EK-Quantum Vector Strix RTX 3070 D-RGB from EK is a complete cooler for the ROG Strix RTX 3070 from ASUS. The high-quality workmanship and the nickel-plated copper material used for the heat sink are striking. The nickel-plated copper covers all important areas of the graphics card, such as GPU, memory and voltage converter. The optimised channel structure results in very efficient and reliable cooling. Visually, the cooler is rounded off with a transparent acrylic glass lid and a black end piece. The integrated RGB lighting sets the scene perfectly for the EK Quantum. In addition, the cooler has four G1/4" connections. The graphics card cooler is compatible with the common RGB synchronisation technologies of all major mainboard manufacturers. Technical Data Dimensions: 293 x 154 x 16,5 mm Material Base: Nickel-Plated Copper Material Cover: Acryl Thread: 4x G1/4" D-RGB cable length: 500mm D-RGB LED count: 6 D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground) Compatibility ASUS ROG Strix RTX 3070 Scope of Delivery EK-Quantum Vector Strix RTX 3070 D-RGB series high-performance water block Mounting mechanism with screw-in brass standoffs Necessary mounting screws, nuts, and washers 2x Nickel plated brass plug G1/4” EK-Loop Multi Allen Key (6mm, 8mm, 9mm) Thermal pads Thermal grease EK-TIM Ectotherm (1g)
With the HEATKILLER® V, Watercool is starting a new generation of coolers for the current Nvidia RTX 30 graphics cards. Equipped with unique highlights, the current version of the HEATKILLER® V presents what is technically feasible. With an increased number of cooling fins, the cooling performance is increased directly above the graphics processor and thus the most important area is improved. The radiator base, milled from a solid block, establishes contact with all relevant components. The trend-setting dual-layer inflow distributes the water simultaneously on two levels. This ensures an air flow that is at least 30 percent higher than that of our previous generation. The broad and symmetrical flow paths reduce dead spots (standing water) to a minimum and accelerate the flow. The overall result increases not only the maximum cooling capacity but also the flow rate of the HEATKILLER® V. Thanks to the newly designed spacers made of high-performance plastic (PEEK), the 10mm solid copper block is ideally isolated from the circuit board. In addition to the technical innovations, the design of the cooler is also impressive. The screwless cover makes the entire block look like it was cast from a single source. The symmetrically designed channels underline the look of the cooler and make it a unique eye-catcher. The integrated aRGB strips are now standard in combination with the nickel-acrylic variants. This means that the HEATKILLER® V can be perfectly integrated into the lighting concept of the computer. Technical specifications: Base plate material: nickel-plated electrolyte copper Material cover: acrylic glass Cover material: annealed stainless steel Connection terminal material: Acetal Dimensions: (LxWxH): 230 x 119 x 21 mm Connection: 4x G ¼ inch (DIN ISO 228-1) Weight: Pressure tested: 2 bar Compatibility: Nvidia Geforce RTX 3080/3090 Scope of delivery: 1x HEATKILLER® V 1x HEATKILLER® LED Strip aRGB 1x mounting material Thermal Grizzly Kryonaut thermal paste
With the HEATKILLER® V, Watercool is starting a new generation of coolers for the current Nvidia RTX 30 graphics cards. Equipped with unique highlights, the current version of the HEATKILLER® V presents what is technically feasible. With an increased number of cooling fins, the cooling performance is increased directly above the graphics processor and thus the most important area is improved. The radiator base, milled from a solid block, establishes contact with all relevant components. The trend-setting dual-layer inflow distributes the water simultaneously on two levels. This ensures an air flow that is at least 30 percent higher than that of our previous generation. The broad and symmetrical flow paths reduce dead spots (standing water) to a minimum and accelerate the flow. The overall result increases not only the maximum cooling capacity but also the flow rate of the HEATKILLER® V. Thanks to the newly designed spacers made of high-performance plastic (PEEK), the 10mm solid copper block is ideally isolated from the circuit board. In addition to the technical innovations, the design of the cooler is also impressive. The screwless cover makes the entire block look like it was cast from a single source. The symmetrically designed channels underline the look of the cooler and make it a unique eye-catcher. Technical specifications: Base plate material: electrolyte copper Material cover: acetal Connection terminal material: Acetal Dimensions: (LxWxH): 230 x 119 x 21 mm Connection: 4x G ¼ inch (DIN ISO 228-1) Weight: Pressure tested: 2 bar Compatibility: Nvidia Geforce RTX 3080/3090 Scope of delivery: 1x HEATKILLER® V 1x mounting material Thermal Grizzly Kryonaut thermal paste
