Jahutid ja lisad

Arctic BioniX F120 (Gray)

ARCTIC P14 PWM PST CO. Sobilik: Arvuti korpus, Tüüp: Jahuti, Ventilaatori läbimõõt: 14 cm. Toote värv: Must, Ventilaatorite arv: 1 ventilaator(id), Ventilaatori konnektor: 4-pin + 4-pin. Võimsustarve (tüüpiline): 1,44 W, Pinge: 12 ...

Arctic BioniX P140 (Gray)

DEMCiflex Dust Filter 200mm Round Black DF0020Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 180 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside or inside of the fan frame. If one of the two arrows points towards the interior or if the rotor suspension is aligned with the interior, this is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Technical details:Size (frame): Ø approx. 200 mmSize (filter): Ø approx. 175 mmCompatibility: 180 mm fan slotMaterial (filter): polyester meshColor: black (frame), black (filter)Assembly: mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric

Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside or inside of the fan frame. If one of the two arrows points towards the interior or if the rotor suspension is aligned with the interior, this is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate.

Toote kirjeldus inglise keeles:The Alphacool Cape Coolplex reservoirs have been well-known and popular on the water cooling market for years!But even such great products can sometimes use an update to fulfill even the most recent demands. Hence we at Alphacool have let the old series run out and now introduce the new series with POM end pieces as “LT” and now even with solid metal end pieces as the “Copper Edition”. Of course the tubes are made from high-grade Plexiglas which has proven itself with safe operation in many cooling systems for many years!The changes made are subtle but very well thought through:Besides the new materials and surface finishes the top piece of the reservoirs is now equipped with an additional thread, making them great for installation of a Fillport. Additionally the reservoir can now also be installed horizontally! The riser tube is now removable for applications where the top of the reservoir is used as an inlet.A nice side effect: Now even more lighting modules can be installed for beautiful lighting effects.To round off the new concept the screw plugs on all versions now have an elegant polished copper surface finish!For maximum compatibility all threads are G1/4” in size. The proven transparent mounts are now also included again for almost invisible mounting. Make your PC a piece of art with the new Cape Coolplex reservoirs!Technical specifications:- Material: POM, Plexi- Height: 100mm- Diameter: 50mmReviews:- Connection threads: G1/4"- Weight: 264gExtent of delivery:- Reservoir- 2x Mounting clamps- 2 x G1/4" Screw plugsPlease note: For mounting additional screws are needed. We recommend ordering item No. 15705 with this reservoir.Weight & dimensionsWidth 50 mmDepth 50 mmHeight 100 mmDesignMaterial Polyoxymethylene (POM)Colour of product Black, Transparent

DEMCiflex Dust Filter 140mm Black/White DF0382Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 140 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Firstly, it is easy to see if cleaning is necessary again - as soon as the white filter fabric has a gray haze, you should do this task. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside of the fan frame. If one of the two arrows points towards the interior, it is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Figure 4 shows an example configuration on a housing (not included). As can be seen, the use of LED fans is possible because the transparent material hardly hampers the lighting. Technical details:Size (frame): 153 x 153 mmSize (filter): 129 x 129 mmCompatibility: 140 mm fan slotMaterial (filter): polyester meshColor: black (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric

DEMCiflex Dust Filter 120mm Round Black/White DF0525Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 120 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Firstly, it is easy to see if cleaning is necessary again - as soon as the white filter fabric has a gray haze, you should do this task. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside of the fan frame. If one of the two arrows points towards the interior, it is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Figure 4 shows an example configuration on a housing (not included). As can be seen, the use of LED fans is possible because the transparent material hardly hampers the lighting. Technical details:Size (frame): Ø approx. 138 mmSize (filter): Ø approx. 113 mmCompatibility: 120 mm fan slotMaterial (filter): polyester meshColor: black (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric

