All reservoirs of the aqualis series are equipped with a borosilicate glass tube. In contrast to acrylic glass, which is often used for tube reservoirs, borosilicate glass is extremele hard and scratch-resistant, features superb thermal and chemical resistance and a very low thermal expansion. The glass tube of the 450 ml and 880 ml variants has an outer diameter of 75 mm and a wall thickness of 5 mm. Base and top of the aqualis reservoirs are made from Delrin and connected by a stainless steel tube. As a optical highlight, a fountain effect can be realized. If the return line is connected to the center connector of the reservoir, the water flows through the stainless steel tube to the top of the reservoir, where it is ejected through eight nozzles. In combination with illumination, this is a real eye catcher effect. A thin acrylic plate near to the bottom of the reservoir reduces air ingestion to a minimum. Alternatively, the return line can be connected to a lateral connector of the reservoir, the water then exits directly from the base part. For this configuration, a deflector plate is included in delivery to ensure can be installed to effectively remove air from the water circuit. The aqualis PRO 450/880 ml variants additionally feature an acrylic window in the base part and up to six LEDs (5 mm size) can be installed into the base part. The PRO variants can be upgraded with an electronic fill level sensor at a later date. The aqualis XT 450/880 ml variants feature the same acrylic window and LED mounting as the PRO variants. Additionally, the XT variants feature an electronic fill level sensor with USB and aquabus interface, a programmable alarm output and an external temperature sensor input. For monitoring and configuration, the aquasuite software can be downloaded free of charge. In addition to the USB interface, the 4-pin aquabus interface can be used to directly connect the fill level sensor to an aquaero 5 controller (not included in delivery). The alarm output can be configured to be used as a rpm signal to be connected to a fan connector with fault detection (for example motherboard fan headers) or to be used as a switched output for example to connect a LED. Fill level and external temperature sensor input can be configured to raise an alarm. The external temperature sensor input is compatible with all Aqua Computer temperature sensors. All variants are also available with nano coating that will cause water to roll off the inner surface of the borosilicate glass tube. Technical details: Dimensions without stainless steel bracket: approx. 80 x 80 x 290 mm Filling volume: approx. 880 ml Connection threads: G1/4 Scope of delivery: One Reservoir One stainless steel bracket One stainless steel deflector plate Two sealing screws G1/4 (preinstalled) Monting material Please note: Fittings are not included in delivery, please order seperately.
Low-Noise-Pumpe von Alphacool und Laing, Silbernes Messing-Gehäuse (Silver Nickel), möglich, 200 l/h und 2,44 m Förderhöhe bei 10 Watt Leistungsaufnahme, Complete Edition mit Alphacool Eisdecke Aufsatz in Acryl, 5x G1/4-Zoll-Gewinde
120mm Dual-Radiator von Alphacool, Vollkupfer-Aufbau mit schwarzem Stahl-Rahmen, bis zu vier 120-mm-Lüfter in Push/Pull-Konfiguration, 30 Millimeter Dicke und 16 FPI, 2x G1/4-Anschlüsse
The airplex radical series combines some key features from the renowned airplex modularity series in a new design, radically reduced to function and performance. The result is a radiator of excellent quality for a competitive price. Just as the airplex modularity series, no welding is performed during production of the airplex radical series, preventing any welding residues inside the radiator. The coolant does not have contact to any other materials than seals, Delrin, copper and stainless steel.For an improved and easier installation process, the airplex radical series comes with threaded inserts made from nickel plated brass that protrude into the mounting holes of the fans. Therefore, fans are "automatically" correctly aligned to the threads - extremely convenient especially with large radiators! Additionally, this results in a deeper thread and the screw can be positioned farther away from the tubes and fins of the radiator, reducing the risk to damage the radiator by using too long screws. If the radiator is to be installed without fans, the inserts can also be installed upside-down resulting in a nearly flat surface, so there is no gap between radiator and PC case.Both sides of the radiator are equipped with slide rails for the threaded inserts and inserts for one side of the radiator are included in delivery. Additional inserts are available separately. Small notches in the slide rails lock the inserts when installed.The radiator frame is made from stainless steel, the rear is chromated in dark gray for optical purposes. The total dimensions of the radiator are extremely compact in relation to the fin dimensions.Technical details:Dimensions: 160 x 140 x 40 mmConnection threads: G 1/4Threaded inserts: M3Connection terminal material: DelrinTube material: CopperFin material: AluminumFrame material: Stainless steelScope of delivery:One radiator4 threaded inserts M34 screws M3 x 25
Toote kirjeldus inglise keeles:To connect the individual components of the water cooling, the choice of the correct connections and their sufficient number is essential. Otherwise, installation will quickly become a frustrating experience if assembly fails on the wrong or too few connectors and is delayed due to this. Bitspower offers a comprehensive product range that offers the right solution for every requirement - whether adapters, direct hose connections, brackets or distributors. The design is solid and has a sealing ring. Thus, the connections remain tight and ensure high long-term durability. This is a matte black adapter from 1/4 inch outside to 1/4 inch inside thread, which makes it an extension. The connector has a 45 degree angle and can be rotated twice for added flexibility. Note: The turning function of the connections should always be used in the disassembled state, as this is relatively stiff due to the design. When installed, do not apply force to connections to avoid damaging the connectors themselves and the radiators on them. Technical details:Material: brassColor: matt blackConnections: Male Thread: 1/4 inch Female Thread: 1/4 inch
Tootekirjeldus inglise keeles:Create a swiveling 90 degree elbow bend using any Koolance G 1/4 BSPP (parallel) thread fitting. For a basic elbow fitting, the Koolance Coupling Adapter could also be used. Or for maximum adjustment, consider placing two swiveling elbow fittings together. Tube fitting not included.