Kampaania: ASUS Cashback Osta ja registreeri kampaania toode kuni 13.11.2022. Registreerimise taotluse kinnitamine võib kesta kuni 41 päeva pärast kampaania lõppu. Kampaania: Täpsemad tingimused ASUS kampaanialehelt
With the HEATKILLER® V, Watercool is starting a new generation of coolers for the current Nvidia RTX 30 graphics cards. Equipped with unique highlights, the current version of the HEATKILLER® V presents what is technically feasible. With an increased number of cooling fins, the cooling performance is increased directly above the graphics processor and thus the most important area is improved. The radiator base, milled from a solid block, establishes contact with all relevant components. The trend-setting dual-layer inflow distributes the water simultaneously on two levels. This ensures an air flow that is at least 30 percent higher than that of our previous generation. The broad and symmetrical flow paths reduce dead spots (standing water) to a minimum and accelerate the flow. The overall result increases not only the maximum cooling capacity but also the flow rate of the HEATKILLER® V. Thanks to the newly designed spacers made of high-performance plastic (PEEK), the 10mm solid copper block is ideally isolated from the circuit board. In addition to the technical innovations, the design of the cooler is also impressive. The screwless cover makes the entire block look like it was cast from a single source. The symmetrically designed channels underline the look of the cooler and make it a unique eye-catcher. Technical specifications: Base plate material: electrolyte copper Material cover: acrylic glass Cover material: black anodized aluminum Connection terminal material: Acetal Dimensions: (LxWxH): 230 x 119 x 21 mm Connection: 4x G ¼ inch (DIN ISO 228-1) Weight: Pressure tested: 2 bar Compatibility: Nvidia Geforce RTX 3080/3090 Scope of delivery: 1x HEATKILLER® V 1x mounting material Thermal Grizzly Kryonaut thermal paste
With the HEATKILLER® V, Watercool is starting a new generation of coolers for the current Nvidia RTX 30 graphics cards. Equipped with unique highlights, the current version of the HEATKILLER® V presents what is technically feasible. With an increased number of cooling fins, the cooling performance is increased directly above the graphics processor and thus the most important area is improved. The radiator base, milled from a solid block, establishes contact with all relevant components. The trend-setting dual-layer inflow distributes the water simultaneously on two levels. This ensures an air flow that is at least 30 percent higher than that of our previous generation. The broad and symmetrical flow paths reduce dead spots (standing water) to a minimum and accelerate the flow. The overall result increases not only the maximum cooling capacity but also the flow rate of the HEATKILLER® V. Thanks to the newly designed spacers made of high-performance plastic (PEEK), the 10mm solid copper block is ideally isolated from the circuit board. In addition to the technical innovations, the design of the cooler is also impressive. The screwless cover makes the entire block look like it was cast from a single source. The symmetrically designed channels underline the look of the cooler and make it a unique eye-catcher. Technical specifications: Base plate material: electrolyte copper Material cover: acrylic glass Cover material: annealed stainless steel Connection terminal material: Acetal Dimensions: (LxWxH): 230 x 119 x 21 mm Connection: 4x G ¼ inch (DIN ISO 228-1) Weight: Pressure tested: 2 bar Compatibility: Nvidia Geforce RTX 3080/3090 Scope of delivery: 1x HEATKILLER® V 1x mounting material Thermal Grizzly Kryonaut thermal paste
