Tootekood: FD-FAN-PRI-AL14-PWM-3PGTIN: 7340172701651Jahutid ja lisad
Dimensions 140x140x25mm, Turns 500-1700rpm, Air flow rate 53.8-143.44m³ / h, Air pressure 0.44-2.38mmH₂O, Volume 15.1-34.1dB (A), Fan bearing LLS, Connection 4-pin PWM, Voltage range 7-12V, Power consumption 2.16W, Special features RGB illuminated, RGB header (3-pin + 5V / DATA / GND), FD-FAN-PRI-AL14-PWM-3P
The HardTube project becomes a reality. Alphacool takes a completely new way and clearly sets!The method most commonly used previously for water cooling systems is normal PVC hoses - now Alphacool offers another approach to water cooling. The Alphacool HardTube again brings more tidiness into the system which makes a much more structured impression.Brand new plexi tubes with the Alphacool HT connectors make installation very simple, they connect completely sealed together. The plexi tube can be adapt to the system with the appropriate bending tool without needing to use additional angles.The following options are available:HardTube 13/10mm plexi Clear 20cm, 40cm, 60cm and 80cmHardTube 16/12mm plexi Clear 20cm, 40cm, 60cm and 80cm(also available in a pack of 4)Note: Due to the made-to-fit pipes, the connections must be plugged straight with a little effort.Scope of delivery:Alphacool HardTube 13/10mm plexi clear 80cm - 4pcsAttention: Not compatible with Monsoon fittings.
The nickel-plated adapter from Bitspower in the color shiny black, has a 90 degree angle and is rotatable. One side is intended for mounting hard tubes with an outside diameter of 12mm and the other side has a G1/4" external thread for mounting on radiators and Co. The two rubber rings seal the sides. Technical Data: Material: Nickel-Plated Brass Colour: Shiny Black Angle: 90° Thread: G1/4 inch Connection: 1x Ø 12 mm
This is the 2nd generation Vector GPU water block from the EK® Quantum Line, designed for EVGA® FTW3 RTX 3070 graphics cards based on the latest NVIDIA® Ampere™ architecture. For a precise compatibility match of this water block, we recommend you refer to the EK Cooling Configurator. An EK Water Block for FTW3 RTX 3070 EK-Quantum Vector FTW3 3070 D-RGB water block is compatible with FTW3 RTX 3070 graphics cards. The Vector water block actively cools the GPU, VRAM, power stages, and chokes in the VRM (voltage regulation module). These newly developed water blocks feature optimized flow paths that reduce hydrodynamic instabilities and vortexing (dead spots) inside of them. The EK-Quantum Vector Series water blocks use an Open Split-Flow cooling engine design, which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, meaning it can be used with weaker water pumps or pumps running on low-speed settings, and still achieve top performance. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performance when used in any given coolant flow orientation. The fin array is populated by 28 microfins with 0.6mm wide microchannels that provide optimal cooling performance, without unnecessary flow restrictions or clogging hazards. The base of the block is CNC-machined out of nickel-plated electrolytic copper, while its top is CNC-machined out of durable POM acetal. These 2nd generation Vector GPU water blocks also feature Acetal terminals. The watertight sealing is ensured by high-quality EPDM O-rings, while brass standoffs are already pre-installed and allow for a safe and easy installation procedure. D-RGB lighting on EK-Quantum Vector FTW3 RTX 3070 D-RGB water block The aesthetic corner end-piece is housing the addressable D-RGB LEDs. This water block boasts a total of 8 individually addressable RGB LEDs, and it is compatible with popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 3-pin D-RGB LED connector is to be aligned with the +5V marking on the D-RGB (addressable) header. Backplate for the EK-Quantum Vector FTW3 3070 water block EK recommends the purchase of a retention backplate, especially for the 3070 models of graphics cards. The backplate improves the overall aesthetics of your graphics cards and also provides additional passive cooling for the GPU core, and backside of the printed circuit board VRM section. Technical Specification Dimensions: (LxHxW) - 314x155x21mm Enclosed EK-Quantum Vector FTW3 RTX 3070 D-RGB series high-performance water block Mounting mechanism with screw-in brass standoffs Necessary mounting screws, nuts, and washers 2x Nickel plated brass plug G1/4” EK-Loop Multi Allen Key (6mm, 8mm, 9mm) Thermal pads Thermal grease EK-TIM Ectotherm (1g)
