Võrguseadmed

This cable by Delock is used to extend a serial connection and can be used to connect various devices with D-Sub 25 pin connector.     Specification • Connectors:   1 x D-Sub 25 pin male >   1 x D-Sub 25 pin female • Connectors with screws • Pin assignment: 1:1 • Cable gauge: 28 AWG • Cable diameter: ca. 7 mm • Operating temperature: 0 °C ~ 50 °C • Fire-resistance rating: VW-1 • Length incl. connectors: ca. 20 m • Colour: beige   System requirements • A free D-Sub 25 pin female   Package content • Serial cable

Delock FireWire PCI-kaart laiendab arvutit kolme välise FireWire pordi ja ühe sisemise FireWire pordi võrra. Selle kaardiga saab ühendada erinevaid FireWire seadmeid, nagu välised kõvakettad, CDR- ja CDRW-draivid, videokaamerad jne. Kasutades kaasasolevat madala profiiliga klambrit, saab PCI-kaardi paigaldada ka Mini-PC-sse.   Spetsifikatsioon • Ühendus:   väline:     3 x FireWire 1394A 6 kontaktiga emane   sisemine:     1 x FireWire 1394A 6 kontaktiga emane (jagatud 1. välise FireWire pordiga)     1 x 32-bitine PCI standard 2.2 • Kiibistik: LSI L-FW323-07 • Andmeedastuskiirus kuni 400 Mbps • Toetab OHCI spetsifikatsioone V1.0 ja 1.1 • Hot Plug, Plug & Play

See Delocki aktiivne DAB+ antenn on mõeldud digitaalringhäälingu DIGITAALRADIO vastuvõtmiseks. Integreeritud võimendi parandab vastuvõtusignaali täiendavalt.     Spetsifikatsioon - Ühendus: 1 x SMB-pistik - Sagedusvahemik: 174 - 240 MHz - Antenni võimendus: 23 dBi - Impedants: 50 Ohm - VSWR: 2,0 - Tööpinge: 5 V - Voolutarve: ca. 13-19 mA - Töötemperatuur: -10 °C ~ 70 °C - Kaabli tüüp: RG-174 - Kaabli läbimõõt: ca. 2,7 mm - Kaabli pikkus: ca 3 m - Antennivarda mõõtmed (LxSxK): ca. 18,40 x 1,30 x 0,36 cm     Süsteeminõuded - DAB+ vastuvõtja vaba SMB-portiga     Pakendi sisu - DAB+ antenn 

See kaabel saab toita kahte SATA-seadet ühe vaba 15-pini SATA-pistiku toitepistiku kaudu. Spetsifikatsioon - Liitmik: 1 x SATA 15-pini pistik > 2 x SATA 15-pini pistikupesa - 5 juhtmega versioon (kollane = 12 V, must = GND, punane = 5 V, oranž = 3,3 V). - Kaabli gabariit: 18 AWG - Pikkus ilma pistikuta: ca 15 cm Süsteeminõuded - Toiteallikas, millel on vaba SATA-toiteühendus Pakendi sisu - Toitejuhe

See Delocki 4-pini ventilaatorikaabel PWM-toega võimaldab ventilaatori ühendust laiendada. 4-pini ventilaatori pistikupesa sobib ka 3-pini ventilaatori pistiku ühendamiseks ilma PWM-toeta.     Spetsifikatsioon - Pistikud:   1 x 4-pini ventilaatori pistikupesa isane >   1 x 4-pini ventilaatori pistikupesa (emane) - Kaabli gabariit: 22 AWG - PWM-juhe (impulsslaiendus) - Pikkus koos pistikutega: ca. 10 cm     Süsteeminõuded - Põhiplaat vaba 4-pini liidesega     Pakendi sisu - Ventilaatori pikenduskaabel

See Delocki 4-pini ventilaatorikaabel PWM-toega võimaldab ventilaatori ühendust laiendada. 4-pini ventilaatori pistikupesa sobib ka 3-pini ventilaatori pistiku ühendamiseks ilma PWM-toeta.     Spetsifikatsioon - Pistikud:   1 x 4-pini ventilaatori pistikupesa isane >   1 x 4-pini ventilaatori pistikupesa (emane) - Kaabli gabariit: 22 AWG - PWM-juhe (impulsslaiendus) - Pikkus koos pistikutega: ca. 100 cm     Süsteeminõuded - Põhiplaat vaba 4-pini liidesega     Pakendi sisu - Ventilaatori pikenduskaabel

