The Alphacool Eiszyklon Aurora LUX fan impresses with its aRGB LEDs and light defusing areas that distribute the light evenly. It shows its strengths particularly on radiators due to a high static pressure, even if it rotates more slowly. Its maximum speed is 1100 rpm. Due to its naturally decoupled frame, it remains quiet with less vibrations. Unlike many other fans, it has only one cable, which ends with a 6-pin connector. With the Aurora LUX Digital RGB controller from Alphacool, this one cable can be used to regulate the speed as well as adjust the lighting effects and colours. Technical data: Fans Size: 120 x 120 x 25 mm Speed: 1100 rpm Static Pressure: 2.23 mm H2O Air flow rate: 87.32 m³/h Bearings: Hydraulic Fan/ aRGB Connector: 6-Pin Illumination: Digital addressable 5V RGB LEDs Controller Dimensions: 93 x 47 x 17 mm (L x W x H) Fan Connector: 10 x 6-Pin Digital RGB LED Strip Connector: 2x JTS 4-Pin Fan voltage: 12V Digital RGB LED Voltage: 5V Max. Power Output: 50W Control Via: Remote controller Mounting: Adhesive Tape
Optimised for Static Pressure During the development of the new P14 PWM, special emphasis was placed on a focused airstream and thus a high static pressure. The fan guarantees extremely efficient cooling, even with increased air resistance. Therefore, the P14 PWM is particularly suitable for use on heatsinks and radiators. More Efficient Technology The motor is powered by a Neodym-Iron-Boron-Magnet ring of the newest generation, which allows the new P14 PWM to run much more efficiently than its predecessors. This saves energy and lowers the coil temperature without comprimising the performance. Maximum Quietness, Minimum Vibration Even at low speeds the operating sound of the new ARCTIC motor is barely noticeable. Due to a sinus-magnetizing the new motor only creates about 5 % of the vibration from commutation of a regular DC-motor without filter. Consequently, there is no need for rubber spacers due to the steady and smooth torque of the new motor. Extended Life Span A 10 °C lower motor temperature roughly doubles the life span of a fan. The new ARCTIC motor has a four times longer service life through its low coil temperature. Consequently, we have extended the warranty to 10 years. 200 to 1700 RPM regulated via PWM Thanks to the 4-pin connector, the RPM can be regulated in a broad spectrum via PWM. In this way, noise is kept at a minimum while maximum cooling performance is guaranteed when needed. High Quality Bearing Thanks to an alloy/lubricant combination developed in Germany, friction within the bearing is reduced and greater efficiency is achieved. As a result, there is less heat development as well as less bearing noise, which means you can enjoy a longer service life from your fan. Technical Data: Performance Fan Speed: 200 - 1700 rpm Airflow: 72.8 CFM/ 123.76 m³/h Static Pressure: 2,40 (mm/H2O) Noise Level: 0.3 Sone Fan Fan Frame: Standard Controll Typ: PWM Connector: 4-Pin Connector Fan Bearing: Fluid Dynamic Bearing Electric Characteristics Typical Voltage: 12 V DC Starting Voltage: 3.9 V Current: 0.12 A Cable Lenght: 400 mm Size & Weight Lenght: 140 mm Width: 140 mm Height: 27 mm Weight: 194 g
The ICEBERG THERMAL DRIFTIce Thermal Pad by Iceberg Thermal is designed to efficiently dissipate heat and enhance the performance of your electronic devices. Measuring 40mm by 80mm with a thickness of 1.0mm, this thermal pad is perfect for a variety of applications. It is lightweight, with a gross weight of only 0.020 kg, making it easy to handle and install. Ensure your devices remain cool and functional with this high-quality thermal pad.
The ICEBERG THERMAL DRIFTIce Thermal Pad by Iceberg Thermal is an effective solution for heat management in electronic devices. Measuring 40mm by 120mm with a thickness of 1.5mm, this thermal pad provides optimal thermal conductivity to improve device performance. It is lightweight, with a gross weight of only 0.035 kg, making it easy to handle and install. Ideal for a variety of applications, this thermal pad ensures efficient heat dissipation, protecting components from overheating.