The EK-Quantum Vector FTW3 RTX 3080/3090 D-RGB GPU cooler, has been further developed based on the 2nd generation Vector series and designed for the EVGA FTW3 RTX 3080 and 3090 graphics cards. The Vector water block directly cools the GPU, VRAM and VRM (voltage regulation module), as the cooling fluid is routed directly over these critical areas. The base of the block is made of nickel-plated copper, while the top is made of acetal. Furthermore, the cooler has D-RGB lighting, with a total of 9 individually addressable LEDs, which makes the end piece shine pleasantly. The lighting is compatible with all common RGB sync technologies of the major motherboard manufacturers, such as ASRock Polychrome Sync, ASUS Aura Sync, Gigabyte RGB Fusion and MSI Mystic Light. Since the GPU cooler does not have a backplate, it is recommended to order a matching backplate. Such a backplate not only improves stability, but also promotes cooling performance, as it also serves as a passive cooler. Technical Data: Dimensions: 314 x 155 x 20.5mm (L x H x W) Material: Nickel-Plated Copper, Acetal Threads: G1/4" Scope of Delivery: EK-Quantum Vector FTW3 RTX 3080/3090 D-RGB series high-performance water block Mounting mechanism with screw-in brass standoffs Necessary mounting screws, nuts, and washers 2x Nickel plated brass plug G1/4” EK-Loop Multi Allen Key (6mm, 8mm, 9mm) Thermal pads Thermal grease EK-TIM Ectotherm (1g) Compatibility EVGA GeForce RTX 3080 FTW3 Gaming (10G-P5-3895-KR) EVGA GeForce RTX 3080 FTW3 Ultra Gaming (10G-P5-3897-KR) EVGA GeForce RTX 3080 FTW3 Ultra Hybrid Gaming (10G-P5-3898-KR) EVGA GeForce RTX 3080 FTW3 Ultra Hydro Copper Gaming (10G-P5-3899-KR) EVGA GeForce RTX 3090 FTW3 Gaming (24G-P5-3985-KR) EVGA GeForce RTX 3090 FTW3 Ultra Gaming (24G-P5-3987-KR) EVGA GeForce RTX 3090 FTW3 Ultra Hybrid Gaming (24G-P5-3988-KR) EVGA GeForce RTX 3090 FTW3 Ultra Hydro Copper Gaming (24G-P5-3989-KR)
PERFEKTE LÜFTER-REGULIERUNG DURCH PWM Die PWM-Funktion signalisiert über das Motherboard genauestens mit welcher Geschwindigkeit der Lüfter laufen muss. Damit wird eine maximale Kühlleistung bei minimalem Geräuschpegel garantiert. PWM SHARING TECHNOLOGY (PST) SENKT DEN GERÄUSCHPEGEL Durch die PST Funktion wird sichergestellt, dass alle Gehäuselüfter auf ein Signal arbeiten. Somit können alle Gehäuselüfter einheitlich eingestellt werden. INNOVATIVES DESIGN FÜR LEISE UND EFFIZIENTE BELÜFTUNG Durch das innovative Design der Lüfterblätter wird der Luftfluss verbessert und somit ist die Belüftung positiv beeinflusst. Das Lüfterrad wurde mit dem Fokus auf einen minimalen Geräuschpegel entworfen und bietet einen verbesserten Luftfluss und Druck. LANGE BETRIEBSDAUER Das Gleitlager ist mit einer hydrodynamischen Öl-Kapsel ausgestattet, somit wird vermieden, dass das Schmiermittel nicht verloren geht. Aus diesem Grund ist dieses Lager so leise wie ein Gleitlager hat aber eine wesentlich höhere und längere Betriebsdauer.
Thermaltake's Pure A14 is a PWM controlled LED fan available in four different colours: blue, green, red and white. Especially radiators benefit from the very quiet operation and low heat generation thanks to the self-lubricating hydraulic bearing. The anti-vibration pads also ensure low noise levels. As the sealing cap prevents the lubricant from escaping, a long service life is also guaranteed. The nine LEDs of the fan impress with a uniform brightness and high colour intensity and give the PC system the final touch. Technical Data: LED colour: White Dimenson: 140 x 140 x 25 mm Interface: 4-Pin PWM Fan Stated Voltage: 9.0 V Fan Rated Voltage: 12 V Rated current: 0.27 A Power Input: 3.24 W Fan Speed: 500 - 1500 rpm Max. Air Pressure: 2.05 mm-H2O Max Air Flow: 93.15 CFM Noise: 32 dB-A Bearing Type: Hydraulic Bearing Life Expectation: 40,000 hrs, 25℃ Weight: 176 g
The MasterLiquid ML120L RGB V2 from Coolermaster is a further development of the MasterLiquid Lite series. The dual-chamber pump of the ML120L RGB V2 has been redesigned to provide even more power and cooling efficiency with quieter operation. The radiator has also been upgraded, with the cooling surface increased by 25%, resulting in better heat dissipation. The fans have been equipped with the latest SickleFlow design, which makes them even quieter than before and cools the radiator effectively. The lighting can be controlled with the included RGB LED controller or via compatible mainboards. Technical Data Exterior Color: White CPU Socket: Intel : 2066, 2011-v3, 2011, 1151, 1150, 1155, 1156, AMD : AM4, AM3+, AM3, AM2+, AM2, FM2+, FM2, FM1 Radiator Material: Aluminum Radiator Dimensions: 277 x 119,6 x 27,2 mm / 10,9 x 4,7 x 1,1 inch Pump Dimensions: 79,9 x 76 x 47,1 mm / 3,1 x 3 x 1,9 inch Pump MTTF: 70,000 Hours Pump Noise Level: < 15 dBA Pump Connector: 3-Pin Pump Rated Voltage: 12 VDC Pump Power Consumption: 2.36W (LED 2.21W) Fan Dimensions (L x W x H): 120 x 120 x 25 mm / 4,7 x 4,7 x 1 inch Fan Quantity: 2 PCS Fan LED Type: RGB Fan Speed: 650-1800 RPM ± 5% Fan Airflow: 62 CFM (Max) Fan Noise Level: 8 - 27 dBA Fan Pressure: 2.5 mmH₂O (Max) Fan Life Expectancy: 160,000 Hours Fan Power Connector: 4-Pin (PWM) Fan Rated Voltage: 12VDC Fan Rated Current: 0.15A (LED 0.2A) RAM Clearance: N/A Warranty: 2 years Series: MasterLiquid Lite Cooler Type: Liquid Cooler Radiator Size: 240
