The UFiber splitter carries data from a UFiber OLT’s long-haul cable and shares it with multiple UFiber ONUs. Available with 4, 8, 16, or 32 outputs. PLC Splitters UF-SPLITTER-4 UF-SPLITTER-8 UF-SPLITTER-16 UF-SPLITTER-32 Input (1) SC/APC (1) SC/APC (1) SC/APC (1) SC/APC Outputs (4) SC/APC (8) SC/APC (16) SC/APC (32) SC/APC Insertion Loss with Connectors 7.4 dB 10.5 dB 13.7 dB 17.0 dB Uniformity Loss 0.6 dB 0.8 dB 1.2 dB 1.5 dB Polarization Dependent Loss 0.3 dB 0.3 dB 0.3 dB 0.3 dB Wavelength Bandwidth 1260-1650 nm 1260-1650 nm 1260-1650 nm 1260-1650 nm Return Loss (All Ports) 50 dB 50 dB 50 dB 50 dB Directivity 55 dB 55 dB 55 dB 55 dB Fiber Type G657A1 G657A1 G657A1 G657A1 Operating Temperature -40 to 85° C (-40 to 185° F) -40 to 85° C (-40 to 185° F) -40 to 85° C (-40 to 185° F) -40 to 85° C (-40 to 185° F) Total Length 4.06m (13.32') 4.06 m (13.32') 4.06 m (13.32') 4.08 m (13.39') Weight 58 g (2.0 oz) 62 g (2.2 oz) 110 g (3.9 oz) 160 g (5.6 oz)
Tootegrupp: SWITCH - unmanaged LAN võrguseade arhitektuur: GigabitEthernet koos PoE 1000BaseT (RJ45) ports: 8 tk Toetatud protokollid ja standardid: PoE - Power over Ethernet võrgukiht: 2 arvutikorpuse tüüp: metal maksimaalne energiatarbimine: 60 vatti Standard tarvikud: toiteplokk Lisaandmed: väljund pinge värv: must andmeleht: Vendor Page
Tootja: Intellinet võrguseade Solutions Tootegrupp: PoE toiteplokk pakkuja tüüp: Power over Ethernet Injector sisendpinge: 230 V AC väljundpinge: 44 V DC, 57 V DC Real power: 30 vatti Toetatud protokollid ja standardid: IEEE 802.3af - Power over Ethernet, IEEE 802.3at - Power over Ethernet+, IEEE 802.3 - 10BaseT, IEEE 802.3ab - 1000BaseT, IEEE 802.3u - 100BaseTX Lisaandmed: 1 RJ-45 1000 Mbps input port, 1 RJ-45 1000 Mbps data ja power väljund ports, 1 toide ühenduspesa (3 pin) kõrgus: 35 mm laius: 172 mm sügavus: 154 mm
Ubiquiti Recessed ceiling mount accessory for the UVC-G3-FLEX camera. Mount your camera inside the ceiling or a ceiling tile for a clean, low-profile installation. Includes mounting hardware for drywall, solid surface, or ceiling tile installation. Optional security screw locks the camera to the mount from above for added security. 3-Pack* - UVC-G3-Flex camera is shown for demonstration purposes only and sold separately!
Tootja: Lanberg Tootegrupp: Patchcord võrguseade kaabel Wiring type: Cat6 pikkus: 3 m Category: 6 1-ühenduse tüüp: 1 x RJ45 male 2-ühenduse tüüp: 1 x RJ45 male Cross-Over: Jah värv: hall
4 x Gigabit PoE+ ports 1 x Gigabit port 120W PoE power budget 10Gbps switching capacity Supports jumbo frames up to 9KB Hardened IP30 rated metal housing Includes DIN-Rail bracket and magnetic wall mount kit Operating temperature range of -40° – 75° C (-40° – 167° F) Redundant power inputs with overload current protection Alarm relay triggered by power failure Power supply sold separately (models: TI-S12048, TI-S24048, and 48VDC3000)
Integrated multi-band LTE omni antenna + WiFi omni antenna + place to install Teltonika RUT240 or 230 (All-in-one) QuSpot omni LTE antenna for Teltonika RUT240 or 230 router is a perfect outdoor device for mobile and fixed installations like industrial, CCTV, hotspots, yachts, boats, campers, RV etc. It has embedded also omni Wi-Fi antenna. If you use RUT240 or 230 with QuSpot antenna, you get an integrated complete solution with embedded router and multi band antennas in one enclosure. NOTE: For RUT230 one LTE antenna is unplugged. All antennas and Teltonika router integrated in one enclosure Outdoor antenna works in any weather conditions, IP67 Antenna perfectly matched with the router Passive PoE support
8 x Gigabit ports 2 x SFP slots Supports 100/1000Base-FX fiber SFP modules 20Gbps switching capacity Hardened IP30 rated metal housing Includes DIN-rail mounting bracket Wide operating temperature range of -40° – 75° C (-40° – 167° F) Supports LACP, STP/RSTP, VLAN, and IGMP Snooping IEEE 802.1p QoS with queue scheduling support Bandwidth control per port Redundant power inputs with overload current protection Alarm output triggered by power failure Supports Ethernet Ring Protection Switching (ERPSv2) Power supply sold separately (model: TI-M6024) TRENDnet’s Industrial Gigabit L2 Managed DIN-Rail Switch series offers advanced layer 2 managed features with enhanced traffic controls to meet the evolving demands of today’s SMB networks. Each industrial layer 2 managed switch is equipped with an IP30 rated metal enclosure, designed to withstand a high degree of vibration and shock, while operating within a wide temperature range of -40° – 75° C (-40° – 167° F) for industrial environments. Our industrial layer 2 managed switch models feature copper Gigabit ports for high-speed device connections, and