly useful where a ¼” track is hard to reach or sits too far in. Technical Specifications: Material: Brass Colour: Deep Black Dimensions: Length: 20mm Diameter: 18mm Scope of Delivery: 1x Alphacool Eiszapfen extension 20mm G1/4 outer thread to G1/4 inner thread - deep black
The HardTube Project is becoming a reality. Alphacool is setting out on a new path and making great strides! Before now, the most common approach to water cooling was to use normal PVC tubes – now Alphacool is offering a new way to configure your water cooling system. The HardTube variants bring more order into your system, which gives off a more structured impression. The newest are the brass tubes, available in black chrome and chrome, as well as acrylic tubes, carbon, and borosilicate glass. With their fitted connectors and simply-designed functionality, they can be connected to each other with an absolutely tight seal. The PETG-tubes can be bent with the appropriate bending tools in order to fit into any system easily, without needing any additional angled pieces. In order to install the tubes into the system, they need to be sawn to the correct length. PETG tubes can be bent at lower temperatures than acrylic and are generally more flexible and easier to handle. Technical Details: Material: PETG Length: 80cm Scope of delivery: 1x Alphacool Eisrohr 16/13mm PETG 80cm - 4pcs
EK-Quantum Magnitude Accent - Black is an interchangeable aesthetic inner frame for EK's new Magnitude water block. This black accent is best used on Magnitude water blocks with translucent tops where the LED’s shine inwards, or for those without LED implementation. This Magnitude accent is made of anodized aluminum. Available in several different colors and materials, these accent frames are compatible only with EK-Quantum Magnitude CPU water blocks Made in Europe - Slovenia!
Normal 0 21 false false false DE X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Normale Tabelle"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-parent:"; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin-top:0cm; mso-para-margin-right:0cm; mso-para-margin-bottom:8.0pt; mso-para-margin-left:0cm; line-height:107%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri",sans-serif; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi; mso-fareast-language:EN-US;} The Thermaltake Pacific HardTube 45° screw-on nozzle 12mm OD on G1/4 - Black is made of black coloured copper and is especially used for 12mm outer diameter PETG Hardtubes. This way 45° angles can be formed for the cooling circuit.