The new Pure Rock 2 Black from be quiet! provides quiet cooling for multimedia and graphics applications. Its high-performance heat pipes and the Pure Wings 2 120mm PWM fan offer an unbeatable price-performance ratio. Top features of the Pure Rock 2 Black: Strong cooling power of 150W TDP Four powerful 6mm heat pipes with HDT technology Asymmetrical design holds memory banks Friday Pure Wings 2 120mm PWM fan for quiet operation with a maximum of 26.8 dB (A) Airflow-optimized fan blades to reduce noise-causing air turbulence Brushed aluminum finish The easy-to-understand installation kit can be easily installed from above Three years manufacturer warranty Technical specifications: Working area (W): 150 Dimensions (L x W x H): 62 x 121 x 155mm Number of cooling fins: 55 Material of the cooling fins: aluminum Material of the cooler base: aluminum / copper Number of heat pipes, diameter 4 / 6mm Fan data: Dimensions: 120 x 120 x 25mm Speed at 100% PWM (rpm): 1,500 Nominal voltage: 12V Power consumption: 1.44W Connector: 4-pin PWM Cable length: 220mm Scope of delivery: 1x be quiet! Pure Rock 2 Black Thermal paste (already applied) Backplate mounting set
Tüüp: Torn jahuti Mõõtmed koos ventilaatoriga (WxHxD): 251x164x104mm Ventilaatoreid: 4x 120x120x25mm, 32.2dB(A) Kaal koos ventilaatoritega: 2 kg Ühendus: 4-Pin PWM Ühilduvus: 1150/1151/1155/1156/1200, 1356/1366, 2011-0/2011-1/2011-3/2066, AM4, TR4/sTRX4/sWRX8/SP3
Profi-CPU-Wasserkühler von EKWB, Kühlerboden aus vernickeltem Kupfer, Deckel aus schwarzem Acetal, speziell für AMD AM4-Sockel, hochwertige Verarbeitung und edles Design, modulare Konstruktion mit austauschbaren Komponenten, integrierte D-RGB-Beleuchtung
The EK-Classic CPU Water Block 115x/20xx D-RGB, is a high-quality CPU water block of the top class for current Intel processors. It is characterised by a classic, elegant design, which is perfectly suited to the needs of enthusiasts and demanding users! The cooler is rounded off by the addressable D-RGB LED lighting and the CNC-milled, high-quality acrylic glass top. This product is compatible with the common RGB synchronisation technologies of all major motherboard manufacturers. The arrow marking on the 3-pin LED connector must be aligned with the +5V marking on the D-RGB (A-RGB) header. You can easily remove the LED strip cover, which is fixed with two screws, to replace the LED strip with another type of LED strip of your choice. Technical specifications: D-RGB cable length: 30cm D-RGB connector standard 3-pin (+5V, Data, Empty, Ground) CPU socket compatibility: Intel LGA-1200 Intel LGA-1150/1151/1155/1156 Intel LGA-2011(-3) Intel LGA-2066 Enclosed: EK-Classic CPU Water Block 115x/20xx D-RGB CPU block
OPTIMISED FOR STATIC PRESSURE During the development of the new BioniX P120, special emphasis was placed on a focused airstream and thus a high static pressure. The fan guarantees extremely efficient cooling, even with increased air resistance. Therefore, the BioniX P120 is particularly suitable for use on heatsinks and radiators. STRONG COOLING PERFORMANCE Numerous improvements, such as an updated engine technology and a newly developed fan design, have noticeably increased the performance of P-fans. MORE EFFICIENT TECHNOLOGY The motor is powered by a Neodym-Iron-Boron-Magnet ring of the newest generation, which allows the new BioniX P120 to run much more efficiently than its predecessors. This saves energy and lowers the coil temperature without comprimising the performance. MAXIMUM QUIETNESS, MINIMUM VIBRATION Even at low speeds the operating sound of the new ARCTIC motor is barely noticeable. Due to a sinus-magnetizing the new motor only creates about 5 % of the vibration from commutation of a regular DC-motor without filter. Consequently, there is no need for rubber spacers due to the steady and smooth torque of the new motor. EXTENDED LIFE SPAN A 10 °C lower motor temperature roughly doubles the life span of a fan. The new ARCTIC motor has a four times longer service life through its low coil temperature. Consequently, we have extended the warranty to 10 years. 200 TO 2100 RPM REGULATED VIA PWM PST With a wide range of regulation and the PWM Sharing Technology (PST), the BioniX P120 fan speed can be controlled synchronously with all your other fans together. This keeps noise at a minimum while guaranteeing maximum cooling performance when needed. HIGH QUALITY BEARING Thanks to an alloy/lubricant combination developed in Germany, friction within the bearing is reduced and greater efficiency is achieved. As a result, there is less heat development as well as less bearing noise, which means you can enjoy a longer service life from your fan. Technical Data Performance Fan Speed: 200 - 2100 rpm Airflow: 67.56 CFM/ 114.9 m³/h Static Pressure: 2.75 mm H₂O Noise Level: 0.45 Sone Operating Ambient Temperature: 0 - 40 °C Fan Fan Frame: BioniX Control Type: PWM PST Connector: 4-Pin-Connector + 4-Pin-Socket Fan Bearing: Fluid Dynamic Bearing Electric Characteristics Typical Voltage: 12 V DC Starting Voltage: 4.3 V Current/ Voltage: 0.13 A / 12 V Cable Lenght: 400 mm Size & Weight Lenght: 120 mm Width: 120 mm Height: 27 mm Weight: 140 g