SFP slots that support both 100Base-FX and 1000Base-FX modules for long distance fiber networking applications. These industrial layer 2 managed DIN-Rail switches provide an intuitive web-based management interface. Each TRENDnet industrial layer 2 managed switch supports advanced traffic management controls, troubleshooting, and SNMP monitoring. Advanced managed switch features include LACP to group ports together to increase bandwidth between switches, VLANs for segmenting and isolating virtual LAN groups, QoS for traffic prioritization, port bandwidth controls, and SNMP monitoring making each TRENDnet industrial layer 2 managed switch a powerful solution for SMB networks. Integration Flexibility Managed layer 2 features include VLAN, IGMP snooping, QoS, RMON, SNMP trap, and syslog for monitoring and flexible network integration. Shock and Vibration Resistant The industrial layer 2 managed switches are rated for shock (EN 60068-2-27), freefall (EN 60068-2-32), and vibration (EN 60068-2-6). Industrial Design Equipped with an IP30 rated metal enclosure, the industrial layer 2 managed switch operates within a wide temperature range of -40° – 75° C (-40° – 167° F). Network Ports Gigabit ports for high-speed network connectivity and SFP slots for long distance fiber applications Traffic Management Layer 2 Managed features include 802.1Q, MAC & Port Isolation VLAN, IGMP Snooping, per port bandwidth control / 802.1p / DSCP / Queue Scheduling (SPQ / WRR), STP / RSTP spanning tree, and link aggregation for flexible network integration Access Control Managed access control features include ACLs, IP-MAC-Port binding, ARP inspection, 802.1X RADIUS, MAC address learning, DHCP snooping, and IP Source Guard provide the industrial layer 2 managed switches with layered network access controls System Monitoring Monitoring features include SNMP v1 / v2c / v3, MIB support, SNMP trap, RMON Groups (1, 2, 3, 9), SMTP alert, syslog, port mirroring, and SFP DDMI DIN-Rail Mount IP30 rated metal enclosure, includes DIN-rail mounting bracket for the industrial layer 2 managed switch Redundant Power Redundant power inputs with overload current protection (power supply sold separately) Alarm Relay Alarm relay output triggered by power failure of primary and / or redundant power to the industrial layer 2 managed switch Jumbo Frame Sends larger packets, or Jumbo Frames (up to 10KB), for increased performance from the industrial layer 2 managed switch Wide Temperature Range A wide operating temperature range of -40° – 75° C (-40° – 167° F) allows for installations in industrial environments with extreme hot or cold conditions Shock and Vibration Resistant Rated for shock (EN 60068-2-27), freefall (EN 60068-2-32), and vibration (EN 60068-2-6) Grounding Point Grounding point protects equipment from external electrical surges on the industrial layer 2 managed switch
LTU-PRO Incorporating innovative industrial design with advanced technology, the LTU Pro is a Point-to-MultiPoint (PtMP) 5 GHz high-performance subscriber station. Based on Ubiquiti’s proprietary LTU technology, the LTU Pro is not impeded by the limitations of standard 802.11 Wi-Fi technology. It features an integrated high-gain dish for long range and high performance. Channel width flexibility (10/20/30/40/50 MHz) allows independent TX and RX channel frequency configurations anywhere within the radio band to avoid local interference. Features: PtMP CPE 1024 QAM 10/20/30/40/50 MHz channel bandwidth Central configuration management from AP side Frequency split Automatic power adjustments Router mode support Functions in a PtMP environment with the LTU-Rocket as the basestation. Featuring an integrated 24 dBi dish antenna, the LTU Pro is a 5 GHz subscriber station that functions as a CPE (Customer Premises Equipment) in a Point‑to‑MultiPoint (PtMP) environment with the LTU Rocket® as the basestation.Proprietary LTU Technology Based on Ubiquiti’s LTU technology, the LTU Pro is not impeded by the limitations of standard 802.11 Wi‑Fi technology. Its custom LTU silicon and radio architecture provide up to 600+ Mbps (1) of real TCP/IP throughput and modulation rates of up to 4096QAM (2). 1 1+ Gbps with future firmware upgrade.2 Available with future firmware upgrade. CPE Modes The LTU Pro supports both bridged and built-in hardware NAT router modes to suit your specific deployment. Frequency Split The LTU Pro can use different frequencies for TX and RX to avoid interference. Robust Pole Mount Design The LTU Pro is designed for quick yet reliable mounting on a pole. It features a built-in mechanical tilt; the mounting bracket allows convenient adjustments to the elevation with a range of ± 15°.
