The perfect solution for perfect curves in the Alphacool HardTubes is now available. Simply slide the silicon insert into the plexiglass tube and heat up the desired section. Thanks to the extreme heat resistance of silicon, the tube can be bent without the curved section buckling. After it cools, the silicon insert can simply be pulled out. Available for tubes with 10mm, 12mm, and now 13mm inner diameters, and each size comes in 30cm length for curves in shorter tubes or 100cm length for curves in longer tubes. Technical Details Length: 100cm Thickness: 13mm Colour: blue Scope of Delivery 1x Alphacool silicon bending insert 100cm for ID 1/2” / 13mm HardTubes - blue NoticeDue to the manufacturing process, the diameter can vary by 0.5 - 1mm.
Optimised for Static Pressure During the development of the new P14 PWM, special emphasis was placed on a focused airstream and thus a high static pressure. The fan guarantees extremely efficient cooling, even with increased air resistance. Therefore, the P14 PWM is particularly suitable for use on heatsinks and radiators. More Efficient Technology The motor is powered by a Neodym-Iron-Boron-Magnet ring of the newest generation, which allows the new P14 PWM to run much more efficiently than its predecessors. This saves energy and lowers the coil temperature without comprimising the performance. Maximum Quietness, Minimum Vibration Even at low speeds the operating sound of the new ARCTIC motor is barely noticeable. Due to a sinus-magnetizing the new motor only creates about 5 % of the vibration from commutation of a regular DC-motor without filter. Consequently, there is no need for rubber spacers due to the steady and smooth torque of the new motor. Extended Life Span A 10 °C lower motor temperature roughly doubles the life span of a fan. The new ARCTIC motor has a four times longer service life through its low coil temperature. Consequently, we have extended the warranty to 10 years. 200 to 1700 RPM regulated via PWM Thanks to the 4-pin connector, the RPM can be regulated in a broad spectrum via PWM. In this way, noise is kept at a minimum while maximum cooling performance is guaranteed when needed. High Quality Bearing Thanks to an alloy/lubricant combination developed in Germany, friction within the bearing is reduced and greater efficiency is achieved. As a result, there is less heat development as well as less bearing noise, which means you can enjoy a longer service life from your fan. Technical Data: Performance Fan Speed: 200 - 1700 rpm Airflow: 72.8 CFM/ 123.76 m³/h Static Pressure: 2,40 (mm/H2O) Noise Level: 0.3 Sone Fan Fan Frame: Standard Controll Typ: PWM Connector: 4-Pin Connector Fan Bearing: Fluid Dynamic Bearing Electric Characteristics Typical Voltage: 12 V DC Starting Voltage: 3.9 V Current: 0.12 A Cable Lenght: 400 mm Size & Weight Lenght: 140 mm Width: 140 mm Height: 27 mm Weight: 194 g
The ICEBERG THERMAL DRIFTIce Thermal Pad by Iceberg Thermal is designed to efficiently dissipate heat and enhance the performance of your electronic devices. Measuring 40mm by 80mm with a thickness of 1.0mm, this thermal pad is perfect for a variety of applications. It is lightweight, with a gross weight of only 0.020 kg, making it easy to handle and install. Ensure your devices remain cool and functional with this high-quality thermal pad.
The ICEBERG THERMAL DRIFTIce Thermal Pad by Iceberg Thermal is an effective solution for heat management in electronic devices. Measuring 40mm by 120mm with a thickness of 1.5mm, this thermal pad provides optimal thermal conductivity to improve device performance. It is lightweight, with a gross weight of only 0.035 kg, making it easy to handle and install. Ideal for a variety of applications, this thermal pad ensures efficient heat dissipation, protecting components from overheating.