Moxa Wall mounting kit, 51mm wide

Dual RS-485 remote I/O with built-in repeater Supports the installation of multidrop communications parameters Install communications parameters and upgrade firmware via USB Upgrade firmware through an RS-485 connection Wide operating temperature models available for -40 to 85°C (-40 to 185°F) environments The ioLogik R1200 Series RS-485 serial remote I/O devices are perfect for establishing a cost-effective, dependable, and easy-to-maintain remote process control I/O system. Remote serial I/O products offer process engineers the benefit of simple wiring, as they only require two wires to communicate with the controller and other RS-485 devices while adopting the EIA/TIA RS-485 communication protocol to transmit and receive data at high speed over long distances. In addition to communication configuration by software or USB and dual RS-485 port design, Moxa’s remote I/O devices eliminate the nightmare of extensive labor associated with the setup and maintenance of data acquisition and automation systems. Moxa also offers different I/O combinations, which provide greater flexibility and are compatible with many different applications. Easy-to-Use Software Interface for Easy Maintenance With Moxa’s easy-to-use ioSearch software, you can quickly access all of an ioLogik R1200 device’s status information and settings with a user-friendly graphical user interface. Furthermore, ioSearch also provides an easy method for updating firmware for all ioLogik R1200 devices over an RS-485 network, so you can even update your firmware remotely. The free and easy-to-use ioSearch software reduces the maintenance time and labor required to set up your communication interface. When more than one ioLogik R1200 are on the same RS-485 network, you no longer need to turn hundreds of dials during setup. Instead, simply configure and duplicate each ioLogik R1200’s baudrate and mode through the graphical user interface. This convenient software feature reduces maintenance engineers' effort, and greatly simplifies upgrading your device's configuration compared with more traditional methods. Innovative Hardware Design Reduces Deployment Effort and Enhances Maintenance Efficiency With the industry’s first RS-485 serial remote I/O with USB design, Moxa provides an innovative solution for upgrading and configuring RS-485 remote I/O communication devices and firmware. All you need to do is upload the configurations to a USB drive, plug it into the field device, and all the configurations and firmware updates will upload to the field device automatically. Cost-Saving Hardware Design for Backup and Redundancy Moxa’s ioLogik R1200 Series provides dual RS-485 ports so that when one of your RS-485 ports is damaged, you can quickly switch to the other RS-485 port for quick testing or repair. RS-485 remote I/O devices are already considered a low-cost technology, but with dual RS-485 ports, Moxa helps you save a little bit more. With the ioLogik R1200, you can take advantage of our dual RS-485 ports to set up wiring, provide computer redundancy, or back up your network using two computer topologies. For wiring redundancy, when your computer detects that one of the RS-485 connections is not responding, it can quickly switch over to the other RS-485 line to guarantee continuous communication between field sensors and the central computer. Furthermore, users have the freedom to define the settings. For computer redundancy, the ioLogik R1200 provides system operators with a secure backup when one system goes down.

Features and Benefits Protocol conversion between PROFIBUS and Modbus TCP Supports PROFIBUS DP V1 master Supports Modbus TCP client/server Automatic scan of PROFIBUS devices and easy configuration Web-based GUI for I/O data visualization Embedded traffic monitoring/diagnostic information for easy troubleshooting Status monitoring and fault protection for easy maintenance Supports redundant dual DC power inputs and 1 relay output -40 to 75°C wide operating temperature models available Serial port with 2 kV isolation protection Security features based on IEC 62443 Introduction The MGate 5101-PBM-MN gateway provides a communication portal between PROFIBUS devices (e.g. PROFIBUS drives or instruments) and Modbus TCP hosts. All models are protected with a rugged metallic casing, DIN-rail mountable, and offer optional built-in optical isolation. The PROFIBUS and Ethernet status LED indicators are provided for easy maintenance. The rugged design is suitable for industrial applications such as oil/gas, power, process automation, and factory automation. Windows Utility for Easy Configuration and Traffic Monitoring The MGate Manager utility provides a user-friendly interface to make configuration and operation as easy as possible. Moxa’s innovative AutoScan function can automatically detect all connected PROFIBUS slave devices and their available I/O modules to quickly complete gateway configuration, after which an easy-to-read data mapping table is created to assist in the configuration of Modbus TCP master (e.g., SCADA, PLC) settings. In addition, users can configure import/export maintenance functions, and use embedded monitoring tools to maintain logs of Modbus communication packets, which can be used for troubleshooting. A Variety of Maintenance Functions The MGate 5101-PBM-MN provides a Web console and Telnet console for remote maintenance, with both consoles supporting encryption commutation functions such as HTTPS and SSH for preventing unauthorized access. The log functions are provided in firmware such as connection event of Modbus or PROFIBUS for maintenance. Users can monitor each I/O data and review the log through the web console remotely. A relay output alarm is provided for the power input status. It gives maintenance engineers an additional tool for troubleshooting and maintenance. Redundant Power Inputs The MGate 5101-PBM-MN has dual power inputs for greater reliability. The power inputs allow simultaneous connection to 2 live DC power sources to provide uninterrupted operation even if one power source fails. The higher level of reliability makes these advanced PROFIBUS-master-to-Modbus-TCP gateways ideal for demanding industrial applications.