Deploy the UniFi XG AP in very high-density environments requiring maximum wireless performance. The UniFi XG AP features simultaneous dual-band 4x4 MU-MIMO technology and convenient 802.3bt PoE compatibility.10G and 1G Ethernet Connectivity Designed to be a 10G Ethernet backhaul the primary port carries both data and PoE while the secondary Gigabit Ethernet port is for bridging and also supports PoE input.Features: 10 Gigabit Ethernet Support4x4 MU-MIMO Quad-Radio: (3) client 1 SecurityDual 5 GHz 802.11ac Wave 2 Radios3.466 Gbps Combined Radio Rate in 5 GHz800 Mbps Radio Rate in 2.4 GHzDedicated Security Radio with Persistent Threat Management1 500 Client Association Limit
CAT6 UTP Patch CableVention CAT6 Patch Cord is used in network applications such as 10Base-T 100Base-T 1000Base-T Ethernet and have been designed specifically for Gigabit Ethernet applications (Gigabit over copper). They perform at high-data transfer rates. These cables deliver improved performance over standard CAT5E cables.CAT6 is completely backward-compatible with current CAT5 CAT5E equipment. Vention CAT6 Patch Cords are composed of 4 pairs 26AWG stranded conductors with PVC jackets. Conductors are wired to gold plated RJ45 plugs in accordance with the TIA/EIA 568B standard.Used to connect your network card to any of the following: 10GBASE-T Ethernet 1000BASE-T Gigabit Ethernet 100BASE-T Ethernet 100BASE-TX Fast Ethernet 10BASE-T Ethernet Patch cords have stranded copper conductors for flexibility - great for frequent changes that occur at the wall outlet or patch panel.Virtually eliminates alien crosstalk and interference.Performance rated beyond 250 MHz.
CAT6 UTP Patch CableVention CAT6 Patch Cord is used in network applications such as 10Base-T 100Base-T 1000Base-T Ethernet and have been designed specifically for Gigabit Ethernet applications (Gigabit over copper). They perform at high-data transfer rates. These cables deliver improved performance over standard CAT5E cables.CAT6 is completely backward-compatible with current CAT5 CAT5E equipment. Vention CAT6 Patch Cords are composed of 4 pairs 26AWG stranded conductors with PVC jackets. Conductors are wired to gold plated RJ45 plugs in accordance with the TIA/EIA 568B standard.Used to connect your network card to any of the following: 10GBASE-T Ethernet 1000BASE-T Gigabit Ethernet 100BASE-T Ethernet 100BASE-TX Fast Ethernet 10BASE-T Ethernet Patch cords have stranded copper conductors for flexibility - great for frequent changes that occur at the wall outlet or patch panel.Virtually eliminates alien crosstalk and interference.Performance rated beyond 250 MHz.
CAT6a UTP Slim Patch CableAugmented Category 6 or CAT6a Cable is used in network applications such as 10Base-T 100Base-T 1000Base-T 10000Base-T Ethernet up to 100 meters. CAT6a cables have been designed specifically for 10 Gigabit Ethernet applications over copper. They perform at high-data transfer rates and operate at a minimum frequency of 500 MHz. These cables deliver improved performance over standard CAT6 cables.CAT6a is completely backward-compatible with current CAT6 CAT5E and CAT5 equipment. Vention CAT6a Flat Cables are composed of 4 twisted pair 32 AWG stranded copper conductors with PVC jackets. Conductors are wired to gold plated RJ45 plugs in accordance with the draft specification ANSI/TIA/EIA-568-B.2-10 standard.Use to connect your network card to any of the following: 10GBASE-T Ethernet 1000BASE-TX Fast Ethernet 1000BASE-T Gigabit Ethernet 100BASE-TX Fast Ethernet 10BASE-T Ethernet Patch cables have stranded copper conductors for flexibility - great for frequent changes that occur at the wall outlet or patch panel.Suppresses ANEXT (Alien Near End Cross Talk) and delivers superior 10 GbE performance up to 100 meters.Performance rated beyond 500 MHz.
With the UniFi In-Wall HD Cover the In-Wall HD AP blends seamlessly into a variety of backgrounds. Available in five different designs and sold as a 3-Pack. * - UniFi In-Wall HD AP sold separately!
* Võimaldab kahel arvutil jagada kuni 4 seadet(hiir, klaviatuur, USB pulk, skänner, printer jne) * 2x USB 3.0 sisse/ 4x USB 3.0 välja * kuni 5Gbps Data * Võimalik lisatoide läbi micro USB pesa * Mõõdud 105x53x16mm
Mercusys AC1300 Whole Home Mesh Wi-Fi System Halo H30G (2-Pack) 802.11ac, 400+867 Mbit/s, Ethernet LAN (RJ-45) ports 2, Mesh Support Yes, MU-MiMO Yes, White