L x W x H: 394,5 x 124 x 30 mm Material: cooling fins & channels, prechamber copper outer housing steel Fins per Inch: 15 Threads: 5x G1/4“ Fan size :120 mm Fan slots: 3 one-sided / 6 double-sided Pressure tested: 1,5 Bar Max working temperature: 180 °C
Can the Eisbaer from Alphacool become even better? Absolutely! Would the Eisbaer look even more impressive with aRGB? Definitely yes!! The Eisbaer Aurora AIO still cools the CPU with the well-known and high-quality copper cooler of the Eisbaer, although the surface area has been enlarged, compared to its predecessor. Also, the pump works much more efficiently with 10% more power, with reduced noise level. The hoses and fittings have also been completely revised and are now much smoother and more inconspicuous. Since durable TPV hose and fittings from the Enterprise Solution series are now used, safety and durability is also one of the features. For more individuality, fittings and hose can be easily replaced thanks to the G1/4 fittings. The Eisbaer Aurora, as before, can be expanded via the quick release fasteners. Also refilling is still possible. The most striking feature of the Eisbaer Aurora is the addressable RGB LED lighting. Here the focus is on the Eisbaer pump and the stylish Aurora LUX Pro fans. By using a compatible mainboard or controller, colour and effects can be adjusted individually. Technical Data: Radiator Dimension: 313,5 x 144 x 30 mm (L x W x H) Material: Full Copper Threads: 2x G1/4" Tubes Dimensions: 12,7 / 7,6 mm Material: Thermoplastic vulcanisates, EPDM/PP Colour: Matt black Operating temperature: -50 to +155°C Hardness: 35 Shore-A to 50 Shore-D Length: 40 cm Pump Housing Dimension: 66 x 66 x 69 mm (L x W x H) Material Reservoir: Transparent Nylon Threads: 2x G1/4" Connection Digital RGB: 3-Pin JST + 3-Pin 5V Quantity Digital aRGB LED: 10 Pump Speed: 2600 rpm Voltage: 7 - 13,5V DC Power Consumption: 4W Max. Flow Rate: 75 L/h Max. Head: 0,95 m Fans Size: 140 x 140 x 25 mm Speed: 600 - 1500 rpm Static Pressure: 0,41 - 1,6 mm H2O Air Flow Rate: 27 - 71 m³/h Bearings: Hydraulic Fan Connector: 4-Pin PWM Connection Digital RGB: 3-Pin JST + 3-Pin 5V Compatiblity Intel 775 / 1056 / 1155 / 1150 / 1151 / 1200 / 1700 / 2011 / 2011-3 / 2066 AMD AM2 / AM2+ / AM3 / AM3+ / FM1 / FM2 / FM2+ / AM4 / TR4 / sTRX4
The Alphacool ES 1U ServerRack has been specifically optimised to accommodate water cooling sets that can dissipate up to 490W of waste heat in this enclosure. For this purpose, the enclosure not only offers a mounting frame for a maximum of one 7x40mm full copper radiator of the Alphacool NexXxoS series. The optionally available Alphacool ES 40 mm fans with PWM control ensure optimum cooling performance. Drives The 1U server rack offers mounting options for two 5.25" drives on the left and right side of the front. Each 5.25" bay offers the alternative of mounting two 3.5" drives. A holding frame for mounting up to four 2.5" drives is pre-mounted in the centre front. This holding frame can be mounted at five other positions in the enclosure. Mainboard For mounting an SSI-EBB mainboard, all the usual screw connection options in the classic ATX format are available. This includes all mounting holes for Mini-ITX to EE-ATX. A graphics card in PCIe or 0.8" low-profile format can also be installed via a riser cable. A corresponding panel for 0.8" cards is pre-mounted in the case. Water cooling for 490W waste heat With an appropriate water cooling system, up to 490W of waste heat can be dissipated in this case. Alphacool offers special water cooling sets for this purpose, which can be individually configured and are delivered to the customer pre-filled. The mounting frame for the radiator and fans can be moved within the enclosure to suit any set-up. Please note: The case comes without I/O panel. Alphacool offers a separate set of I/O panel and cable set under item number 1021066. Overview of all compatible sets for this enclosure can be found here! (Attention: This link redirects you to the manufacturer's website www.alphacool.com) Alphacool recommends