Product kirjeldus: CORSAIR LL seeria LL120 RGB Dual Light Loop case fan Product Type: Case fan Packaged Quantity: 3 (spetsifikatsioons are for single item) Package Content: Mounting screws for case fans, Corsair Link Lighting Node PRO, RGB lighting hub värv: valge, sinine, kollane, punane, roheline, oranž, violett Fan Diameter: 120 mm Fan kõrgus: 25 mm Fan Bearing: Hydraulic bearing pöördekiirus: 360-2200 pööret minutis õhuvool: 63 cfm müratase: 36 dBA Power ühenduspesa: 4-pin fan connector Features: PWM control, RGB LED x16 mõõtmed (WxDxH): 12 cm x 2.5 cm x 12 cm kaal: 163 g Features: Corsair iCUE Manufacturer Warranty: 2-year garantii
The None Chamfer Brass Hard Tube in the color shiny black from Bitspower, is made of brass. With this durable tube, as well as the stylish color, high quality and unique water cooling can be created. As with other Hard Tubes, the tube can be cut or bent for the WaKü. The latter however with tube bending tool and for experienced hobbyists. As a rule, the None Chamfer does not need to be reworked when it is cut. The tube measures 300mm in length, 12mm in outer diameter and 10.6mm in inner diameter. It has a wall thickness of 0.7mm and is therefore very stable. C47, C48 and the ML series from Bitspower are compatible as connectors. Technical Data: Material: Brass Color: Shiny Black Material Thickness: 0.7 mm Outer Diameter: 12 mm Inner Diameter: 10,60 mm Length: 300 mm Compatibility: C47, C48 & ML series Bitspower connectors only
Tootekood: BP-NCCLT12ACBK-L1000GTIN: 4719552224616Jahutid ja lisad
With the Crystal Link Tubes, Waku specialist Bitspower presents a very interesting solution for water enthusiasts who are not completely unskilled in their craft. These are solid tubes of acrylic plastic, which can be cut by the user to the required length and bent with the aid of a heat source suitable. The resulting possible connection of the individual water cooling parts with longer dead straight sections and exactly curved radii is a visually appealing alternative to the traditional connection by means of hoses dar. For example, if you use a hot air gun and the acrylic tube heated with it for some time, the material is so soft that one It can easily bend into the desired radius and holds as long until the acrylic has cooled and the now bent tube hardens again. It does not get any more individual Everything you need can be created here and even adjusted later. Ideally, in addition to a hot air gun and gloves you have a silicone rod (or something similar flexible, but heat-resistant) to hand, which one pushes into the tube in advance, so that the soft tube gets no kink when bending. The transparent-blue Crystal Link Tube offered here has an outer diameter of 12 mm and an inner diameter of 10 mm. The length is 100 cm. It can be used in conjunction with bit-power adapter fittings from the C47, C48 and ML series. Technical details:Material: acrylic glass (PMMA)Colour blueOuter diameter: 12 mmInner diameter: 10 mmLength: 1,000 mmCompatibility: C47 Series Bit Power Fittings and Adapters C48 Bit Power Fittings and Adapters C48 Series Bit Power Fittings and Adapters
Toote kirjeldus inglise keeles:With the Crystal Link Tubes, Waku specialist Bitspower presents a very interesting solution for water enthusiasts who are not completely unskilled in their craft. These are solid tubes of acrylic plastic, which can be cut by the user to the required length and bent with the aid of a heat source suitable. The resulting possible connection of the individual water cooling parts with longer dead straight sections and exactly curved radii is a visually appealing alternative to the traditional connection by means of hoses dar. For example, if you use a hot air gun and the acrylic tube heated with it for some time, the material is so soft that one It can easily bend into the desired radius and holds as long until the acrylic has cooled and the now bent tube hardens again. It does not get any more individual Everything you need can be created here and even adjusted later. Ideally, in addition to a hot air gun and gloves you have a silicone rod (or something similar flexible, but heat-resistant) to hand, which one pushes into the tube in advance, so that the soft tube gets no kink when bending. The transparent-blue Crystal Link Tube offered here has an outer diameter of 12 mm and an inner diameter of 10 mm. The length is 100 cm. It can be used in conjunction with bit-power adapter fittings from the C47, C48 and ML series. Technical details:Material: acrylic glass (PMMA)Colour transparentOuter diameter: 12 mmInner diameter: 10 mmLength: 500 mmCompatibility: C47 Series Bit Power Fittings and Adapters C48 Bit Power Fittings and Adapters C48 Series Bit Power Fittings and Adapters