Alphacools HardTube family does get an additional sibling. The new HardTubes made out of borosilicate glass certainly bring a new level of quality into every system. The previous method that has been most commonly used for water cooling systems is normal PVC hoses - now Alphacool introduces a new approach to water cooling. The Alphacool HardTube additionally brings more tidiness into the system which enables a further structured impression. Borosilicate glass ticks every box on the checking list for watercooling systems. Stability and a brilliant appearance are not the only qualities that should lead to chosing this glass as even most chemicals and temperature flactuations can not harm the borosilicate glass. The whole chemical industry is depending on this glass and we can certainly say that this is not without reason. All glass tubes are compatible with the Alphacool HardTube connectors. Alphacool currently offers two classical sizes. One tube with a 16mm outer diameter and another with 13mm outer diameter. Further different length with 90° angles are introduced as its not possible to personally deform these tubes. To cut the tubes for the preferred length Alphacool recommends using a diamand cutting disc for the Dremel®.(Additionally availaible in our product line: Diamant cutting disc - Art.No: 1012316, Dremel® - Art.No: 32196 and 32229) The following options are available: HardTube borosilicate glass 13/10mm 90° 10/30cm and 20/40cm HardTube borosilicate glass 13/10mm 40cm and 60cm HardTube borosilicate glass 16/11mm 90° 10/30cm and 20/40cm HardTube borosilicate glass 16/11mm 40cm and 60cm Scope of delivery: 1x HardTube borosilicate glass 16/11mm 90° 10/30cm WARNING:Do not under any circumstances use the usual glass tube cutter to shorten the borosilicate glass tube. Borosilicate glass is a solid glass which can not be cut properly with a normal glas tube cutter. Please refer to a Dremel® with the needed cutting disc. Note:Due to the made-to-fit pipes, the connections must be plugged straight with a little effort. Attention:This article is not compatible with Monsoon fittings. Der8auer: Extremely Expensive Hardtubes and DIY Glass-Cutter

Alphacool HF 13/10 connector (62362)

Alphacools's fittings go new ways in looks, quality of manufacturing, colours and choice. The inner diameter of these fittings truly deserves the „high flow“ attribute! The first three colours, Chrome, Deep Black and Shiny Copper offer something for every taste. The product matching series are designed to look elegant in every system, highlighting the individual design of the computer. The limits are endless with these Alphacool fittings in combination with Alphacool tubing! With a new process during chromatising the surface finish is completely connected with the brass body, hence ensuring permanent intense colours and peeling of the chrome layer. The Alphacool name in blue lettering on some of the fittings additionally underlines the individuality of these items. Functionality of this connectorThis manifold is very practical and offers many advantages thanks to its innovative design: Barely any thread length restrictions, almost no flow resistance and mounting possibilities are aplenty. The best thing: This manifold even offers 5 In- respectively outlets. Technical specifications Material: Brass Colour: Deep Black Dimensions Length: 45mm Width: 17mm Height: 17mm Extent of delivery 1 x Alphacool HF 5-way connection terminal G1/4 inner thread - Deep Black

Alphacool’s Eiszapfen Connector Series is the high-end execution of these tried-and-true connectors! Every requirement you could have of a connector is met with this series: highflow, form, processing and colour. A refusal to compromise in development and production has made the Eiszapfen series into what it is. Components are available in brilliant chrome or a deep, matte black, which will fit excellently into any system. A special procedure binds the outer coating firmly to the surface, improving the longevity of the intense colour and preventing any chipping or peeling of the coating. Every connector now has the Alphacool logo, which along with their distinctive shape makes them unmistakable! Anyone looking for colourful options has them: the O-rings in the shipment come in three colours. With the available UV-light option, these will even light up in the corresponding colour. Model: Extension 20mmThis slim adapter extends a ¼” thread by 20mm. This is mainly useful where a ¼” track is hard to reach or sits too far in. Technical Specifications: Material: Brass Colour: Chrome Dimensions: Length: 20mm Diameter: 18mm Scope of Delivery: 1x Alphacool Eiszapfen extension 20mm G1/4 outer thread to G1/4 inner thread - chrome