the following compatible products for this case. Radiators 1015753 - NexXxoS UT60 Full Copper X-Flow 40mm Dual (2 x 40mm) 1015717 - NexXxoS UT60 Full Copper X-Flow 40mm Triple (3 x 40mm) 1015718 - NexXxoS UT60 Full Copper X-Flow 40mm Quad (4 x 40mm) 1015719 - NexXxoS UT60 Full Copper X-Flow 40mm Penta (5 x 40mm) 1015720 - NexXxoS UT60 Full Copper X-Flow 40mm Hexa (6 x 40mm) 1015721 - NexXxoS UT60 Full Copper X-Flow 40mm Hepta (7 x 40mm) Reservoir with integrated pump top 1016193 - Alphacool Eisstation 40 DC-LT (Empfohlene Pumpe: 49061 ) 1017717 - Alphacool ES Reservoir 1U – DDC (Empfohlene Pumpe: 1019539 ) CPU Cooler 1016218 - Alphacool XPX 1U (AMD AM4, Intel LGA 1150, 1151, 1200, 2033, 2033-1, 2066) 1015815 - Alphacool XPX Pro 1U (AMD TR4, sTRX4, SP3, sWRX8, Intel LGA 2011, 2011,3, 2066, 3647) Fans 1020163 - Alphacool ES 40mm 400-15.000rpm PWM (40x40x28mm) 1020160 - Alphacool ES 40mm 400-10.000rpm PWM (40x40x20mm) Techncal data: Form factor 1HE (2U) Length 730,75 mm (28,77 Inch) Width 478,50 mm (18,84 Inch) Height 44,45 mm (1,75 Inch) Weight 7,62 kg (16,80 lbs) Material Galvanised sheet steel Materialdicke 1,2 mm Colour Case Grey Colour Front Black Standard Optional 2 x 5,25“ Slots Per Slot 1 x 3,5“ 4 x 2.5“ HDD/SSD Download Manual PDF: Alphacool ES 1U - 19" Serverrack Download Datasheet PDF: Alphacool ES 1U - 19" Serverrack
Now finally also with us the Black ICE Nemesis radiators. The Black Ice® Nemesis® GTS radiators are the next generation of computer radiators from Hardware Labs. These radiators offer an improved cooling performance when using
Alphacools HardTube family does get an additional sibling. The new HardTubes made out of borosilicate glass certainly bring a new level of quality into every system. The previous method that has been most commonly used for water cooling systems is normal PVC hoses - now Alphacool introduces a new approach to water cooling. The Alphacool HardTube additionally brings more tidiness into the system which enables a further structured impression. Borosilicate glass ticks every box on the checking list for watercooling systems. Stability and a brilliant appearance are not the only qualities that should lead to chosing this glass as even most chemicals and temperature flactuations can not harm the borosilicate glass. The whole chemical industry is depending on this glass and we can certainly say that this is not without reason. All glass tubes are compatible with the Alphacool HardTube connectors. Alphacool currently offers two classical sizes. One tube with a 16mm outer diameter and another with 13mm outer diameter. Further different length with 90° angles are introduced as its not possible to personally deform these tubes. To cut the tubes for the preferred length Alphacool recommends using a diamand cutting disc for the Dremel®. (Additionally availaible in our product line: Diamant cutting disc - Art.No: 1012316 , Dremel® - Art.No: 32196 and 32229 ) The following options are available: HardTube borosilicate glass 13/10mm 90° 10/30cm and 20/40cm HardTube borosilicate glass 13/10mm 40cm and 60cm HardTube borosilicate glass 16/11mm 90° 10/30cm and 20/40cm HardTube borosilicate glass 16/11mm 40cm and 60cm Scope of delivery: 1x HardTube borosilicate glass 16/11mm 40cm WARNING: Do not under any circumstances use the usual glass tube cutter to shorten the borosilicate glass tube. Borosilicate glass is a solid glass which can not be cut properly with a normal glas tube cutter. Please refer to a Dremel® with the needed cutting disc. Note: Due to the made-to-fit pipes, the connections must be plugged straight with a little effort. Attention: This article is not compatible with Monsoon fittings. Der8auer: Extremely Expensive Hardtubes and DIY Glass-Cutter
Alphacools HardTube family does get an additional sibling. The new HardTubes made out of borosilicate glass certainly bring a new level of quality into every system. The previous method that has been most commonly used for water cooling systems is normal PVC hoses - now Alphacool introduces a new approach to water cooling. The Alphacool HardTube additionally brings more tidiness into the system which enables a further structured impression. Borosilicate glass ticks every box on the checking list for watercooling systems. Stability and a brilliant appearance are not the only qualities that should lead to chosing this glass as even most chemicals and temperature flactuations can not harm the borosilicate glass. The whole chemical industry is depending on this glass and we can certainly say that this is not without reason. All glass tubes are compatible with the Alphacool HardTube connectors. Alphacool