Schicker zylindrischer Ausgleichsbehälter, Röhre und Aufsätze aus transparentem Acryl, drei Aufsätze für flexible Anschlussmöglichkeiten, schwarze Sicherungsringe aus Aluminium
All-In-One-Wasserkühlung in Weiß, 360-mm-Radiator, drei 120-mm-ARGB-Lüfter, 3 austauschbare Pumpendeckel, Unendlichkeitsspiegel-Effekt, schönes Design und leiser Betrieb, angewinkelte Fittinge frei drehbar, kompatibel zu Sockeln von AMD und Intel (inkl. LGA 1700)
Successor to the award-winning NH-C14, the NH-C14S is an elite class top-flow CPU cooler that is extremely efficient, highly compatible and remarkably adjustable. Thanks to its deeper fin stack and the renowned NF-A14 PWM fan, the single fan NH-C14S provides similar quiet cooling performance to its dual fan predecessor while being even more versatile: With the fan installed on top of the fins, the cooler is compatible with RAM modules of up to 70mm height. With the fan installed underneath the fins, the total height of the cooler is only 115mm, making it suitable for use in many HTPC cases. At the same time, the new offset layout allows it to clear the top PCIe slot on most µATX and ATX motherboards. Topped off with the trusted, pro-grade SecuFirm2™ multi-socket mounting system, Noctua’s proven NT-H1 thermal compound and full 6 years manufacturer’s warranty, the NH-C14S is a premium quality top-flow solution for the highest demands.SobilikProtsessorTüüpJahutiVentilaatori läbimõõt14 cmToetatud protsessoripesadPistikupesa AM2, Pistikupesa AM2+, Pistikupesa AM3, Socket AM3+, Socket FM1, Socket FM2, Socket FM2+, LGA 1151 (Socket H4), LGA 2011-v3 (Socket R)Pöörlemiskiirus (min)300 RPMPöörlemiskiirus (max)1500 RPMMaterjalAlumiinium, VaskPinge12Laius140 mmSügavus163 mmKõrgus115 mmKaal820 gVentilaatori mõõdud (laius x sügavus x kõrgus)140 x 140 x 25 mmMüratase19,2 dB
- Supports Intel LGA1156/1155/1150/1151 processors- Designed for low profile systems at only 45mm tall- Custom quiet 92mm fan for excellent cooling and low noise- Extruded aluminum fins for good heat dissipation- Reinforced back plate design reduces motherboard bending to provide tighter CPU contactSilverStone Technology’s Nitrogon NT09-115X is a slim profile CPU cooler designed for space limited applications that utilizes LGA 1156/1155/1150/1151 platforms. It has an extruded aluminum fins for excellent thermal conductive. In addition, NT09-115X is equipped with a custom PWM 92mm silent fan that is staggered against the aluminum fins for better airflow focus and enhanced heat dissipation. Measuring only 45mm tall, the NT09-115X is a premier choice for slim cases utilizing LGA 1156/1155/1150/1151 processors.SobilikProtsessorTüüpJahutiVentilaatori läbimõõt9,2 cmToetatud protsessoripesadLGA 1150 (Socket H3)Pöörlemiskiirus (min)550 RPMPöörlemiskiirus (max)2500 RPMMüratase (aeglane kiirus)18,5 dBMüratase (suur kiirus)32 dBMinimaalne õhuvool10,34 cfmMaksimaalne õhuvool47 cfmMinimaalne õhusurve0,136 mmH2OMaksimaalne õhusurve2,8 mmH2OVentilaatorite arv1 ventilaator(id)Jahutusvõimsus (TDP)65 WToote värvAlumiinium, MustMaterjalAlumiiniumLaius96 mmSügavus96 mmKõrgus45 mmKaal213,5 g
High-End CPU-Wasserkühler von aqua computer, schwarzes Acetalgehäuse, vernickelter Kupferboden, für AMD Sockel AM4/AM5, mit Thermal Grizzly Kryonaut Wärmeleitpaste