500-mm-Tube von Bitspower, hergestellt aus hochwertigem Messing, zum Verbinden von Wakü-Komponenten, 16 mm Außendurchmesser, Blau (Royal Blue)

Vernickelter Wasserkühler (Mosfets) von Bitspower, für ASUS ROG Dominus Extreme-Mainboards, Copper Limited Edition mit massivem Kupferdeckel

Vernickelter Wasserkühler (Mosfets) von Bitspower, für ASUS ROG Dominus Extreme-Mainboards, mit adressierbarer RGB-Beleuchtung (3-Pin/5V)

The new Alphacool NexXxos radiators, a name that stands for experience and quality has come to bring a fresh breeze to the radiator market.Every user of a water cooling system needs a radiator and everyone has different requirements towards the heat exchanger. Of course the customer always demands the best in its class. The Alphacool NexXxos radiators have come to compete with and to beat the best in their class and to be the best radiator in all sizes. No more endless choices without a clear class leader, the Alphacool NexXxos is the one tool for all your needs!Alphacool has been the company to introduce new developments and improvements in the radiator and water cooling sector generally many times over the last years.Following this tradition, the new NexXxos radiators are the first to truly deserve the “Full copper” attribute. All main parts, not only the fins and channels, but the chambers are also made from copper. This brings an improvement in performance where other radiators are left without a chance. The material already gives an advantage over the competition and the inner structure is up to par with the competition. Separated chambers give the coolant a clear direction, allowing high flow rates which improve the performance of the whole cooling loop.Flat chambers on the heat exchanger increase mounting flexibility thanks to the reduced overall length.Versatile and easy mounting is one of the main points, on which the research and development department at Alphacool focused. The chamber offers three possibilities for fitting installation on both inlet and outlet (not on the NexXos ST30). Less angled fittings are needed, improving flow rates and offering more mounting possibilities. Hence the radiator can even be installed in tight enclosures, where otherwise internal installation is not a possibility. A 1/4" screw plug allows easy de-aeration of the radiator (on all UT60 and NexXxos Monsta) and hassle-free vertical installation of the heat exchanger. The threaded opening can even be used for filling, e.g. in combination with a Fillport.Versatility is the essence of the new NexXxos series! The radiators are available in different versions to be used with 120mm, 140mm or 180mm fans and are available in different thicknesses. The choice of 30mm, 45mm and 60mm offers the perfect radiator for every purpose. Even mounting and installation of fans and radiator grills is easy and versatile with these radiators: The M3 threads are standard in the radiator sector and available in all lengths at an affordable price.Even the dreaded insertion of a screw too far into the radiator does not result in expensive damage. Unlike other radiators, the NexXxos series is equipped with an internal protective ledge which stops the screw before it damages the fins.Fin spacing is always an important factor in radiator design. The new series from Alphacool has a fin design which allows it to perform extremely well even with slow-spinning and medium-speed fans. This is not only pleasant thanks to the fact that it avoids unnecessary noise; it also means that the choice of fans that can be used with these radiators is not restricted.These radiators are the result of experience and powerful performance meeting future-oriented design and well-thought through solutions.Alphacool NexXxos radiators: The one tool for all your cooling needs! Technical dataDimensions (L x W x H)466 x 144 x 45mmQuantity of cooling channels28Cooling channelsCopperColorblackFan threadM3Number of fans3Connection6x G1/4"SlatsCopperThickness39 - 49mmHousingSteelManufacturerAlphacoolFins per inch12Pressure tested2 barFan size140mm

Dimensions 91.5x66x91.5mm (WxHxD) - Fan(s) 1x 60x60x25mm, 1600-8000rpm, 14.86-74.32m³/​h, 16.8-51dB(A) - Weight 590g - Connector 4-Pin PWM - Socket 2011, 2011-3, 2066 - TDP-Class 165W