The Arctic thermal pads are ideal for efficiently exchanging heat between different components. Thanks to the high quality of workmanship and excellent thermal conductivity, the pads are used in many places on computers and electronic components. The thermal pad, which is based on silicone and a special filler, far outperforms generic and performance-oriented pads. In a test by PC Games Hardware (11/2018), the "excellent processability and reusability in every respect" was praised. In combination with the fair price and good performance, our thermal pad was recommended as a "price-performance tip". Thanks to its low hardness and good compression properties, the thermal pad acts as a perfect gap filler and easily bridges uneven surfaces and air gaps. The ARCTIC Thermal Pads are non-adhesive and can therefore be placed precisely. Installation is child's play and therefore perfect for beginners. The pad contains no metal particles, is electrically insulating and not capacitive. Handling is therefore safe since contact with electrical parts does not lead to damage. Technical specifications: Dimensions 120 x 20mm Contents: 2 pieces Thickness 0.5 mm Thermal conductivity 6.0 W / mK Hardness 25 shore 00 Relative density 3.2 g / cm³ colour blue Operating temperature -40 ~ 200 ℃ Volume resistance 1 X 1012 Ω-cm Interruption voltage 12 KV / mm Draw resistance 2.5 Kgf / cm² Elongation 45% Dielectric constant 14.1816 ε at 60 Hz 13.0264 ε at 1K Hz 13.0264 ε at 1M Hz Flammability V-0
The new Alphacool Eisblock XPX Aurora Edge CPU water cooler offers fantastic performance thanks to the patented ramp design as well as boasting excellent quality. The new Aurora design in combination with the addressable digital RGB illumination offers many possibilities for outstanding illumination of the CPU water block. Performance in abundance! Alphacool already developed and patented new flow technology for the first Alphacool Eisblock XPX series. The so-called "ramp system" ensures an even flow of water inside the cooler and sits in front of the diffuser plate. This ensures that the water is pressed evenly through the diffuser plate, which in turn pushes the water evenly over the cooling base. The cooling channels on the CPU cooler base has also been enlarged to a proud 34 x 32 mm to accommodate the ever-growing CPU DIEs. This is especially true for multi-core processors with 4, 6, 8 or even 12 and more CPU cores. So that the heat from the CPU can be transferred to the water as quickly as possible. 81 cooling fins can be found on the cooling plate to ensure maximum heat diffusion. The fin structure has been reduced to just 0.2 mm in order to create the largest possible surface area in the smallest possible space. And the lighting? All new Eisblock XPX Aurora Edge CPU waterblocks come with addressable digital RGB lighting. The aRGB LEDs are integrated directly into the CPU water cooler and run once around the entire cooling block. With up to 15 digital RGB LEDs the entire CPU block is evenly and intensively lit. Of course, the brightness can be controlled by an appropriate controller. And as with all aRGB LED products all known effects can be created. From simple colour changes to wave effects and rainbow lighting, everything is possible. Of course, the Alphacool Eisblock Aurora coolers can also be connected and controlled via mainboards using the standard 3-pin 5V connector. The cable also has an integrated Y-adapter. This makes it easy to connect further Alphacool Aurora products in series without having to order separate Y-adapters. Extension cables may be needed if you want to connect the products in series, depending on the size of the case. Is installation difficult? Mounting the XPX Aurora Edge Eisblock cooler is simple. The backplate is simply attached to the mainboard from behind. The mounting frame for the AMD or Intel socket is clamped to the cooler and the corresponding mounting screws are pre-attached to this frame. Next, you simply apply thermal paste and you attach the cooler using the screws. Please note: Remove the protective