currently offers two classical sizes. One tube with a 16mm outer diameter and another with 13mm outer diameter. Further different length with 90° angles are introduced as its not possible to personally deform these tubes. To cut the tubes for the preferred length Alphacool recommends using a diamand cutting disc for the Dremel®. (Additionally availaible in our product line: Diamant cutting disc - Art.No: 1012316 , Dremel® - Art.No: 32196 and 32229 ) The following options are available: HardTube borosilicate glass 13/10mm 90° 10/30cm and 20/40cm HardTube borosilicate glass 13/10mm 40cm and 60cm HardTube borosilicate glass 16/11mm 90° 10/30cm and 20/40cm HardTube borosilicate glass 16/11mm 40cm and 60cm Scope of delivery: 1x HardTube borosilicate glass 16/11mm 90° 10/30cm WARNING: Do not under any circumstances use the usual glass tube cutter to shorten the borosilicate glass tube. Borosilicate glass is a solid glass which can not be cut properly with a normal glas tube cutter. Please refer to a Dremel® with the needed cutting disc. Note: Due to the made-to-fit pipes, the connections must be plugged straight with a little effort. Attention: This article is not compatible with Monsoon fittings. Der8auer: Extremely Expensive Hardtubes and DIY Glass-Cutter
Now finally also with us the Black ICE Nemesis radiators. The Black Ice® Nemesis® GTS radiators are the next generation of computer radiators from Hardware Labs. These radiators offer an improved cooling performance when using
The Barrow LRC2.0 full coverage GPU Water Block for Colorful BATTLEAX 3090 Aurora is a complete GPU cooler. It covers and cools all important components such as GPU RAM, capacitors and GPU processor. This cooler was specially developed for the Nvidia Colorful BATTLEAX 3090. The cooler plate is made of nickel-plated copper and is equipped with special micro cooling channels for optimal cooling. The lid with the integrated RGB lighting is made of acrylic glass. The RGB's are controlled via a 4Pin connector on the mainboard. Compatibility Colorful BATTLEAX RTX 3090 24G Colorful BATTLEAX RTX 3080 10G Technical Data Material: Nickel-Plated Copper (base) / Acrylic (cover) Dimensions: 250 x 122,3 x 20,4mm Colour: Silver / Transparent Cover: complete GPU cooler Threads: 2x G1/4" female Lighting: integrated RGB lighting Connections: 4Pin 5V RGB lighting Scope of Delivery Barrow LRC2.0 full coverage GPU Water Block for Colorful BATTLEAX 3090 Aurora
The Barrow LRC2.0 full coverage GPU Water Block for Colorful Vulcan 3090 Aurora is a complete GPU cooler. It covers and cools all important components such as GPU RAM, capacitors and GPU processor. This cooler was specially developed for the Nvidia Colorful Vulcan 3090. The cooler plate is made of nickel-plated copper and is equipped with special micro cooling channels for optimal cooling. The lid with the integrated RGB lighting is made of acrylic glass. The RGB's are controlled via a 4Pin connector on the mainboard. Compatibility Colorful iGame RTX 3080 Vulcan X OC 10G Colorful iGame RTX 3080 Vulcan OC 10G Colorful iGame RTX 3080 Vulcan 10G Colorful iGame RTX 3080 Neptune OC 10G Colorful iGame RTX 3080 Neptune 10G Technical Data Material: Nickel-Plated Copper (base), Acrylic Glass (cover) Dimensions: 296,2 x 145,5 x 20,4mm Colour: Silver / Transparent Cover: complete GPU cooler Lighting: integrated RGB lighting Threads: 2x G1/4" internal thread Connections: 4Pin 5V RGB lighting Scope of Delivery Barrow LRC2.0 full coverage GPU Water Block for Colorful Vulcan 3090 Aurora
The Barrow LRC2.0 full coverage GPU Water Block for Colorful 3090 Advanced OC Aurora is a complete GPU cooler. It covers and cools all important components such as GPU RAM, capacitors and GPU processor. This cooler was specially developed for the Nvidia Colorful 3090 Advanced. The cooler plate is made of nickel-plated copper and is equipped with special micro cooling channels for optimal cooling. The lid with the integrated RGB lighting is made of acrylic glass. The RGB's are controlled via a 4pin connector on the mainboard. Compatibility Colorful iGame RTX 3090 Advanced OC Colorful iGame RTX 3090 Advanced Colorful iGame RTX 3080 Advanced OC 10G Colorful iGame RTX 3080 Advanced 10G Colorful iGame RTX 3080 Ultra OC 10G Colorful iGame RTX 3080 Ultra 10G Technical Data Material: Nickel-Plated Copper (base), Acrylic Glass (cover) Dimensions: 278,7 x 122,3 x 23,9mm Colour: Silver / Transparent Cover: complete GPU cooler Lighting: integrated RGB lighting Threads: 2x G1/4" female Connections: 4Pin 5V RGB lighting Scope of Delivery Barrow LRC2.0 full coverage GPU Water Block for Colorful 3090 Advanced OC Aurora.