The Lian Li O11D Mini Front MK2 is made of high-quality and transparent acrylic glass, consists of a large chamber and 5 channels. As befits a distro plate, it allows all radiators, as well as GPU and CPU to be connected to each other in the circuit. For this purpose, 12 ports (incl. fill port & drain port) are available. The MK2 replaces the original front panel. The screw points provided by Lian Li can be used for fixing. For compatibility of the Distro Plate with radiators, please note that only (!) "EKWB SE360 (2x)" & "EKWB SE240 (1x)" can be used. In addition to the screw set for fixing the Distro Plate to the housing, the scope of delivery includes a specially developed D5 adapter (WITHOUT PUMP!). The adapter is compatible with every common D5 pump and is decoupled from the Distro Plate. The vibrations of the pump have been reduced to a minimum by means of rubber-mounted sealing rings, which results in less noise pollution. Features at a glance Smallest distro plate in the Lian Li range Unique plug-in system for easy installation in the case Adapter enables perfect fit of a D5 pump Compatible with EK-CoolStream SE360 2x and 1x SE240mm Technical details Material: high-quality acrylic glass, plastic Manufacturing: CNC machining of the acrylic, assembly by hand Dimensions: without pump (W x H x D): 487 x 211 x 21 mm with pump (W x H x D): 487 x 211 x 90 mm Colour: transparent Connections: 12x G1/4 inch connections Capacity: 435 ml Compatibility: 3x360mm fan space Scope of delivery Lian Li Mini MK2 4x M3 glands
Whether used as a replacement or to modify the tube, the Protium reservoir can be used with all Protium items. Technical Data Length: 100 mm Outer diameter: 60 mm Material: Acrylic Compatibility Protium D5 pump attachment Protium D5/Reservoir Combo Protium reservoir
Der Arctic Freezer A35 RGB kombiniert Leistung und ein Modernes Design. Die Optimierte Leistung, schwarzes Design und flüsterleiser Betrieb heben den Freezer A35 RGB hervor und bieten ein besseres Erlebnis. Der Freezer A35 RGB wird mit einer 0,8 g Spritze der neuen MX-5 ausgeliefert. ARCTICs Ultimate Performance Wärmeleitpaste ermöglicht aufgrund ihrer geringen Viskosität und Partikelgröße eine besonders dünne Schichtdicke und verringert den Wärmestau zwischen Heatspreader der CPU und Kühler erheblich. Durch sein kompaktes Design ermöglicht er im installierten Zustand uneingeschränkte RAM-Kompatibilität.Der Freezer A35 RGB ist eine sockelspezifische Installationsvariante für AMDs Sockel AM4. Der Freezer A35 RGB verfügt über 12 analoge RGB LEDs, welcher direkt über einen 12 V 4-Piun RGB-Header des Mainboards angeschlossen werden kann. Alternativ kann der Kühler aber auch über einen externen Controller illuminiert und mit der Beleuchtung anderer Hardware synchronisiert werden. Technische Daten: Maße: 124 x 157 x 103 mm (B x H x T) Material: Kupfer (Boden, Heatpipes), Aluminium (Lamellen) Gewicht: ca. 764 g Farbe: Schwarz, Rot Heatpipes: 4x Ø 6 mm Empfohlen für TDP bis: 210 W Lüfter: 2x 120 mm (Max. 0,5 Sone, 200 - 2.100 U/Min) Anschluss: 4-Pin PWM Stromstärke: 0,13 A Spannung: 12 V Kompatibilität: Intel: 1151, 1150, 1155, 1156, 2066, 2011-V3 AMD: AM4
Kompaktne jõudlus kohtub kaasaegse disainiga; Madala vibratsiooniga, energiasäästliku mootori ja hüdrodünaamilise liugelaagriga ühendavad need vaikse ja tõhusa töö; Ventilaatori kiirust saab PWM-i kaudu dünaamiliselt juhtida; 12 ...