foil on the cooler base before use! Unique Aurora Design The Alphacool Eisblock Aurora Edge has been significantly changed in some points to its predecessor, the Eisblock XPX. The lower part of the cooler is completely made of brass and no longer of plexiglass or transparent nylon. This changes the overall feel and quality of the cooler. Not only is it heavier in the hand, but it is also much more stable than the usual Plexi CPU water coolers. In order to stand out visually from the normal Eisblock XPX Aurora CPU water cooler, the bottom of the cooler was kept completely in black. This emphasizes the visual effect of the water flow. The corners of the CPU cooler are more angular, which makes the cooler stand out from the normal Aurora Plexi Eisblock. Technical details Dimensions (WxTxH): 70 x 70 x 32,5 mm Net weight: 407 g Max working temperature: 60 °C Material cooler: nickel plated copper Material bottom part: brass Material top: Plexi Threads: 2 x G1/4“ Power supply Digital RGB: 3-Pin 5V Pressure tested: 1,5 Bar Certificates: CE, FC, ROHS Download manual PDF: Alphacool Eisblock XPX Aurora Edge - Plexi Black Digital RGB Download data sheet PDF: Alphacool Eisblock XPX Aurora Edge - Plexi Black Digital RGB
HEATKILLER® IVMade from enthusiasts for enthusiasts Now even more powerful: up to 3°C temperature decrease compared to its predecessor – thanks to a completely revised cooling structure Real high flow design: higher flow performance – thanks to bigger jet structure and receptacles Improved reliability: cooling structure without jet plate, jet directly integrated into the cooler now Mounting is a child's play: tool-free Easy-Mount-System Improved fittings compatibility: 16/10 and 19/13 fittings possible – thanks to a thread distance of 25mm Water coolers from the HEATKILLER® CPU series are among the most popular and top-selling CPU water coolers. Ever since the launch of the first HEATKILLER® CPU water cooler in 2001, the series has been constantly improved and optimised. The HEATKILLER® IV presents the most extensive alterations, so far. The focus of innovation was the new cooling structure. Finer micro fins greatly enlarge the contact surface of cooling liquid and cooler. Flow characteristics became optimised as well. These changes increased the cooling performance by up to 3°C compared to the predecessor. The flow efficiency benefits too supported by large-volume receptacles. The HEATKILLER® IV features a real high flow design, making it perfectly suitable also for lower performing pumps. By the way, the new cooling structure completely does without a jet plate. This improves the cooler's reliability because less dust particles can accumulate within the cooling structure. The HEATKILLER® IV also comes up with an improved feature set. This includes the comfortable Easy-Mount-System. After initial installation, the cooler can be mounted or de-mounted tool-free at any time without the need to dismount the mainboard as well. And the mounting brackets do now precisely define the contact pressure, thus mounting errors virtually do not appear. If you prefer big fittings, you will be glad to hear of the enlarged distance between the G 1/4” threads – which is now 25mm. This makes the HEATKILLER® IV compatible with all common thread types, up to the size of 19/13. The HEATKILLER® IV is a product “made in Germany”, manufactured on state-of-the-art CNC machines at the Watercool headquarters. Specifications:Material: Acetal (top), copper (bottom plate), polished stainless steel (brackets), nickel-plated brass ( Easy-Mount-System)Dimensions (L x W x H): 66 x 59 x 17 mmWeight: ca. 450 gSealing: NBR 70Threads: 2x G ¼ inch (DIN ISO 228-1)Thread distance: 25 mmSocket compatibility AMD: 939, 940, AM2, AM2+, AM3, AM3+, FM2, FM2+ Included:HEATKILLER® IV BASIC (AMD processor) ACETAL CLEANMounting material / Manual