Seda Delocki juhtmega USB-viipkoodiskannerit saab ühendada arvuti või sülearvuti vabasse USB-A-tüüpi emasportti. Selle lineaarse vöötkoodiskänneri laserklassi 1 ja selle lineaarse CMOS-pildianduri abil saab kõiki levinud 1D-vöötkooditüüpe täpselt tuvastada isegi pikkade vahemaade tagant. Lisaks suudab see pihuarvuti vöötkoodiskanner lugeda ekraanidel ja monitoridel kuvatavaid vöötkoode. Skanner kohandab end automaatselt vastavalt ümbritseva keskkonna heledusele ja võtab optimaalsetes valgustingimustes kuni 280 skaneeringut sekundis. Vähese ümbritseva valguse korral valgustab vöötkoodi täiendav valge LED ja seda saab kasutada vähese valguse korral. Tänu kasutatud lasertehnoloogiale on laservalgus inimsilmale kahjutu.     Spetsifikatsioon - Liitmik: 1 x USB tüüp A isane - Resolutsioon: 1: 0,0762 mm - Käiviti: skaneerimisnupp - Lugemiskaugus: ca. 25 mm kuni 507 mm - Valgusallikas: laserklass 1, 650 nm - Valguse värvus: nähtav laser punane - Kompensatsioonivalgus: Valge LED - Andur: lineaarne CMOS-pildiandur - Skaneerimiskiirus: kuni 280 skaneerimist sekundis - Skaneerimisnurk: 41° - Ümbritsev heledus: max. 50000 luksi - Sisendpinge: 5 V - Voolutarve: V 5   töö: max. 160 mA   ooterežiim: max. 80 mA - Töötemperatuur: 0 °C ~ 40 °C - Säilitustemperatuur: -10 °C ~ 60 °C - Suhteline õhuniiskus: 0 - 95 % (ei kondenseeru) - Värv: must/hall - Kaal: umbes 170 g - Mõõtmed (LxSxK): ca. 156 x 71 x 91 mm - Kaabli pikkus: ca. 2 m - Skaneerimiskoodid:    UPC-A / UPC-E   EAN-8 / EAN-13   Maatriks 2 5-st   Hiina postikood (Toshiba kood)   Tööstuslik 2 5-st   Interleaved 2 of 5   Codabar   Kood 11   Kood 32   Standardkood 39   Täielik ASCII-kood 39   Kood 93   Kood 128   EAN / UCC 128   MSI Plessey kood   UK Plessey kood   Telepen kood   GS1 Databar   IATA kood     Süsteeminõuded - Linux 4.4 või uuem - Windows 7/7-64/8.1/8.1-64/10/10-64 - Arvuti või sülearvuti, millel on vaba USB A-tüüpi port     Pakendi sisu - Vöötkoodi skanner - Kasutusjuhend

Seda Delocki klemmiplokkkaablit saab kasutada paljaste juhtmete ühendamiseks. Seega ei ole see kaabel mugav mitte ainult spetsiaalsetes tööstuslikes rakendustes, vaid ka hobi valdkonnas, nt raudteemudelisatsioonis. Kaablile saab ühendada erinevaid seadmeid, millel on sobiv alalisvoolu toitepistik ja mis saavad eraldi toite (sõltuvalt seadme nõuetest).     Spetsifikatsioon - Pistikud:   1 x DC 5,5 x 2,5 mm isane nurkjas >   2 x avatud juhtmed - Positiivne poolus sees, negatiivne poolus väljas - Pinge: max. 12 ~ 36 V - Vool: max. 5 A - Kaabli gabariit: 23 AWG - Alalisvoolu poldi pikkus: ca. 9,5 mm - Pikkus ilma pistikuteta: ca. 50 cm     Süsteeminõuded - Vaba alalisvoolupesa 5,5 x 2,5 x 9,5 mm     Pakendi sisu - Kaabel