Optimised for Static Pressure During the development of the new P14 PWM, special emphasis was placed on a focused airstream and thus a high static pressure. The fan guarantees extremely efficient cooling, even with increased air resistance. Therefore, the P14 PWM is particularly suitable for use on heatsinks and radiators. More Efficient Technology The motor is powered by a Neodym-Iron-Boron-Magnet ring of the newest generation, which allows the new P14 PWM to run much more efficiently than its predecessors. This saves energy and lowers the coil temperature without comprimising the performance. Maximum Quietness, Minimum Vibration Even at low speeds the operating sound of the new ARCTIC motor is barely noticeable. Due to a sinus-magnetizing the new motor only creates about 5 % of the vibration from commutation of a regular DC-motor without filter. Consequently, there is no need for rubber spacers due to the steady and smooth torque of the new motor. Extended Life Span A 10 °C lower motor temperature roughly doubles the life span of a fan. The new ARCTIC motor has a four times longer service life through its low coil temperature. Consequently, we have extended the warranty to 10 years. 200 to 1700 RPM regulated via PWM Thanks to the 4-pin connector, the RPM can be regulated in a broad spectrum via PWM. In this way, noise is kept at a minimum while maximum cooling performance is guaranteed when needed. High Quality Bearing Thanks to an alloy/lubricant combination developed in Germany, friction within the bearing is reduced and greater efficiency is achieved. As a result, there is less heat development as well as less bearing noise, which means you can enjoy a longer service life from your fan. Technical Data: Performance Fan Speed: 200 - 1700 rpm Airflow: 72.8 CFM/ 123.76 m³/h Static Pressure: 2,40 (mm/H2O) Noise Level: 0.3 Sone Fan Fan Frame: Standard Controll Typ: PWM Connector: 4-Pin Connector Fan Bearing: Fluid Dynamic Bearing Electric Characteristics Typical Voltage: 12 V DC Starting Voltage: 3.9 V Current: 0.12 A Cable Lenght: 400 mm Size & Weight Lenght: 140 mm Width: 140 mm Height: 27 mm Weight: 194 g
Thermaltake's Riing Quad 12 RGB is a PWM controlled fan with a quadruple 16.8 million colour LED ring. Due to the self-lubricating hydraulic bearing, the fan benefits from very quiet operation and low heat generation. As the sealing cap prevents lubricant leakage, a long service life is also guaranteed. The design of the fan is based on performance, which is why it features high static pressure and efficient cooling. The anti-vibration pads also ensure low noise levels. The four independent LED rings, with over 54 addressable LEDs in total, provide impressive light coverage and high colour intensity. The extensive and breathtaking effects add the finishing touches to your housing and give it a unique look. As other controllers (also from Thermaltake) are not compatible with the fans, the 3-piece set includes a separate controller. It is recommended to connect only 5 Riing Trio fans per controller (connected with a Molex cable). If you own a lot of Thermaltake RGB PLUS products, you can really let off steam with the TT RGB PLUS software. Whether you want to synchronise the lighting in games, movies and music or specific lighting modes, colours and speeds, the software will make your system really shine. In addition, the software can also regulate fan speeds, for example, and also offers the option of voice control. With Thermaltake's NeonMaker software, the possibilities are even extended to create incredible and dynamic light shows. Furthermore, all Thermaltake TT RGB PLUS products are compatible with Razer chroma lighting and Amazon Alexa. Technical Data: Dimenson: 120 x 120 x 25 mm Interface: USB 2.0 connectors (9 Pin) Fan Stated Voltage: 9.0 V Fan Rated Voltage: 12 V and 5 V Rated current: 12V - 0.09 A , 5V - 0.9 A Power Input: 12V - 3.24 W, 5V - 13.5 W Fan Speed: 500 - 1500 rpm Max. Air Pressure: 1.4 mm-H2O Max Air Flow: 40.9 CFM Noise: 25 dB-A Bearing Type: Hydraulic Bearing Life Expectation: 40,000 hrs, 25℃ Weight: 189 g