The new Alphacool Eisblock XPX Aurora Edge CPU water cooler offers fantastic performance thanks to the patented ramp design as well as boasting excellent quality. The new Aurora design in combination with the addressable digital RGB illumination offers many possibilities for outstanding illumination of the CPU water block. Performance in abundance! Alphacool already developed and patented new flow technology for the first Alphacool Eisblock XPX series. The so-called "ramp system" ensures an even flow of water inside the cooler and sits in front of the diffuser plate. This ensures that the water is pressed evenly through the diffuser plate, which in turn pushes the water evenly over the cooling base. The cooling channels on the CPU cooler base has also been enlarged to a proud 34 x 32 mm to accommodate the ever-growing CPU DIEs. This is especially true for multi-core processors with 4, 6, 8 or even 12 and more CPU cores. So that the heat from the CPU can be transferred to the water as quickly as possible. 81 cooling fins can be found on the cooling plate to ensure maximum heat diffusion. The fin structure has been reduced to just 0.2 mm in order to create the largest possible surface area in the smallest possible space. And the lighting? All new Eisblock XPX Aurora Edge CPU waterblocks come with addressable digital RGB lighting. The aRGB LEDs are integrated directly into the CPU water cooler and run once around the entire cooling block. With up to 15 digital RGB LEDs the entire CPU block is evenly and intensively lit. Of course, the brightness can be controlled by an appropriate controller. And as with all aRGB LED products all known effects can be created. From simple colour changes to wave effects and rainbow lighting, everything is possible. Of course, the Alphacool Eisblock Aurora coolers can also be connected and controlled via mainboards using the standard 3-pin 5V connector. The cable also has an integrated Y-adapter. This makes it easy to connect further Alphacool Aurora products in series without having to order separate Y-adapters. Extension cables may be needed if you want to connect the products in series, depending on the size of the case. Is installation difficult? Mounting the XPX Aurora Edge Eisblock cooler is simple. The backplate is simply attached to the mainboard from behind. The mounting frame for the AMD or Intel socket is clamped to the cooler and the corresponding mounting screws are pre-attached to this frame. Next, you simply apply thermal paste and you attach the cooler using the screws. Please note: Remove the protective foil on the cooler base before use! Unique Aurora Design The Alphacool Eisblock Aurora Edge has been significantly changed in some points to its predecessor, the Eisblock XPX. The lower part of the cooler is completely made of brass and no longer of plexiglass or transparent nylon. This changes the overall feel and quality of the cooler. Not only is it heavier in the hand, but it is also much more stable than the usual Plexi CPU water coolers. In order to stand out visually from the normal Eisblock XPX Aurora CPU water cooler, the bottom of the cooler was kept completely in black. This emphasizes the visual effect of the water flow. The corners of the CPU cooler are more angular, which makes the cooler stand out from the normal Aurora Plexi Eisblock. Technical details Dimensions (WxTxH): 70 x 70 x 32,5 mm Net weight: 407 g Max working temperature: 60 °C Material cooler: nickel plated copper Material bottom part: brass Material top: Plexi Threads: 2 x G1/4“ Power supply Digital RGB: 3-Pin 5V Pressure tested: 1,5 Bar Certificates: CE, FC, ROHS Download manual PDF: Alphacool Eisblock XPX Aurora Edge - Plexi Chrome Digital RGB Download data sheet PDF: Alphacool Eisblock XPX Aurora Edge - Plexi Chrome Digital RGB
Technical Data: Material: Nickel-Plated Brass Colour: Silver Nickel Supported Tube: 16/12 mm Thread: G1/4", male Thread Length: 4,5 mm Outer Diameter (Fitting): 23 mm Installed Height: 19 mm Compatible Soft Tubing: PVC, EPDM, Norprene, Silicone and most other flexible tubes
During the development of the new P14 PWM PST special emphasis was placed on a focused air flow and a high static pressure. The fan guarantees extremely efficient cooling, even with increased air resistance. Therefore, the P14 PWM PST is particularly suitable for use on heat sinks, radiators as well as pinhole and filters. Technical Details Fan: 140 mm, 200 - 1700 rpm (PWM controlled) Air flow: 72.8 CFM / 123.76 m³ / h (@ 1,700 rpm) Noise level: 0.3 sone (@ 1,700 rpm) Static pressure: 2.4 mm H2O (@ 1,700 rpm) Typical voltage: + 12 V DC Starting voltage: 3.9 V DC Cable length: 400 mm Sub PST Cable Length: 50 mm
Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside or inside of the fan frame. If one of the two arrows points towards the interior or if the rotor suspension is aligned with the interior, this is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate.