The new Alphacool NexXxos radiators, a name that stands for experience and quality has come to bring a fresh breeze to the radiator market.Every user of a water cooling system needs a radiator and everyone has different requirements towards the heat exchanger. Of course the customer always demands the best in its class. The Alphacool NexXxos radiators have come to compete with and to beat the best in their class and to be the best radiator in all sizes. No more endless choices without a clear class leader, the Alphacool NexXxos is the one tool for all your needs!Alphacool has been the company to introduce new developments and improvements in the radiator and water cooling sector generally many times over the last years.Following this tradition, the new NexXxos radiators are the first to truly deserve the “Full copper” attribute. All main parts, not only the fins and channels, but the chambers are also made from copper. This brings an improvement in performance where other radiators are left without a chance. In structure, the Alphacool NexXxoS X-Flow Radiators differentiate materially from the standard radiators. The X.Flow Radiators are designet for high flow rates. The bevelled copper chambers on both sides have an identical structure. This Water is jetting at the same time through all avialable channels to the other chamber to whitch it then leaves the radiator.Versatile and easy mounting is one of the main points, on which the research and development department at Alphacool focused. The chamber offers three possibilities for fitting installation on both inlet and outlet (not on the NexXos ST30). Less angled fittings are needed, improving flow rates and offering more mounting possibilities.Here, too, Alphacool provides the popular sizes of the 120mm series. Different thicknesses, 30mm, 45mm and 60 mm underscore the broad spectrum that cover these radiators. Even mounting and installation of fans and radiator grills is easy and versatile with these radiators: The M3 threads are standard in the radiator sector and available in all lengths at an affordable price.Even the dreaded insertion of a screw too far into the radiator does not result in expensive damage. Unlike other radiators, the NexXxos series is equipped with an internal protective ledge which stops the screw before it damages the fins.Fin spacing is always an important factor in radiator design. The new series from Alphacool has a fin design which allows it to perform extremely well even with slow-spinning and medium-speed fans. This is not only pleasant thanks to the fact that it avoids unnecessary noise; it also means that the choice of fans that can be used with these radiators is not restricted.These radiators are the result of experience and powerful performance meeting future-oriented design and well-thought through solutions.Alphacool NexXxos radiators: The one tool for all your cooling needs! Technical dataDimensions (L x W x H)532 x 124 x 60mmQuantity of cooling channels36Thickness49 - 69mmKühlkanäleCopperColorblackFan threadM3Connection6x G1/4"SlatsCopperFan size120mmHousingSteelPressure tested0,8 barManufacturerAlphacoolNumber of fans4Fins per inch10

For perfect bends in the Alphacool HardTubes now there is the perfect solution. Simply insert the silicone inside the HardTube and heat the desired location. Thanks to the extremely heat-resistant silicone the pipe can be bent without the curved point kinking. After cooling, the silicone can be easily removed. Available for HardTubes with 10mm and 12mm inner diameter in each 30cm length for curves in short pipes and 100cm length for curves in longer pipes. Technical Data Length: 100cm Thickness: 9.2mm Color: blue Scope of delivery 1x Alphacool Silicon Insert 100cm NoticeDue to the manufacturing process, the diameter can vary by 0.5 - 1mm.

Full-Block-Wasserkühler von EK Water Blocks, für RTX 3080 und 3090-Grafikkarten im Referenz-Design, schwarzer Acetal-Deckel, Kühlkörper aus hochreinem Kupfer

Aluminium-Backplate in Silber, für EVGA XC3 RTX 3080/3090-Grafikkarten mit EK-Quantum Vector-Kühler

EK-Quantum Vector Strix RTX 3080/3090 Backplate - Nickel is a CNC-milled backplate made of nickel-plated aluminium that fits all EK-Quantum Vector Strix RTX 3070/3080/3090 water blocks. The backplate covers the full length of the graphics card PCB, serves as an aesthetic addition and also provides passive cooling for the back of the voltage regulator module (VRM), the GPU core and the VRAM on the 3090 cards. Enclosed: EK-Quantum Vector Strix RTX 3070/3080/3090 back plate - nickel Assembly mechanism Thermal pads