The EK-Quantum Scalar Flow Indicator is a high-quality GPU-mounted flow indicator with addressable D-RGB illumination. It visually represents the coolant flow rate, which is often difficult to see with the naked eye. This can be very useful to immediately see if your loop is in perfect condition or if there are problems with the pump or flow. It has dedicated G1/4" inputs and outputs. It is essential to ensure that the labelled connections are connected correctly. This product is compatible with the common RGB synchronisation technologies of all major motherboard manufacturers. The anodised aluminium cover hides the LED hotspots and provides uniform illumination. Enclosed: EK-Quantum Scalar Flow Indicator Bottom-Top D-RGB - Nickel G1/4" nickel-plated brass plug x 1
The EK-Quantum Scalar Flow Indicator is a high-quality GPU-mounted flow indicator with addressable D-RGB illumination. It visually represents the coolant flow rate, which is often difficult to see with the naked eye. This can be very useful to immediately see if your loop is in perfect condition or if there are problems with the pump or flow. It has dedicated G1/4" inputs and outputs. It is essential to ensure that the labelled connections are connected correctly. This product is compatible with the common RGB synchronisation technologies of all major motherboard manufacturers. The anodised aluminium cover hides the LED hotspots and provides uniform illumination. Enclosed: EK-Quantum Scalar Flow Indicator Bottom-Top D-RGB - Black G1/4" nickel-plated brass plug x 1
Visual appearance combined with functionality. After the successful launch of the “Lian Li 011D Mini MK1“, now the Lian Li Mini is followed by the “MK2” front distro plate. It is made of high-quality and transparent acrylic glass. Despite the small case, our distro plate MK2 allows all radiators as well as GPU and CPU to be connected in the circuit. This is rendered possible by a large chamber and 5 channels with a total of 12 ports (incl. fill port & drain port). The “MK2” will replace the original tempered glass pane. The distro plate is made of high-quality acrylic and the accuracy of fit is assured. Additionally, we use EPDM seals to guarantee leak tightness. After the leak test, a test seal is glued on the back of the plate. The screw-fitting points provided by Lian Li are used for fixation. To mount the distro plate safely, 4 screws with sealing disc are included in the scope of delivery. It is important to ensure that only (!) “ECWB SE360 (2x) “ & “ ECA SE240 (1x)“ radiators are usable because the accuracy of fit can only be assured in this case. A frame sticker (you may choose between black or white) decorates the sides of the front. Thereby, mounting strips that are glued on the rear side of the distro are covered. Overview of Features smallest distro plate of the Lian Li series frame sticker, selectable in black or white clever plug-in system for effortless installation adapter allows perfect fit of a D5 pump compatible with EK-CoolStream SE360 2x and 1x SE240mm (radiators) Technical details Material: high-quality acrylic glass, plastic Manufacturing: CNC machining of the acrylic, assembly by hand Dimensions: without pump (W x H x D): 487 x 211 x 21 mm, with pump (W x H x D): 487 x 211 x 90 mm Colour: transparent Connections: 12x G1/4" Capacity: 435 ml Compatibility: 3x360mm fan space Scope of Delivery Lian Li Mini MK2 4x M3 screws
120 mm großer PWM-Lüfter, digital adressierbare RGB-LED-Beleuchtung (3-Pin), Drehzahl von max. 1.500 U/min, transparenter Rahmen und Lüfterblätter, inklusive Schrauben
Zwei 120-mm-Lüfter im Set, 800 bis 1.800 U/min, max. 127,4 m³/h Fördervolumen, max. 2,3 mmH2O statischer Druck, digital adressierbarer RGB-Beleuchtung, inkl. RGB- und Lüftersteuerung
EK Quantum Flow Indicator D-RGB is a high-quality flow indicator with addressable RGB lighting, which belongs to the Quantum Line. It visually represents the coolant flow rate, which is often difficult to see with the naked eye. This can be very useful to immediately see if your loop is in perfect condition or if there are problems with the pump or flow. In addition, this is a very elegant cast acrylic part, with an anodised aluminium cover, which has the same surface as the EK-Quantum Vector GPU backplates. It has three G1/4" connectors, all of which are female. It can be mounted in the middle of a tube with two fittings or attached to a radiator or pump at each G1/4" connection. Each of the threads, can be used either as an inlet or outlet. This product is compatible with the common RGB synchronisation technologies of all major motherboard manufacturers. The anodised aluminium cover hides the LED hotspots and provides uniform illumination. Enclosed: EK-Quantum Flow Indicator D-RGB – Nickel 1x G1/4" nickel-plated brass plug