EK-Loop Connect Level Sensor TBE 60 is a coolant level sensor provides a warning when the reservoir reaches a point where it would be prudent to top it off. Due to the coolant evaporation through the tubing, it makes sure the pump never runs dry. Also, in case of a leak, it warns you of the coolant level being below its optimal value. It attaches to the tube of the EK tubular-style reservoirs with 60mm diameter and connects via a dedicated cable to the EK-Loop Connect control unit. Technical Specifications: Connectors: 4-pin Length: 50cm
The Lian Li O11D Mini Front MK2 is made of high-quality and transparent acrylic glass, consists of a large chamber and 5 channels. As befits a distro plate, it allows all radiators, as well as GPU and CPU to be connected to each other in the circuit. For this purpose, 12 ports (incl. fill port & drain port) are available. The MK2 replaces the original front panel. The screw points provided by Lian Li can be used for fixing. For compatibility of the Distro Plate with radiators, please note that only (!) "EKWB SE360 (2x)" & "EKWB SE240 (1x)" can be used. In addition to the screw set for fixing the Distro Plate to the housing, the scope of delivery includes a specially developed D5 adapter (WITHOUT PUMP!). The adapter is compatible with every common D5 pump and is decoupled from the Distro Plate. The vibrations of the pump have been reduced to a minimum by means of rubber-mounted sealing rings, which results in less noise pollution. Features at a glance Smallest distro plate in the Lian Li range Unique plug-in system for easy installation in the case Adapter enables perfect fit of a D5 pump Compatible with EK-CoolStream SE360 2x and 1x SE240mm Technical details Material: high-quality acrylic glass, plastic Manufacturing: CNC machining of the acrylic, assembly by hand Dimensions: without pump (W x H x D): 487 x 211 x 21 mm with pump (W x H x D): 487 x 211 x 90 mm Colour: transparent Connections: 12x G1/4 inch connections Capacity: 435 ml Compatibility: 3x360mm fan space Scope of delivery Lian Li Mini MK2 4x M3 glands
Set aus 16 braunen Anti-Vibrations-Befestigungen (Gummi-Entkopplerstifte) von Noctua zur einseitigen und geräuschgeminderten Befestigung von Lüftern am Gehäuse, auch für Slim-Lüfter geeignet
Whether used as a replacement or to modify the tube, the Protium reservoir can be used with all Protium items. Technical Data Length: 100 mm Outer diameter: 60 mm Material: Acrylic Compatibility Protium D5 pump attachment Protium D5/Reservoir Combo Protium reservoir
Kompaktne jõudlus kohtub kaasaegse disainiga; Madala vibratsiooniga, energiasäästliku mootori ja hüdrodünaamilise liugelaagriga ühendavad need vaikse ja tõhusa töö; Ventilaatori kiirust saab PWM-i kaudu dünaamiliselt juhtida; 12 ...
AMD Tower CPU Cooler for Continuous Operation. 200 - 1800 rpm Lüfterlager: Double Ball Bearing Geräuschpegel: 0.35 Sone Stromstärke: 0.12 A Anschluss: 4-Pin Größe & Gewicht Tiefe: 91 mm Breite: 133 mm Höhe: 158.5 mm Gewicht:734 g