Alphacool's Eiszapfen series is future-oriented and characterized by excellent workmanship and high flow. Ball valves have always been a flow brake, making life difficult for each pump. Then, Alphacool has developed a ball valve represents no obstacle to a diameter of 10mm. The inside scoop closes absolutely tight, thus preventing further escape of liquid. On both sides all 1/4“ connections with a maximum thread length of 6mm can be screwed. This ball valve is available in two different color versions: Chrome and Deep Black. Technical Details: Dimensions (LxBxW): 35,4 x 36 x 22,7mm Color: Chrome Scope of delivery: Alphacool Eiszapfen 2-way ball valve G1 / 4 - Chrome
Alphacools's fittings go new ways in looks, quality of manufacturing, colours and choice. The inner diameter of these fittings truly deserves the „high flow“ attribute! The first three colours, Chrome, Deep Black and Shiny Copper offer something for every taste. The product matching series are designed to look elegant in every system, highlighting the individual design of the computer. The limits are endless with these Alphacool fittings in combination with Alphacool tubing! With a new process during chromatising the surface finish is completely connected with the brass body, hence ensuring permanent intense colours and peeling of the chrome layer. The Alphacool name in blue lettering on some of the fittings additionally underlines the individuality of these items. Functionality of this connector:This angled adaptor is a true multi-talent. Revolvable in two places, it can cover all angled up to 90°. Alternatively it can be used to displace a connection thread for maximum fitting compatibility or other needs. Technical specifications: Material: Brass, chromatizedColour: Deep Black Dimensions:Length: 52,2mmWidth: D18,1mmHeight: 25mm Extent of delivery:1x Alphacool angled adaptor double 45° revolvable G1/4" outer thread to G1/4" inner thread - Deep Black Reviews:Xtremesystems.comPT-Reviews.pt
The new generation of Alphacool NexXxoS radiators, a name that is known for experience and quality, is here to breathe new life into the radiator market! Everyone who uses watercooling needs a radiator, and everyone has different requirements for the heat exchanger. Naturally, consumers want the product that's best in class. The Alphacool NexXxoS radiators are here to challenge the best in their class, and be crowned the best radiators in every area and size. No more back and forth - with Alphacool NexXxoS radiators, you know what you're getting! Alphacool has been a trendsetter on the scene for developing and improving radiators for years. That's why these models are among the first radiators to really earn the descriptor "full copper"! All the main elements, not just the fins and channels, but also the channel heads are made of copper. Material-wise, this is a big advantage, and one where other radiators fall by the wayside. The Alphacool NexXxoS X-Flow radiators set themselves apart significantly from conventional radiators in their construction. The X-Flow radiators are built for high flow rates. The slanted copper chambers on either side are built identically. This means the water can flow through all the channels at the same time until it flows into the opposite chamber and leaves the radiator. Freedom in the installation is one of the central points on which Alphacool's development department focused. Both copper chambers have three 1/4" threads. That means connections can be attached on the top, bottom and at the front or back (not on the NexXxoS ST30). Fewer angles are needed, which increases the flow rate and offers more options in the installation. Here, too, Alphacool carries the standard sizes of the 120mm series. Different strengths, 30mm, 45mm and 60mm underscore the wide spectrum that these radiators cover. The installation of the radiators, as well as the fans and radiator faceplates, is easy to do with this series: the M3 threads are standard in the radiator sector, affordable and available in all lengths. Even the dreaded mishap of turning the screws in too deeply won't lead to costly damage with this radiator: an inner protective edge stops the screw before it can come into contact with the fins. The fin spacing was chosen so that the radiator could reach its optimal cooling performance even with slow or medium-speed fans. This is not only comfortable in terms of background noise, but also puts no constraints on the choice of fans. All in all, it's where experience and powerful performance meet with a forward-looking approach and sophisticated solutions. Alphacool NexXxoS Radiators - the one tool for all your cooling needs! Technical Specifications: Inner material: mainly copper Casing material: steel side, brass threads, copper chambers Colour: black Dimensions (LxWxH): 477 x 144 x 30mm Radiator size: 3x140mm Connection thread size: 6x 1/4 inch Fan threads: M3 Pressure-tested to: 1.5 bar Scope of Delivery: X-Flow radiator ST30 3x140mm Assembly materials
The Thermaltake Pacific HardTube 45° Connector 12mm OD - Black is made of black coloured copper and is especially used for 12mm outer diameter PETG Hardtubes. This way 45° angles can be formed for the cooling circuit.