Vernickeltes Compression Fitting von EK Water Blocks, für Röhren mit 12 mm OD, Kompatibel zu Röhren aus Acryl / PETG / Kupfer / Messing / Edelstahl, 6er Pack
Schwarz beschichtetes Compression Fitting von EK Water Blocks, für Röhren mit 12 mm OD, Kompatibel zu Röhren aus Acryl / PETG / Kupfer / Messing / Edelstahl, 6er Pack
This is the 2nd generation Vector GPU water block from the EK® Quantum Line, designed for EVGA® FTW3 RTX 3070 graphics cards based on the latest NVIDIA® Ampere™ architecture. For a precise compatibility match of this water block, we recommend you refer to the EK Cooling Configurator. An EK Water Block for FTW3 RTX 3070 EK-Quantum Vector FTW3 3070 D-RGB water block is compatible with FTW3 RTX 3070 graphics cards. The Vector water block actively cools the GPU, VRAM, power stages, and chokes in the VRM (voltage regulation module). These newly developed water blocks feature optimized flow paths that reduce hydrodynamic instabilities and vortexing (dead spots) inside of them. The EK-Quantum Vector Series water blocks use an Open Split-Flow cooling engine design, which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, meaning it can be used with weaker water pumps or pumps running on low-speed settings, and still achieve top performance. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performance when used in any given coolant flow orientation. The fin array is populated by 28 microfins with 0.6mm wide microchannels that provide optimal cooling performance, without unnecessary flow restrictions or clogging hazards. The base of the block is CNC-machined out of nickel-plated electrolytic copper, while its top is CNC-machined out of durable POM acetal. These 2nd generation Vector GPU water blocks also feature Acetal terminals. The watertight sealing is ensured by high-quality EPDM O-rings, while brass standoffs are already pre-installed and allow for a safe and easy installation procedure. D-RGB lighting on EK-Quantum Vector FTW3 RTX 3070 D-RGB water block The aesthetic corner end-piece is housing the addressable D-RGB LEDs. This water block boasts a total of 8 individually addressable RGB LEDs, and it is compatible with popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 3-pin D-RGB LED connector is to be aligned with the +5V marking on the D-RGB (addressable) header. Backplate for the EK-Quantum Vector FTW3 3070 water block EK recommends the purchase of a retention backplate, especially for the 3070 models of graphics cards. The backplate improves the overall aesthetics of your graphics cards and also provides additional passive cooling for the GPU core, and backside of the printed circuit board VRM section. Technical Specification Dimensions: (LxHxW) - 314x155x21mm Enclosed EK-Quantum Vector FTW3 RTX 3070 D-RGB series high-performance water block Mounting mechanism with screw-in brass standoffs Necessary mounting screws, nuts, and washers 2x Nickel plated brass plug G1/4” EK-Loop Multi Allen Key (6mm, 8mm, 9mm) Thermal pads Thermal grease EK-TIM Ectotherm (1g)
This is the 2nd generation Vector GPU water block from the EK® Quantum Line, designed for EVGA® FTW3 RTX 3070 graphics cards based on the latest NVIDIA® Ampere™ architecture. An EK Water Block for FTW3 RTX 3070 EK-Quantum Vector FTW3 3070 D-RGB water block is compatible with FTW3 RTX 3070 graphics cards. The Vector water block actively cools the GPU, VRAM, power stages, and chokes in the VRM (voltage regulation module). These newly developed water blocks feature optimized flow paths that reduce hydrodynamic instabilities and vortexing (dead spots) inside of them. The EK-Quantum Vector Series water blocks use an Open Split-Flow cooling engine design, which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, meaning it can be used with weaker water pumps or pumps running on low-speed settings, and still achieve top performance. