The plug in white from Bitspower, can be screwed into a G1/4" internal thread for a certain time or permanently, e.g. to close radiators or equalizing tanks. Technical Data: Material: Brass Colour: White Thread: G1/4" Thread Length: 5 mm
The adapter in matt black from Bitspower has a G1/4" external thread and a G1/4" internal thread. It has an angle of 90 degrees. Technical Data: Material: Brass Colour: Matt Black Angle: 90 ° Thread: G1/4" and inner G1/4" Thread Length : 5 mm
High-End CPU-Wasserkühler von aqua computer, schwarzes Acetalgehäuse, vernickelter Kupferboden, für AMD Sockel AM4/AM5, mit Thermal Grizzly Kryonaut Wärmeleitpaste
The None Chamfer PETG Link Tube in transparent by Bitspower is made of polyethylene terephthalate, PETG for short. This material is a plastic and is used, for example, for PET bottles. Its strength lies in its high break resistance, easy heatability and high stability. In order to implement them in the system, it is necessary to bend them into shape with heat and cut them to size. As a rule, the None Chamfer does not need to be reworked when it is cut. The tube measures 100cm in length, 16mm in outer diameter and 12mm in inner diameter. Only the EML series from Bitspower is compatible as connections. Technical Data: Material: PETG Color: Transparent Outer Diameter: 16 mm Inner Diameter: 12 mm Length: 100 cm Compatibility: EML series Bitspower connectors only
120mm Dual-Radiator von Corsair, Kupfer- und Messing-Aufbau, bis zu vier 120-mm-Lüfter in Push/Pull-Konfiguration, 55 Millimeter Dicke und 13 FPI, 2x G1/4-Anschlüsse
DEMCiflex Dust Filter 120mm Black/White DF0381Toote kirjeldus inglise keeles:Product description:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 120 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Firstly, it is easy to see if cleaning is necessary again - as soon as the white filter fabric has a gray haze, you should do this task. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside of the fan frame. If one of the two arrows points towards the interior, it is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Figure 4 shows an example configuration on a housing (not included). As can be seen, the use of LED fans is possible because the transparent material hardly hampers the lighting. Technical details:Size (frame): 128 x 128 mmSize (filter): 105 x 105 mmCompatibility: 120 mm fan slotMaterial (filter): polyester meshColor: black (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
Funktionaler Fan-, Pumpen- und RGB-LED-Controller, mit separatem LC-Display, bis zu 4 Lüfter mit oder ohne PWM, 4x RGB (12VGRB) & 4x adressierbares RGB (5VDG), inklusive Fernbedienung
The nickel-plated temperature sensor in the colour shiny silver from Bitspower is an easy way to keep an eye on the water temperature of a water cooling system. To do this, the sensor, which has a sealing ring, is screwed into a G1/4" thread, whereby an internal extension then measures the temperature of the surrounding water. With a 90cm long 2-pin cable, the sensor can be connected to a display or control unit or to a compatible motherboard. This allows, for example, the rotation speed of radiator fans to be automatically controlled depending on the water temperature. Technical Data: Material: Nickel-Plated Brass Colour: Shiny Silver Thread: G1/4" Thread Length: 4 mm Sensor Length: 8 mm 2-Pin Cable: 90 cm
DEMCiflex Dust Filter 140mm Black/White DF0382Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 140 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Firstly, it is easy to see if cleaning is necessary again - as soon as the white filter fabric has a gray haze, you should do this task. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside of the fan frame. If one of the two arrows points towards the interior, it is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Figure 4 shows an example configuration on a housing (not included). As can be seen, the use of LED fans is possible because the transparent material hardly hampers the lighting. Technical details:Size (frame): 153 x 153 mmSize (filter): 129 x 129 mmCompatibility: 140 mm fan slotMaterial (filter): polyester meshColor: black (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