Toote kirjeldus inglise keeles:The eponymous "Wing Boosts", small increases on the impeller intake side, reduce air turbulence. The fan therefore works quieter at higher speeds than conventional fan designs would allow. The triple set offered here consists of three fans including RF receiver, splitter cables and remote control for controlling and synchronizing the three fans included in the set.The features of the Alpenföhn Wing Boost 3 ARGB fan at a glance:- Three 140-millimeter fans with digitally addressable RGB lighting- Hydrodynamic bearing for high performance, quiet operation and long life- Optimized rotor blades deliver the perfect balance between contact pressure and airflow- Speed range from 400 to 1,050 rpm- 4-pin PWM and 3-pin RGB connector- Including RGB and PWM splitter, RF remote control and receiver as well as screws- ASUS Aura, MSI Mystic Light, Gigabyte RGB Fusion and ASRock PolychromeWing Boost 3 ARGB: Powerful 140mm fanThe Wing Boost 3 ARGB is a 140mm PWM-controlled fan that is equally well-suited for mounting on enclosures, processor coolers and radiators. The fan operates in a speed range between 400 and 1,050 revolutions per minute, achieving a delivery volume of 100.6 m³ / h and a static pressure of 2.19 mm H2O.The hydraulic bearing, which reduces friction noise to a minimum, and the rubber decouplers in the fan frame ensure whisper-quiet operation, even at low revs. Under full load, the Wing Boost 3 ARGB produces a maximum noise level of 19 decibels.Addressable RGB LED lighting in the frameThe Alpenföhn Wing Boost 3 ARGB is equipped with digitally addressable RGB LED lighting. The manufacturer has two 16.8-million-color rings integrated into the fan frame, which throws a slight light on the impeller and can be connected via a 3-pin RGB connector to the motherboard or corresponding controllers. The Wing Boost 3 RGB is compatible with ASUS Aura, Gigabyte RGB Fusion, ASRock Polychrome RGB and MSI Mystic Light.In addition to the three fans of the Alpenföhn Wing Boost 3 ARGB model, this kit also includes all the accessories needed to synchronize the PWM signal and the RGB LED lighting of the three fans. The lighting can be controlled via the enclosed remote control.Technical details:- Dimensions: 140 x 140 x 25 mm (W x H x D)- Material: plastic, rubber- Color: black fan, frame), gray (decoupler)- Volume: max. 19 dB (A)- Speed: 400 - 1,050 rpm- Delivery volume: max. 100.6 m³ / h- Static pressure: 2.19 mm H2O- Voltage: 12V- Voltage range: 7 - 13.2 V- Rated power: 1.32 W- Input current: 0.11 A.Connection:- 4-pin PWM- 3-pin RGB (5VDG)- Lighting: RGB (16.8 million colors)Delivery:- 3x Alpenföhn Wing Boost 3 RGB- 12x screws for housing- 12x screws for radiator- 1x RF remote control- 1x RF receiver- 1x RGB splitter- 1x PWM splitter
Connector: 4-pin Voltage Range: 5-12 V Colour: black Size: 21 x 25 x 48 mm Weight: 15 g Fan compatibility: all Noctua 12V PWM and 5V PWM fans, many third party PWM fans Scope of delivery: NA-FC1 controller NA-SC1 3-way splitter cable NA-EC1 input cable NA-AC4 input cable with power supply adaptor Tootjaleht: http://noctua.at/en/na-fc1/specification
Leistungsstarke AIO-Kühlung in Weiß, in Zusammenarbeit mit Roman "der8auer" Hartung, mit 240-mm-Radiator, zwei Wing Boost 3 ARGB High Speed 120-mm-Lüfter, schickes Design & leiser Betrieb, mit Thermal Grizzly Hydronaut Wärmeleitpaste, kompatibel zu vielen AMD & Intel Sockeln
Die R100B Reservoir’s der neuen ANTILA PURE-Serie von RAIJINTEK bieten einzigartige Regenbogen Effekte des A-RGB’s (5 V adressierbar) durch die eingebaute LED-Lichtkappe. Die Lösung befindet sich auf höchstem Niveau für PC-Enthusiasten und kundenspezifische PC-Modder, um ein Super-ARGB-LED-Effekt Wasser-kühlsystem zu erstellen. Die ANTILA PURE-Serie wird aus hochwertigem POM- und Echtglas hergestellt, um eine kristallklare, stabile, leise, leistungsstarke und langlebige Lösung zu bieten. Mit der ANTILA PURE-Serie können PC-Enthusiasten nicht nur ein bemerkenswert, wunderschönes Flüssigkeitskühlsystem bauen, sondern auch extern modulare Upgrades für ihr Gehäuse kombinieren. Eine robuste Montagehalterung bietet dem Benutzer auch eine zuverlässige, richtungsweisende Montagemöglichkeit und eine benutzerfreundliche Installation. Die ANTILA PURE-Serie ist das beste LED-Reservoir für Ihre Wasserkühlung Ihres Systems! Technische Daten: Anzahl: 1 Stück Dimensionen [l×b×h]: 77×77×173 mm Reservoir Dimensionen: 65×65×127 mm Kühlmittel Kapazität: 400 ml Material: POM + Glas + Aluminium + Stahl Material Gewicht: 780 g Schraubgewinde: G 1/4" Addressable LED: 12 LED Rainbow (4pin header, 2510 spec) – Addressable LED LED Control Method: Motherboard RGB HEADER/ Fernbedienung und RJK Control Box LED Input Connector: 4-PIN header (2.5 Crimp) LED Eingangsspannung: 5V