AMD Tower CPU Cooler for Continuous Operation. 200 - 1800 rpm Lüfterlager: Double Ball Bearing Geräuschpegel: 0.35 Sone Stromstärke: 0.12 A Anschluss: 4-Pin Größe & Gewicht Tiefe: 91 mm Breite: 133 mm Höhe: 158.5 mm Gewicht:734 g
Optimierte Leistung trifft modernes, schwarzes Design und flüsterleisen Betrieb. Der Single-Tower CPU-Kühler ermöglicht mit seinen vier versetzen Heatpipes eine schnelle Wärmeübertragung in den Kühlkörper, wo diese mittels eines 120 mm Lüfter effizient abgeführt werden kann. ULTIMATE PERFORMANCE WÄRMELEITPASTE Der Freezer i35 wird mit einer 0,8 g Spritze der neuen MX-5 ausgeliefert. ARCTICs Ultimate Performance Wärmeleitpaste ermöglicht aufgrund ihrer geringen Viskosität und Partikelgröße eine besonders dünne Schichtdicke und verringert den Wärmestau zwischen Heatspreader der CPU und Kühler erheblich. FÜR KÜHLKÖRPER OPTIMIERTER LÜFTER Der beim Freezer i35 verbaute Lüfter, profitiert von allen Vorzügen der P-Lüfter. Diese vereinen, mit ihrem vibrationsarmen, stromsparenden Motor und dem hydrodynamischen Gleitlager, einen leisen, sowie effizienten Betrieb. Trotz hoher Finnendichte garantiert der Lüfter mit seinem fokussierten Luftstrom einen hohen statischen Druck und ist damit ideal für den Einsatz auf Radiatoren und Kühlkörpern geeignet. Die Drehzahl des Lüfters lässt sich dynamisch über PWM steuern und kann somit optimal an jedes Szenario angepasst werden. Technische Daten: Intel Sockel: 1700, 1200, 115X Heatpipes: 4 Finnenmaterial: Aluminium Finnenanzahl: 54 Finnendicke: 0,4 mm Wärmeleitpaste: MX-5 (0.8g) Lüftergröße: 120 Geschwindigkeit: 200 - 1800 rpm Lüfterlager: Fluid Dynamic Bearing Geräuschpegel: 0.35 Sone Stromstärke: 0.12 A Anschluss: 4-Pin Tiefe: 91 mm Breite: 133 mm Höhe: 158.5 mm Gewicht: 734 g
With the Core Ocean AiO, Alphacool presents an all-in-one solution that, thanks to its excellent price-performance ratio, enables entry into performance-oriented CPU water cooling. The difference to the Eisbaer CPU AiO is that the Ocean All-in-One is not expandable. Adding further components such as GPU coolers, radiators or expansion tanks is not intended here. But also not necessary! The choice of components and the design of the Core Ocean enable a long service life with low maintenance for water cooling of all common mainstream sockets from AMD and Intel. Aluminium Radiator Compared to Alphacool's full copper models, the T38 aluminium radiator has additional cooling channels. This technical design allows a significant increase in cooling capacity without restricting the water flow within the radiator. Due to the low height of 38mm, the radiator with single-sided fan assembly fits into the tightest case and enables high-performance water cooling of the CPU. Core fan The fan can be regulated from 0 to 2000 rpm via the 4-pin PWM connection. The cable is 40cm long. This allows the fan to be connected to the mainboard or a special controller without the need for additional adapter cables or extensions. At 2000 rpm, it provides an air flow of 92.3 CFM, together with a high static pressure of 2.53mm/H2O. This makes the fan perfect for mounting on radiators of a water cooling system. Cooler & Pump As with all Alphacool products, the radiator base is made of copper and is equipped with very fine cooling fins distributed over the entire base. A nozzle plate ensures an accelerated flow over the cooling fins, which increases the cooling performance. The water flow is optimised so that all areas of the cooler base are cooled evenly. The cooler is compatible with all common mainstream sockets from AMD and Intel. The built-in pump has a speed range of 2500 - 3500 RPM (+/- 10%) and can be controlled via PWM. The pump is connected to the mainboard or to an external controller via the existing 4-pin fan connector. This allows the speed range of the pump to be controlled and monitored. Hoses & Connections The FEP hoses are 40cm long, sleeved and very flexible. The rotatable 360° connections to the cooler and to the radiator are permanently installed and cannot be replaced. However, the combination of hoses and connectors allows a very variable positioning of the AiO even in the tightest PC case. Illumination 12 digitally addressable 5V RGB LEDs are installed in the pump housing, which create a unique, very noble-looking illumination. The digital aRGB LED lighting is connected via a JST 3-pin connector. To control the lighting, the 3-pin female connector must be connected to a digital RGB controller (not included) or a digital RGB-capable mainboard. Additional digital RGB LEDs can be connected to the remaining 3-pin male connector. Thermal compound The thermal paste included in the delivery has a thermal conductivity of 7.5 W/mK. The thermal grease does not harden, is particularly suitable for high contact pressures and can be applied perfectly due to the optimally selected