The EK-Quantum Vector Strix RTX 3070 D-RGB from EK is a complete cooler for the graphics card of the ROG Strix RTX 3070 from ASUS. The high-quality workmanship and the nickel-plated copper material used for the heat sink are striking. The copper covers all important areas of the graphics card, such as GPU, memory and voltage converter. The optimised channel structure provides very efficient and reliable cooling. Visually, the cooler is rounded off with a black acetal lid and has four G1/4" connections. But there's more: an addressable D-RGB strip is also integrated, which provides a little illumination even on dark gaming days. The graphics card cooler is compatible with the common RGB synchronisation technologies of all major mainboard manufacturers. Technical Data Material: Nickel-Plated Copper (bottom), Acetal (cover) Color: Black Thread: 4x G1/4" D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground) D-RGB LED count: 6 D-RGB cable length: 500mm Compatibility Asus ROG Strix RTX 3070 Scope of Delivery EK-Quantum Vector Strix RTX 3070 D-RGB series high-performance water block Mounting mechanism with screw-in brass standoffs Necessary mounting screws, nuts, and washers 2x Nickel plated brass plug G1/4” EK-Loop Multi Allen Key (6mm, 8mm, 9mm) Thermal pads Thermal grease EK-TIM Ectotherm (1g)

Effizienter und stylisher 120er Universal-Lüfter im Triplepack, mit 6-Pin-Anschluss (Adapter inkl.), adressierbare RGB-LED-Beleuchtung, 1.000 U/min, 17,5 dB(A), 1,68 mmH2O, hydraulisches Lager, inkl. Controller und Fernbedienung

Leistungsstarker CPU-Kühler von Aerocool, integrierte digital adressierbare RGB-Beleuchtung, ein 120-mm-PWM-Lüfter mit ARGB-LEDs, TDP von 145 Watt, hohe Kompatibilität zu Intel- und AMD-Sockeln

Set aus vier Clips für die Befestigung von Lüftern an CPU-Kühlern, geeignet für die QF90-Lüfter von Cryorig

Thermaltake's Pure A12 is a PWM controlled LED fan that comes in four different colours: blue, green, red and white. Especially radiators benefit from the very quiet operation and low heat generation thanks to the self-lubricating hydraulic bearing. The anti-vibration pads also ensure low noise levels. As the sealing cap prevents the lubricant from escaping, a long service life is also guaranteed. The nine LEDs of the fan impress with a uniform brightness and high colour intensity and give the PC system the final touch. Technical Data: LED colour: Green Dimenson: 120 x 120 x 25 mm Interface: 4-Pin PWM Fan Stated Voltage: 9.0 V Fan Rated Voltage: 12 V Rated current: 0.15 A Power Input: 1.8 W Fan Speed: 500 - 1500 rpm Max. Air Pressure: 1.59 mm-H2O Max Air Flow: 56.45 CFM Noise: 25.8 dB-A Bearing Type: Hydraulic Bearing Life Expectation: 40,000 hrs, 25℃ Weight: 156 g

Iceberg IceFLOE T95 ICEFLOE95-00A

PWM-Lüfter-Hub, mit 10 4-Pin-Steckern, PWM-Signal vom Mainboard, Stromversorgung per SATA- oder Molex-Kabel

The Barrow Manual air tightness tester is designed to test liquid cooling systems without water. With the G1/4" fitting the tester can be connected directly to the system. This is fast and safe. With the pump air is pumped into the circuit, so that in case of possible leakage no components on the PC are damaged by cooling liquid. With the built-in pressure gauge, the pressure can be read precisely. Technical Data Color: Black Threads: G1/4" external thread Weight: 240,8g Maximum Pressure: 1 Bar Scope of Delivery Barrow Manual air tightness tester

The nickel-plated adapter in the color shiny silver couples two tubes, which do not run on a common straight line and provides at the adapter for a bend of 90 degrees. Two rubber rings seal both sides. The adapter is especially well compatible with the Crystal Link Tubes from Bitspower. Technical Data: Material: Nickel-Plated Brass Colour: Shiny Silver Angle: 90 ° Connections: 2x Ø 12 mm