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performance when used in any given coolant flow orientation. The fin array is populated by 28 microfins with 0.6mm wide microchannels that provide optimal cooling performance, without unnecessary flow restrictions or clogging hazards. The base of the block is CNC-machined out of nickel-plated electrolytic copper, while its top is CNC-machined out of glass-like cast Acrylic. These 2nd generation Vector GPU water blocks also feature Acetal terminals. The watertight sealing is ensured by high-quality EPDM O-rings, while brass standoffs are already pre-installed and allow for a safe and easy installation procedure. D-RGB lighting on EK-Quantum Vector FTW3 RTX 3070 D-RGB water block The aesthetic corner end-piece is housing the addressable D-RGB LEDs. This water block boasts a total of 8 individually addressable RGB LEDs, and it is compatible with popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 3-pin D-RGB LED connector is to be aligned with the +5V marking on the D-RGB (addressable) header. Backplate for the EK-Quantum Vector FTW3 3070 water block EK recommends the purchase of a retention backplate, especially for the 3070 models of graphics cards. The backplate improves the overall aesthetics of your graphics cards and also provides additional passive cooling for the GPU core, and backside of the printed circuit board VRM section. Technical Specification Dimensions: (LxHxW) - 314x155x21mm Enclosed EK-Quantum Vector FTW3 RTX 3070 D-RGB series high-performance water block Mounting mechanism with screw-in brass standoffs Necessary mounting screws, nuts, and washers 2x Nickel plated brass plug G1/4” EK-Loop Multi Allen Key (6mm, 8mm, 9mm) Thermal pads Thermal grease EK-TIM Ectotherm (1g)
EK-Quantum Vector N+ RX 6800XT/6900XT is a 2nd generation Vector GPU water block from the EK® Quantum Line. It is made for SAPPHIRE NITRO+ 6800XT and 6900XT graphics cards based on the latest AMD® RDNA2™ architecture. EK-Quantum Vector N+ RX 6800XT/6900XT water block for SAPPHIRE NITRO+ GAMING RX 6800 XT and 6900 XT GPUs EK-Quantum Vector N+ RX 6800XT/6900XT water block is compatible with SAPPHIRE NITRO Radeon RX 6800XT, and 6900XT graphics cards. The Vector water block directly cools the GPU, VRAM, and the VRM (voltage regulation module) as a cooling liquid is channeled right over these critical areas. The water block is in contact with power stages as well as Inductor chokes to maximize cooling and minimize the chances of coil whine. These newly developed water blocks feature optimized flow paths that reduce hydrodynamic instabilities and vortexing (dead spots) inside of them. The EK-Quantum Vector Series water blocks use an Open Split-Flow cooling engine design, which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, meaning it can be used with weaker water pumps or pumps running on low-speed settings, and still achieve top performance. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performance when used in any given coolant flow orientation. The base of the block is CNC-machined out of high-grade nickel-plated electrolytic copper, while its top is CNC-machined out of durable black POM Acetal. These 2nd generation Vector GPU water blocks also feature acetal terminals. The watertight sealing is ensured by high-quality EPDM O-rings, while brass standoffs are already pre-installed and allow for a safe and easy installation procedure. D-RGB lighting on EK-Quantum N+ Vector RX 6800XT/6900XT D-RGB water block The aesthetic end-piece is housing the addressable D-RGB LED strip. These water blocks boast a total of 9 individually addressable RGB LEDs, and a LED-lit terminal. They are compatible with popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 3-pin D-RGB LED connector is to be aligned with the +5V marking on the D-RGB (addressable) header. Backplate for the N+ 6800XT/6900XT water block EK recommends the purchase of a retention backplate, which improves the overall aesthetics of your graphics cards, and also provides additional passive cooling for the GPU core and backside of the printed circuit board VRM and VRAM sections. Technical Specification Dimensions: (LxHxW) - 285x149x16.5mm Enclosed EK-Quantum Vector N+ RX 6800XT/6900XT series high-performance water block Mounting mechanism with screw-in brass standoffs Necessary mounting screws, nuts, and washers 2x Nickel plated brass plug G1/4” EK-Loop Multi Allen Key (6mm, 8mm, 9mm) Thermal pads Thermal grease EK-TIM Ectotherm (1g)
Backplate für GPU-Wasserkühlung, für EK-Quantum Vector TUF 6800/6900, aus anodisiertem Aluminium, bietet erhöhte Stabilität, mit Wärmeleitpad für passive Kühlung der PCB-Komponenten
Tootekood: PH-GB6900ASSRX_CR01GTIN: 886523701668Jahutid ja lisad
Full-Block-GPU-Kühler für Custom-Wasserkühlungen, für ASUS ROG Strix/TUF AMD RX 6800/6900, Deckel aus transparentem Acrylglas, mit verchromtem Aluminium-Cover, integrierte digitale RGB-Beleuchtung (3-Pin, 5VDG)
Tootekood: PH-GB6900ASSRX_BK01GTIN: 886523701651Jahutid ja lisad