Der Arctic Freezer A35 RGB kombiniert Leistung und ein Modernes Design. Die Optimierte Leistung, schwarzes Design und flüsterleiser Betrieb heben den Freezer A35 RGB hervor und bieten ein besseres Erlebnis. Der Freezer A35 RGB wird mit einer 0,8 g Spritze der neuen MX-5 ausgeliefert. ARCTICs Ultimate Performance Wärmeleitpaste ermöglicht aufgrund ihrer geringen Viskosität und Partikelgröße eine besonders dünne Schichtdicke und verringert den Wärmestau zwischen Heatspreader der CPU und Kühler erheblich. Durch sein kompaktes Design ermöglicht er im installierten Zustand uneingeschränkte RAM-Kompatibilität.Der Freezer A35 RGB ist eine sockelspezifische Installationsvariante für AMDs Sockel AM4. Der Freezer A35 RGB verfügt über 12 analoge RGB LEDs, welcher direkt über einen 12 V 4-Piun RGB-Header des Mainboards angeschlossen werden kann. Alternativ kann der Kühler aber auch über einen externen Controller illuminiert und mit der Beleuchtung anderer Hardware synchronisiert werden. Technische Daten: Maße: 124 x 157 x 103 mm (B x H x T) Material: Kupfer (Boden, Heatpipes), Aluminium (Lamellen) Gewicht: ca. 764 g Farbe: Schwarz, Rot Heatpipes: 4x Ø 6 mm Empfohlen für TDP bis: 210 W Lüfter: 2x 120 mm (Max. 0,5 Sone, 200 - 2.100 U/Min) Anschluss: 4-Pin PWM Stromstärke: 0,13 A Spannung: 12 V Kompatibilität: Intel: 1151, 1150, 1155, 1156, 2066, 2011-V3 AMD: AM4
Optimierte Leistung trifft modernes, schwarzes Design und flüsterleisen Betrieb. Der Single-Tower CPU-Kühler ermöglicht mit seinen vier versetzen Heatpipes eine schnelle Wärmeübertragung in den Kühlkörper, wo diese mittels eines 120 mm Lüfter effizient abgeführt werden kann. ULTIMATE PERFORMANCE WÄRMELEITPASTE Der Freezer i35 wird mit einer 0,8 g Spritze der neuen MX-5 ausgeliefert. ARCTICs Ultimate Performance Wärmeleitpaste ermöglicht aufgrund ihrer geringen Viskosität und Partikelgröße eine besonders dünne Schichtdicke und verringert den Wärmestau zwischen Heatspreader der CPU und Kühler erheblich. FÜR KÜHLKÖRPER OPTIMIERTER LÜFTER Der beim Freezer i35 verbaute Lüfter, profitiert von allen Vorzügen der P-Lüfter. Diese vereinen, mit ihrem vibrationsarmen, stromsparenden Motor und dem hydrodynamischen Gleitlager, einen leisen, sowie effizienten Betrieb. Trotz hoher Finnendichte garantiert der Lüfter mit seinem fokussierten Luftstrom einen hohen statischen Druck und ist damit ideal für den Einsatz auf Radiatoren und Kühlkörpern geeignet. Die Drehzahl des Lüfters lässt sich dynamisch über PWM steuern und kann somit optimal an jedes Szenario angepasst werden. Technische Daten: Intel Sockel: 1700, 1200, 115X Heatpipes: 4 Finnenmaterial: Aluminium Finnenanzahl: 54 Finnendicke: 0,4 mm Wärmeleitpaste: MX-5 (0.8g) Lüftergröße: 120 Geschwindigkeit: 200 - 1800 rpm Lüfterlager: Fluid Dynamic Bearing Geräuschpegel: 0.35 Sone Stromstärke: 0.12 A Anschluss: 4-Pin Tiefe: 91 mm Breite: 133 mm Höhe: 158.5 mm Gewicht: 734 g
ROG Strix LC II 280 ARGB AIO delivers high-performance CPU liquid cooling with sleek, modern aesthetics. Featuring a closed-loop design and addressable RGB radiator fans, the cooler unleashes the full potential of an Intel or AMD CPU while further accentuating your build with brilliant multi-color lighting effects. With the cooling you expect from ROG, Strix LC II 280 ARGB is ready to become an essential part of your rig and light it up with your own unique style.