viscosity. Compatibility: Intel: LGA 115x / LGA 1200 / LGA 1700 / LGA 2066 AMD: AM4 / AM5 Technical data radiator L x W x H 460 x 140 x 38mm Material cooling fins, channels & prechamber 3003 Aluminium Material outer housing & threads 3003 Aluminium Fins per Inch 20 Fan size 140mm Fan slots 3 one-sided / 6 double-sided Color black Technical data fans L x W x H 140 x 140 x 25mm Bearing Type hydraulic Bearing Rated Voltage DC 12V Operating Voltage DC 7-14V Start-up Voltage 7V Rated Current 0.26 (Max. 0.3) A Rated Power 3.12 (Max. 3.6) W Rated Speed 0 - 2000rpm/min (±10%) Max. Air Flow 92.3CFM Max.Static Pressure 2.53mm-H2O Noise level (rated voltage, mute room, distance 1m) 34.3 (Max. 36) dBA MTBF 50000hrs at 25°C Speed Control Mode PWM Connection & control 4-pin PWM (cable 40cm) Auto-Restart yes Tachometer Output yes Color black Technical data cooler & pump L x W x H 70,2 x 70,2 x 46mm Material cooler bottom copper Material pump housing Synthetic material (ABS+PC) Fin structure cooler bottom 0,1 x 0,1mm Material pump bearing & shaft ceramics Starting voltage > DC 6V Rated power 7.1W Noise level 35Db Rated Current 0.59A (±10% MAX) Speed 2500~3500 (±10% RPM) Power supply Digital aRGB 3-pin 5V (male & female, cable length 30cm) Number of aRGB LEDs 12 Power supply pump 4-Pin JST (Kabellänge 30cm) Technical data tubes Material FEP, black with weave cover Length 400mm
Alphacool’s Eiszapfen Connector Series is the high-end execution of these tried-and-true connectors! Every requirement you could have of a connector is met with this series: highflow, form, processing and colour. A refusal to compromise in development and production has made the Eiszapfen series into what it is. Components are available in brilliant chrome or a deep, matte black, which will fit excellently into any system. A special procedure binds the outer coating firmly to the surface, improving the longevity of the intense colour and preventing any chipping or peeling of the coating. Every connector now has the Alphacool logo, which along with their distinctive shape makes them unmistakable! Anyone looking for colourful options has them: the O-rings in the shipment come in three colours. With the available UV-light option, these will even light up in the corresponding colour. Model: 90° Socket 13/10mm This connector has a ¼” thread on one side and is thereby compatible with 95% of components. The other side fits a 13/10mm hose. The middle of this connector is turned at a 90° angle in order to prevent complicated hose connections. The threaded side is rotatable for maximum flexibility. Technical Specifications: Material: Brass Colour: Chrome Dimensions: Length: 34.5mm Width: 20mm Height: 33mm Scope of Delivery: 1x Alphacool Eiszapfen 13/10mm compression fitting 90° rotatable G1/4 - chrome
Hard Tube Fitting von EK Water Blocks, für Röhren mit 12 mm AD, Kompatibel zu Röhren aus Acryl / PETG / Kupfer / Messing / Edelstahl, mit optionalen Ringen farblich individualisierbar
Kryonaut on professionaalne termopasta, mis on mõeldud kõige nõudlikumatele kasutusvaldkondadele – alates ekstreemsest overclockingust kuni tööstuslike jahutussüsteemideni. Selle erakordne soojusjuhtivus ja kuivamiskindel koostis tagavad maksimaalse jõudluse ka kõrgetel temperatuuridel. • Mõeldud ekstreemseks overclockinguks • Väga kõrge soojusjuhtivus • Ei kuiva ega kõvene • Pikaajaline töökindlus • Ei juhi elektrit
Alphacool’s Eiszapfen Connector Series is the high-end execution of these tried-and-true connectors! Every requirement you could have of a connector is met with this series: highflow, form, processing and colour. A refusal to compromise in development and production has made the Eiszapfen series into what it is. Components are available in brilliant chrome or a deep, matte black, which will fit excellently into any system. A special procedure binds the outer coating firmly to the surface, improving the longevity of the intense colour and preventing any chipping or peeling of the coating. Every connector now has the Alphacool logo, which along with their distinctive shape makes them unmistakable! Anyone looking for colourful options has them: the O-rings in the shipment come in three colours. With the available UV-light option, these will even light up in the corresponding colour. Model: 45° Angle Adapter This adapter has a rotatable ¼” external screw thread on one side and a ¼” internal thread on the other side. This 45° angle connector is mostly useful in cases where ¼” threads are too close to one another and larger hose connections do not fit next to each other. Technical Specifications: Material: Brass Colour: Deep Black Dimensions: Length: 35mm Diameter: 18,5mm Scope of Delivery: 1x Alphacool Eiszapfen angled adaptor 45° rotatable G1/4 outer thread to G1/4 inner thread - deep black Fitting Map You can find an interactive map of all alphacool fittings here.