Full-Block-GPU-Kühler für Custom-Wasserkühlungen, für ASUS ROG Strix/TUF AMD RX 6800/6900, Deckel aus transparentem Acrylglas, mit schwarzem Aluminium-Cover, integrierte digitale RGB-Beleuchtung (3-Pin, 5VDG)
Die CPU-Wasserblöcke der EK-Quantum Velocity² Serie beinhalten die nächste Generation der OptiFlow Kühlung. Sie verwenden eine spezielle Kombination aus Montagedruck und Coldplate-Geometrie, die auf das IHS- und Die-Layout von Intel LGA 1700 Sockel-Prozessoren zugeschnitten ist. Dank der geringen hydraulischen Durchflussbeschränkung können diese Produkte in Setups mit schwächeren Wasserpumpen oder niedrigeren Pumpendrehzahlen für einen noch leiseren Betrieb eingesetzt werden, wobei sie dennoch Spitzenleistungen erzielen! Technische Daten: D-RGB Kabellänge: 50cm D-RGB-Anschluss 3-poliger 5V-Digital-LED-Header (Pinout: +5V | Digital | Blockiert | Masse) CPU-Sockel-Kompatibilität: Intel LGA 1700 Lieferumfang: EK-Quantum Velocity² CPU-Wasserblock Exact Mount Universal-CPU-Montagemechanismus EK-Velocity² Rückwand 2.5mm Inbus(HEX)-Schlüssel Jetplate für LGA 1700 Wärmeleitpaste Thermal Grizzly Hydronaut (1g)
Die R100B Reservoir’s der neuen ANTILA PURE-Serie von RAIJINTEK bieten einzigartige Regenbogen Effekte des A-RGB’s (5 V adressierbar) durch die eingebaute LED-Lichtkappe. Die Lösung befindet sich auf höchstem Niveau für PC-Enthusiasten und kundenspezifische PC-Modder, um ein Super-ARGB-LED-Effekt Wasser-kühlsystem zu erstellen. Die ANTILA PURE-Serie wird aus hochwertigem POM- und Echtglas hergestellt, um eine kristallklare, stabile, leise, leistungsstarke und langlebige Lösung zu bieten. Mit der ANTILA PURE-Serie können PC-Enthusiasten nicht nur ein bemerkenswert, wunderschönes Flüssigkeitskühlsystem bauen, sondern auch extern modulare Upgrades für ihr Gehäuse kombinieren. Eine robuste Montagehalterung bietet dem Benutzer auch eine zuverlässige, richtungsweisende Montagemöglichkeit und eine benutzerfreundliche Installation. Die ANTILA PURE-Serie ist das beste LED-Reservoir für Ihre Wasserkühlung Ihres Systems! Technische Daten: Anzahl: 1 Stück Dimensionen [l×b×h]: 77×77×173 mm Reservoir Dimensionen: 65×65×127 mm Kühlmittel Kapazität: 400 ml Material: POM + Glas + Aluminium + Stahl Material Gewicht: 780 g Schraubgewinde: G 1/4" Addressable LED: 12 LED Rainbow (4pin header, 2510 spec) – Addressable LED LED Control Method: Motherboard RGB HEADER/ Fernbedienung und RJK Control Box LED Input Connector: 4-PIN header (2.5 Crimp) LED Eingangsspannung: 5V
The vertical bracket from Singularity can be used to mount a Protium series reservoir or pump attachment vertically on a 120 or 140 fan slot of a radiator. It is even possible to mount two reservoirs or pump attachments. Technical Data Colour: Silver Material: Aluminium (mounting plates), Stainless Steel (screws) Scope of Delivery: 2x SC Universal 120/140 Back Plate Mounting Plate 2x Vertical mounting plate 4x M4 Button Head Hex (10 mm) 4x M4 Countersunk Hex (10 mm) 4x M4 Washers 4x M4 Nut
The vertical bracket from Singularity can be used to mount a Protium series reservoir or pump attachment vertically on a 120 or 140 fan slot of a radiator. It is even possible to mount two reservoirs or pump attachments. Technical Data Colour: Black Material: Aluminium (mounting plates), Stainless Steel (screws) Scope of Delivery: 2x SC Universal 120/140 Back Plate Mounting Plate 2x Vertical mounting plate 4x M4 Button Head Hex (10 mm) 4x M4 Countersunk Hex (10 mm) 4x M4 Washers 4x M4 Nut
The Protium expansion tank from Singularity Computers is a 200mm tube with a diameter of 60mm. Together with the acrylic attachments, the expansion tank reaches a height of 239mm. It has a total of seven G1/4" ports and the tube itself is made of acrylic. Technical Data: Dimensions: 60 x 60 x 239 mm (L x W x H) Diameter: 60 mm Material: Acrylic (lid, base, reservoir), Aluminium (retention rings) Color: Silver, Transparent Threads: 7x G1/4" Scope of Delivery: 1x 200 mm acrylic reservoir 2x Aluminium retention rings 1x 90° quad port cap (bottom) 1x Triple port cap (cover) 1x 16 mm internal acrylic flow standpipe 5x G1/4" stop fittings 2x Silicone O-rings
Schicker zylindrischer Ausgleichsbehälter, Röhre und Aufsätze aus transparentem Acryl, drei Aufsätze für flexible Anschlussmöglichkeiten, schwarze Sicherungsringe aus Aluminium
Schicker zylindrischer Ausgleichsbehälter, Röhre aus transparentem Acryl, Aufsätze mit mattem Finish, drei Aufsätze für flexible Anschlussmöglichkeiten, schwarze Sicherungsringe aus Aluminium