Now finally also with us the Black ICE Nemesis radiators The Black Ice® Nemesis® GTR radiators are the next generation of computer radiators from Hardware Labs. These radiators offer an improved cooling performance when using

Now finally also with us the Black ICE Nemesis radiators. The Black Ice® Nemesis® GTX radiators are the next generation of computer radiators from Hardware Labs. These radiators offer an improved cooling performance when using

Alphacools HardTube family does get an additional sibling. The new HardTubes made out of borosilicate glass certainly bring a new level of quality into every system. The previous method that has been most commonly used for water cooling systems is normal PVC hoses - now Alphacool introduces a new approach to water cooling. The Alphacool HardTube additionally brings more tidiness into the system which enables a further structured impression. Borosilicate glass ticks every box on the checking list for watercooling systems. Stability and a brilliant appearance are not the only qualities that should lead to chosing this glass as even most chemicals and temperature flactuations can not harm the borosilicate glass. The whole chemical industry is depending on this glass and we can certainly say that this is not without reason. All glass tubes are compatible with the Alphacool HardTube connectors. Alphacool currently offers two classical sizes. One tube with a 16mm outer diameter and another with 13mm outer diameter. Further different length with 90° angles are introduced as its not possible to personally deform these tubes. To cut the tubes for the preferred length Alphacool recommends using a diamand cutting disc for the Dremel®. (Additionally availaible in our product line: Diamant cutting disc - Art.No: 1012316 , Dremel® - Art.No: 32196 and 32229 ) The following options are available: HardTube borosilicate glass 13/10mm 90° 10/30cm and 20/40cm HardTube borosilicate glass 13/10mm 40cm and 60cm HardTube borosilicate glass 16/11mm 90° 10/30cm and 20/40cm HardTube borosilicate glass 16/11mm 40cm and 60cm Scope of delivery: 1x HardTube borosilicate glass 16/11mm 90° 20/40cm WARNING: Do not under any circumstances use the usual glass tube cutter to shorten the borosilicate glass tube. Borosilicate glass is a solid glass which can not be cut properly with a normal glas tube cutter. Please refer to a Dremel® with the needed cutting disc. Note: Due to the made-to-fit pipes, the connections must be plugged straight with a little effort. Attention: This article is not compatible with Monsoon fittings. Der8auer: Extremely Expensive Hardtubes and DIY Glass-Cutter

Backplate von Cryorig, für R1/C1/H5 und A-Serie-Wasserkühler, inklusive Multiseg-Bars

The retention rings attach the tops to both ends of the acrylic tubes. As they are included as standard with the Protium reservoirs, this item serves as a replacement or to replace rings of a different colour. Technische Details Material: Aluminium Colour: Black Compatibility: Protium series Scope of delivery 2x retention ring

The retention rings attach the tops to both ends of the acrylic tubes. As they are included as standard with the Protium reservoirs, this item serves as a replacement or to exchange rings of a different colour. Technische Details Material: Aluminium Colour: Silver Compatibility: Protium series Scope of delivery 2x retention ring

The Protium expansion tank from Singularity Computers is a 100mm tube with a diameter of 60mm. Together with the acrylic attachments, the expansion tank reaches a height of 139mm. It has a total of seven G1/4" ports and the tube itself is made of acrylic. Technical Data: Dimensions: 60 x 60 x 139 mm (L x W x H) Diameter: 60 mm Material: Acrylic (lid, base, reservoir), Aluminium (retention rings) Color: Black, Transparent Threads: 7x G1/4" Scope of Delivery: 1x 100 mm acrylic reservoir 2x Aluminium retention rings 1x 90° quad port cap (bottom) 1x Triple port cap (cover) 1x 16 mm internal acrylic flow standpipe 5x G1/4" stop fittings 2x Silicone O-rings