Now finally also with us the Black ICE Nemesis radiators. The Black Ice® Nemesis® GTX radiators are the next generation of computer radiators from Hardware Labs. These radiators offer an improved cooling performance when using
The Bykski silver fittings are made of brass and are designed for 16/10mm Soft Tubes. Technical Data: Material: Brass Color: Silver Thread: G1/4 Zoll Thread Length: 5 mm Tubing Size: 16/10 mm (ID 3/8", OD 5/8")
The fitting in black by Bykski, is made of brass and has a 90° angle. The fitting fits 14mm Hard Tubes and allows 90 degree bends in the water cooling system without having to deform the tube itself. Technical Data: Material: Brass Colour: Black Angle: 90° Connection: 2x Ø 14 mm Compatible Tube: 14 mm OD (PETG, Acrylic, Metal)
Now finally also with us the Black ICE Nemesis radiators. The Black Ice® Nemesis® GTS radiators are the next generation of computer radiators from Hardware Labs. These radiators offer an improved cooling performance when using
With the 5v Addressable RGB (RBW) adapter cable from Bykski, a 5V A-RGB LED header can be connected directly to a compatible mainboard. Technical Data Voltage: 5V only LED Type: 5V RBW Scope of Delivery 1x Adapter Cable
Now finally also with us the Black ICE Nemesis radiators Black Ice® Nemesis® GTX Micro Radiators feature the innovative GTX® dual-core design and offer even higher performance with less airflow or noise. With the standard G1/4" threads, you can use all common connections of your water cooling system. Technical details: 92mm x 1 Fan Radiator 121 x 93 x 54 mm (L x B x H) 16 FPI 25 micron copper fins Now optimized for ultra-stealth fans with 800 rpm. Supercruise optimizations for scalable performance with higher speed fans Increased flow rate Standard G 1/4″ Input/output connections Standard M4 mounting thread
Now finally also with us the Black ICE Nemesis radiators Black Ice® Nemesis® GTX Micro Radiators feature the innovative GTX® dual-core design and offer even higher performance with less airflow or noise. With the standard G1/4" threads, you can use all common connections of your water cooling system. Technical details: 92mm x 2 Fan Radiator 213 x 84 x 54 mm (L x B x H) 16 FPI 25 micron copper fins Now optimized for ultra-stealth fans with 800 rpm. Supercruise optimizations for scalable performance with higher speed fans Increased flow rate Standard G 1/4″ Input/output connections Standard M4 mounting thread
Now finally also with us the Black ICE Nemesis radiators The Black Ice® Nemesis® SR2™ Xtreme+ radiators, have three rows of copper fins optimised for maximum air pressure. This, together with the high internal flow rate, achieves a cooling performance that is second to none. With the standard G1/4" threads, you can use all common connections of your water cooling system. Technical details: 480mm Radiator 518 x 133 x 60mm (L x W x H) Built-in 8-PORT Inlet/Outlet manifold system 9 FPI 45 micron copper fins Now optimized for ultra-stealth fans with 800 rpm. Supercruise optimizations for scalable performance with higher speed fans Increased flow rate Standard G 1/4″ Input/output connections Standard M4 mounting thread
The 90 ° angle adapter from Bykski is made of brass and has two G1 / 4 “internal threads. Technical specifications: Dimensions: 23.7 x 23.7 x 18.68 mm Material: brass Colour: gold Angle: 90 ° Thread: 2x G1 / 4 “internal thread