Now finally also with us the Black ICE Nemesis radiators The Black Ice® Nemesis® GTR radiators are the next generation of computer radiators from Hardware Labs. These radiators offer an improved cooling performance when using
The adapter for 16mm (AD) Hard Tubes in matt black from Bitspower is especially designed for the connection of two graphics cards with SLI/ Crossfire to bridge the short distance. If two graphics cards are used, two of the adapters are also required. They are sealed with two rubber rings. The adapter is especially well compatible with Bitspower's Crystal Link Tube series. Technical Data: Material: Nickel-Plated Brass Colour: Matt Black Connection: 16 mm (OD) Thread: G1/4" Thread Length: 5 mm
DEMCiflex Dust Filter 120mm White DF0688Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 120 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Firstly, it is easy to see if cleaning is necessary again - as soon as the white filter fabric has a gray haze, you should do this task. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Technical details:Size (frame): 128 x 128 mmSize (filter): 105 x 105 mmCompatibility: 120 mm fan slotMaterial (filter): polyester meshColor: white (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
The Protium reservoir from Singularity Computers is a 200mm tube with a diameter of 60mm. Together with the acrylic attachments, the reservoir reaches a height of 239mm. The tube itself is made of acrylic and has a total of seven G1/4" ports. Technical Data: Dimensions: 60 x 60 x 239 mm (L x W x H) Diameter: 60 mm Material: Acrylic (lid, base, reservoir), Aluminium (retention rings) Color: Black, Transparent Threads: 7x G1/4" Scope of Delivery: 1x 200 mm acrylic reservoir 2x Aluminium retention rings 1x 90° quad port cap (bottom) 1x Triple port cap (cover) 1x 16 mm internal acrylic flow standpipe 5x G1/4" stop fittings 2x Silicone O-rings
Tootekood: ROGSTRIXLCII240ARGBGTIN: 4711081145905Jahutid ja lisad
Water block dimention: 80 x 80 x 45 mm Block Material (CPU Plate): Copper Radiator Dimension: 121 x 272 x 27 mm Radiator Material: Aluminum Tube: Sleeved Rubber tube Tube Length: 380 mm Fan: ROG Designed ARGB Radiator Fan - Size: 2 x Fan Slots (120mm) - Dimension: 120 x 120 x 25 mm - Speed: 800 - 2500 RPM +/- 10% - Static Pressure: 5.0 mmH2O - Air Flow: 80.95 CFM / 137.5 m3h - Noise: 37.6 dB(A) - Control Mode: PWM/ DC AMD: AM4 Package Content: 1 x Liquid Cooler (pre-applied thermal compound) 2 x 120 mm ARGB Radiator Fan 1 x Accessory Pack of Screws and Brackets 1 x Quick Start Guide 1 x USB cable for software control 1 x 1-to-2 Fan Splitter Cable 1 x 1 to 4 ARGB spliter cable
Backplate für GPU-Wasserkühlung, für EK-Quantum Vector Strix RX 6800/6900, aus vernickeltem Aluminium, bietet erhöhte Stabilität, mit Wärmeleitpad für passive Kühlung der PCB-Komponenten
Suurus:120 L x 120 W x 25 H mm tööpinge:4,5-13,8 V testitud:12V õhuvool:69 m3/h õhusurve:1,390 mm/H20 müratase:13,2 dBA kiirus:1000 RPM võimsustarve:0,96 W eestikeelne ülevaade:http://youtu.be/HnuOvu39nqk tootjalehel:http://www.blacknoise.com/en/products/it/17/Noiseblocker-NB_BlackSilentFan_120mm
The None Chamfer PETG Link Tube in transparent by Bitspower is made of polyethylene terephthalate, PETG for short. This material is a plastic and is used, for example, for PET bottles. Its strength lies in its high break resistance, easy heatability and high stability. In order to implement them in the system, it is necessary to bend them into shape with heat and cut them to size. As a rule, the None Chamfer does not need to be reworked when it is cut. The tube measures 100cm in length, 12mm on the outside diameter and 10mm on the inside diameter. Only the EML series from Bitspower is compatible as connections. Technical Data: Material: PETG Color: Transparent Outer Diameter: 12 mm Inner Diameter: 10 mm Length: 100 cm Compatibility: EML series Bitspower connectors only
Full-Block-Wasserkühler von EK Water Blocks, für RTX 3080 und 3090-Grafikkarten im Referenz-Design, schwarzer Acetal-Deckel, Kühlkörper aus hochreinem Kupfer