The Alphacool Eiszapfen is a rotatable 8 mm offset fitting with one internal thread and one external thread that can be easily tied into any water circuit. Integration made easy The offset piece is very compact and can be integrated into any water cooling system thanks to its G1/4" internal and external threads. It is simply screwed onto the corresponding G1/4" connections at the desired position in the water circuit. Design The threads are 5mm deep and 5mm high respectively, thus enabling the very compact design. The offset piece can also be rotated 360°, which provides additional flexibility for integration even in the tightest cases. Coloured O-rings In addition to the standard black O-ring, 3 more O-rings in red, yellow and blue are included.Compatibility:G1/4" OT/IT threads Technical data L x W x H 24 x 22,5 x 18,5mm Material brass Offset 8mm Threads G1/4" IT, G1/4" OT Thread depth 5mm Thread height 5mm Weight 28g Color black
Alphacool's Eiszapfen connector series is the high-end execution of these tried-and-true fittings! Everything you want in a compression fitting is here: highflow, form, processing and colour. A refusal to compromise in development and production has made the Eiszapfen series into what it is. Fittings are available in brilliant chrome or a deep, matte black, which will fit excellently into any system. A special procedure binds the outer coating firmly to the surface, improving the longevity of the intense colour and preventing any chipping or peeling of the coating. Every connector now has the Alphacool logo, which along with their distinctive shape makes them unmistakable! The union nut's slanted corners allow the O-ring to be pressed firmly against the HardTube, ensuring it sits even more securely than before. This allows for greater safety in transport. Model: 90° compression fitting 13mmThis fitting has a 1/4" thread on one side and is thereby compatible with 95% of components. The other side fits a 13mm acrylic or brass tube. This fitting is bent 90° in the middle to avoid complicated hose connections. The threaded side is rotatable for maximum flexibility. Technical Specifications Material: brass Colour: chrome Dimensions Length: 42.5mm Width: 21mm Scope of Delivery 1x Alphacool Eiszapfen 13mm HardTube compression fitting 90° rotatable G1/4 for plexi- brass tubes - chrome Fitting MapYou can find an interactive map of all Alphacool fittings here.
The new Eiszapfen PRO hard tube fittings from Alphacool are the next step in development for the familiar Eiszapfen fittings. In the development of the fittings Alphacool concentrated on a specific problem, deforming PETG hard tubes at high temperatures. PETG can start to deform at 60°C. Although such a temperature is usually rarely reached, it can still occur. The Eiszapfen PRO fittings prevent this problem from the outset and hold the tubes in position. The deformation is prevented by the new nylon inserts inside and stabilizes the hard tubes. Furthermore, the fitting still has an O-ring and a compression seal. However, the contact area is much larger than with normal O-rings, which provides a better grip. With the insert and the compression seal, the tube is strengthened from the inside and outside. Even under heavy loads the HardTube does not slip. Alphacool has tested the tensile strength of up to over 8kg, so there is no need to worry about loose tubing. Technical details: Material: brass Colour: chrome Diameter: 26 mm Height: 23 mm Thread: G1/4" Thread length: 5 mm HardTube size: 16 mm Compatibility: PETG, acrylic, brass and glass tubes Weight: 0,042 kg Scope of supply: 1x Alphacool Eiszapfen PRO 16 mm HardTube Fitting G1/4 - Chrome Sixpack
Drehbarer T-Splitter-Adapter von EK Water Blocks, Teil der EKWB Quantum-Linie, zur Verbindung von einem G1/4-Zoll-Außen- mit zwei G1/4-Zoll-Innengewinden
Alphacool's Eiszapfen is the high-end version of the already proven connectors and meets all the requirements placed on a connector with its high-flow, shape, processing and colour. Compatibility This adapter has a rotatable ¼” external screw thread on one side and a ¼” internal thread on the other side. This 45° angle connector is mostly useful in cases where ¼” threads are too close to one another and larger hose connections do not fit next to each other. Design With brilliant chrome, deep matt black and decent matt white, three colour variants are available that fit perfectly into any system. Thanks to special processes, the coatings are firmly bonded to the substrate. This ensures a high longevity of the colours and prevents the coating from flaking off. The connector now also has the Alphacool logo, which makes it unique in addition to its special shape! Technical details Material Brass Colour White Length 35 mm Diameter 18 mm Thread G1/4“ Thread length 5 mm Weight 34 g Download Datenblatt PDF: Alphacool Eiszapfen angled adaptor 45° rotatable G1/4 outer thread to G1/4 inner thread - White Fitting Map: You can find an interactive map of all Alphacool fittings here.