The CORSAIR RS120 case fan delivers powerful cooling performance with its 120 mm diameter and 25 mm height. Featuring a rotation speed that ranges from 420 to 2100 rpm, this fan caters to diverse airflow needs, providing an airflow of 13.3 to 72.8 cfm for efficient cooling. With Pulse-width modulation (PWM) support, it dynamically adjusts speed based on system temperature, ensuring optimal performance while minimizing noise. The fan operates with a noise level between 10 to 36 dBA, making it suitable for silent or high-performance builds. In addition, the RS120 incorporates a zero RPM fan mode for silent operation when cooling is not needed. Its daisy-chain design simplifies cable management in PC builds by enabling multiple fans to be connected seamlessly. With a magnetic dome bearing, it provides longevity and efficient performance, while air pressure of 0.2 to 4.15 mm ensures focused airflow to critical components. The package includes 4 mounting screws for easy installation.
The CORSAIR iCUE Link LX140-R RGB case fan combines functionality with aesthetic appeal, designed to enhance the cooling performance of any system. Featuring a fan diameter of 140 mm and equipped with a magnetic bearing, it ensures durability and quiet operation. The fan operates at a variable rotation speed ranging from 350 to 2000 rpm, allowing for optimized air flow between 13.4 and 90.6 cfm. The innovative reverse blade design provides flexible airflow options, while the dual ring lighting, powered by 18 RGB LEDs, adds visual enhancement to the build. Further enhancing experience, the fan supports Pulse-width modulation (PWM) for dynamic speed adjustments and comes equipped with a Zero RPM fan mode, ensuring silence during lighter loads. The fan also offers a comprehensive 50,000 hours mean time before failure (MTBF), making it a long-lasting component for any setup. With included iCUE Link connectors and a convenient 13.5 cm iCUE Link cable, integration into existing systems is seamless, paving the way for an efficient cooling management solution.
120-mm PWM fan with aluminum framePractical wireless connection for fewer visible cables40 digitally addressable RGB LEDsSpeed and lighting adjustable via Lian Li L-Connect 3 softwareWhisper-quiet cooling with max. 2,300 RPM at 34 dB(A)141.69 m³/h max airflow and 2.66 mmH2O static pressureRubber pads to decouple disturbing vibrationsNote: This fan requires the Lian Li L-Wireless controller. The controller is sold separately.Wireless ARGB Fans for Clean Cable ManagementThe UNI FAN TL Wireless from Lian Li offers an efficient solution for cable management in your PC. With its wireless 2.4 GHz control for lighting effects and fan speed, it requires significantly fewer cables, simplifying the build of this system. The fan offers dual-zone lighting effects and is easy to install.UNI FAN TL Wireless: Simple Installation and Full ControlThe UNI FAN TL Wireless is easy to install and control thanks to the L-Wireless controller. Through the wireless connection, you control both the RGB lighting and the fan speed directly from your motherboard without the need for extra cables.Customizable Display and Quiet PerformanceThanks to the Fluid Dynamic Bearing (FDB) technology, the Lian Li UNI FAN TL Wireless runs quietly and efficiently, even at high speeds of up to 2,300 RPM. This provides powerful cooling and an aesthetically pleasing solution for your PC, making traditional fans fade in the light of UNI FAN TL Wireless.Reverse Blade for Clean Look and More PerformanceAre you looking for a solution to optimize airflow in your PC while also improving the aesthetics of your fans? With a Reverse Blade fan, you choose a fan blade shape that directs airflow in the opposite direction.Your advantage: The look is the same with every fan. Gone are the days of having to mount fans with the back side against the case to pull in fresh air. This keeps your system cool and incredibly quiet, even under heavy applications!