Alphacool’s Eiszapfen Connector Series is the high-end execution of these tried-and-true connectors! Every requirement you could have of a connector is met with this series: highflow, form, processing and colour. A refusal to compromise in development and production has made the Eiszapfen series into what it is. Components are available in brilliant chrome or a deep, matte black, which will fit excellently into any system. A special procedure binds the outer coating firmly to the surface, improving the longevity of the intense colour and preventing any chipping or peeling of the coating. Every connector now has the Alphacool logo, which along with their distinctive shape makes them unmistakable! Anyone looking for colourful options has them: the O-rings in the shipment come in three colours. With the available UV-light option, these will even light up in the corresponding colour. Model: 90° Socket 13/10mm This connector has a ¼” thread on one side and is thereby compatible with 95% of components. The other side fits a 13/10mm hose. The middle of this connector is turned at a 90° angle in order to prevent complicated hose connections. The threaded side is rotatable for maximum flexibility. Technical Specifications: Material: Brass Colour: Chrome Dimensions: Length: 34.5mm Width: 20mm Height: 33mm Scope of Delivery: 1x Alphacool Eiszapfen 13/10mm compression fitting 90° rotatable G1/4 - chrome
Hard Tube Fitting von EK Water Blocks, für Röhren mit 12 mm AD, Kompatibel zu Röhren aus Acryl / PETG / Kupfer / Messing / Edelstahl, mit optionalen Ringen farblich individualisierbar
Kryonaut on professionaalne termopasta, mis on mõeldud kõige nõudlikumatele kasutusvaldkondadele – alates ekstreemsest overclockingust kuni tööstuslike jahutussüsteemideni. Selle erakordne soojusjuhtivus ja kuivamiskindel koostis tagavad maksimaalse jõudluse ka kõrgetel temperatuuridel. • Mõeldud ekstreemseks overclockinguks • Väga kõrge soojusjuhtivus • Ei kuiva ega kõvene • Pikaajaline töökindlus • Ei juhi elektrit
The Eiszapfen PRO hard tube fittings from Alphacool are the next step in development for the familiar Eiszapfen fittings. In the development of the fittings Alphacool concentrated on a specific problem, deforming PETG hard tubes at high temperatures. PETG can start to deform at 60°C. Although such a temperature is usually rarely reached, it can still occur. The Eiszapfen PRO fittings prevent this problem from the outset and hold the tubes in position. The deformation is prevented by the new nylon inserts inside and stabilizes the hard tubes. Furthermore, the fitting still has an O-ring and a compression seal. However, the contact area is much larger than with normal O-rings, which provides a better grip. With the insert and the compression seal, the tube is strengthened from the inside and outside. Even under heavy loads the HardTube does not slip. Alphacool has tested the tensile strength of up to over 8kg, so there is no need to worry about loose tubing. Technical details Material Brass Colour White Hight 23 mm Diameter 26 mm Thread length 5 mm Thread G1/4“ HardTube size 16 mm Compatibility PETG, acrylic, brass and glass tubes Weight 42 g Download Datasheet PDF: Alphacool Eiszapfen PRO 16mm HardTube Fitting G1/4 - White Sixpack Fitting Map: You can find an interactive map of all Alphacool fittings here.
Alphacools's fittings go new ways in looks, quality of manufacturing, colours and choice. The inner diameter of these fittings truly deserves the „high flow“ attribute! The first three colours, Chrome, Deep Black and Shiny Copper offer something for every taste. The product matching series are designed to look elegant in every system, highlighting the individual design of the computer. The limits are endless with these Alphacool fittings in combination with Alphacool tubing! With a new process during chromatising the surface finish is completely connected with the brass body, hence ensuring permanent intense colours and peeling of the chrome layer. The Alphacool name in blue lettering on some of the fittings additionally underlines the individuality of these items. Functionality of this connector:This fitting can be used to connect 16/10mm tubing with a G1/4“ connection thread. The fitting is angled by 45° and is revolvable, allowing easy hose routing in the system. Technical specifications: Material: Brass, chromatizedColour: Chrome Dimensions:Length: 36mm Width: D20mmHeight: 40mm Hose size compatibility : 16/10mm Extent of delivery:1 x Alphacool HF Screw connector 45° G1/4 outer thread on 16/10 revolvable - Chrome This product has been reviewed for you:ModdingbaseXtremesystems (Engl.) (userreview)PT-reviews (Pt)
The Alphacool Eiszapfen is a rotatable 8 mm offset fitting with one internal thread and one external thread that can be easily tied into any water circuit. Integration made easy The offset piece is very compact and can be integrated into any water cooling system thanks to its G1/4" internal and external threads. It is simply screwed onto the corresponding G1/4" connections at the desired position in the water circuit. Design The threads are 5mm deep and 5mm high respectively, thus enabling the very compact design. The offset piece can also be rotated 360°, which provides additional flexibility for integration even in the tightest cases. Coloured O-rings In addition to the standard black O-ring, 3 more O-rings in red, yellow and blue are included.Compatibility:G1/4" OT/IT threads Technical data L x W x H 24 x 22,5 x 18,5mm Material brass Offset 8mm Threads G1/4" IT, G1/4" OT Thread depth 5mm Thread height 5mm Weight 28g Color black
