Arvutitark OÜ

Alphacool Eisplateau Anti-Static matA clean workplace is a precondition for a successful work and a good result. The Alphacool Eisplateau provides the basis therefor and all the important dimensions and datas are always at hand. The Eisplateau is made of an insulating rubber mat with fine, cleanly printed textile. So the mat is also eminently suitable as a mousepad without limits. In addition, the ice plateau has two antistatic clips to connect an alligator clip and an anti-static wrist strap. By usind a corresponding subsurface static charges are derived directly without damaging it standing Hardware. Technical Details: Dimensions: 1200 x 600 x 4mm Material: rubber, printed textile Scope of delivery: 1x Eisplateau 1x cable with an anti-static wrist strap 1x cable with an alligator clip

The Alphacool VPP Apex pump including the Eisdecke D5 Acetal V.3 combines powerful PWM-controlled pump technology with a versatile pump top. Three inlets, two outlets, and a stable mounting base allow for flexible integration into any custom loop system.With the Eisdecke D5 Acetal V.3, the Apex VPP pump receives a housing that impresses both functionally and visually. The Eisdecke offers maximum flexibility in tube routing with a total of three inlets and two outlets. The new bracket ensures a stable stand and also allows installation in a 3.5" drive bay.The Apex VPP is based on the well-known D5 format but has been significantly improved in key areas. Instead of a spherical bearing, it uses a ceramic shaft, which increases smooth operation and significantly reduces vibrations. Thanks to the redesigned coil layout, power consumption has been nearly halved.Power is supplied via a modern SATA connector. The 4-pin PWM connector allows precise control and monitoring of the pump’s speed – ideal for users who demand full control over their system.Optionally, the pump unit can be expanded into a complete pump/reservoir combo by adding a separately available reservoir top – perfect for compact and high-performance water cooling setups. Technical data: Apex VPP PumpDimensions (L x W x H)65 x 65 x 41mmMaterial pumpsynthetic materialMaterial pump coveraluminiumMaterial axleceramicsConnections4-Pin PWM | SATARotational speed2500 - 4500 RPMCable lengths4-Pin PWM - 48cm | SATA - 48cmOperating voltage8-13V DC / 14W IP32Starting voltage12V DCMaximum pumping head4,25mMaximum flow rate340L/hMaximum working temperature60°CWeight276gColorblackTechnical data: Eisdecke D5 - Acetal V.3Dimensions (L x W x H)80 x 80 x 40mmDimensions (L x W x H) with stand83 x 80 x 87mmMaterialAcetalThreads5x 1/4"Warranty: 5 years???? Warranty Terms

The HardTube Project is becoming a reality. Alphacool is setting out on a new path and making great strides! Before now, the most common approach to water cooling was to use normal PVC tubes – now Alphacool is offering a new way to configure your water cooling system. The HardTube variants bring more order into your system, which gives off a more structured impression. The newest are the brass tubes, available in black chrome and chrome, as well as acrylic tubes, carbon, and borosilicate glass. With their fitted connectors and simply-designed functionality, they can be connected to each other with an absolutely tight seal. The PETG-tubes can be bent with the appropriate bending tools in order to fit into any system easily, without needing any additional angled pieces. In order to install the tubes into the system, they need to be sawn to the correct length. PETG tubes can be bent at lower temperatures than acrylic and are generally more flexible and easier to handle. Technical Details: Material: PETG Length: 80cm Scope of delivery: 1x Alphacool Eisrohr 13/10mm PETG 80cm - 4pcs

The HardTube Project is becoming a reality. Alphacool is setting out on a new path and making great strides! Before now, the most common approach to water cooling was to use normal PVC tubes – now Alphacool is offering a new way to configure your water cooling system. The HardTube variants bring more order into your system, which gives off a more structured impression. The newest are the brass tubes, available in black chrome and chrome, as well as acrylic tubes, carbon, and borosilicate glass. With their fitted connectors and simply-designed functionality, they can be connected to each other with an absolutely tight seal. The PETG-tubes can be bent with the appropriate bending tools in order to fit into any system easily, without needing any additional angled pieces. In order to install the tubes into the system, they need to be sawn to the correct length. PETG tubes can be bent at lower temperatures than acrylic and are generally more flexible and easier to handle. Technical Details: Material: PETG Length: 60cm Scope of delivery: 1x Alphacool Eisrohr 13/10mm PETG 60cm - 4pcs

The Alphacool Eisrohr PETG HardTube givse the user the possibility to create a very special look. With a wall thickness of 3 mm, the tubes are very strong, but can still be bent without great effort and they are easy to fit. PETG HardTubes are probably the easiest to bend compared to those made of other materials. They require significantly less heat than PMMA HardTubes, for example. The Alphacool Eisrohr PETG HardTubes are absolutely clear and will look great in almost every water cooling loop. When cutting the tubes, make sure to chamfer the edges with fine file , sandpaper or the Alphacool Strong Guy pipe and hose deburrer, as sharp edges can damage the O-rings of fittings.Technical data:Outer diameter: 14 mmInner diameter: 11 mmLength: 80 cmMaterial: PETG clearNet weight: 58 g Download data sheet PDF: Alphacool Eisrohr 14/11mm PETG HardTube 80cm - 4pcs

The HardTube Project is becoming a reality. Alphacool is setting out on a new path and making great strides! Before now, the most common approach to water cooling was to use normal PVC tubes – now Alphacool is offering a new way to configure your water cooling system. The HardTube variants bring more order into your system, which gives off a more structured impression. The newest are the brass tubes, available in black chrome and chrome, as well as acrylic tubes, carbon, and borosilicate glass. With their fitted connectors and simply-designed functionality, they can be connected to each other with an absolutely tight seal. The PETG-tubes can be bent with the appropriate bending tools in order to fit into any system easily, without needing any additional angled pieces. In order to install the tubes into the system, they need to be sawn to the correct length. PETG tubes can be bent at lower temperatures than acrylic and are generally more flexible and easier to handle. Technical Details: Material: PETG Length: 60cm Scope of delivery: 1x Alphacool Eisrohr 16/13mm PETG 60cm - 4pcs

The HardTube Project is becoming a reality. Alphacool is setting out on a new path and making great strides! Before now, the most common approach to water cooling was to use normal PVC tubes – now Alphacool is offering a new way to configure your water cooling system. The HardTube variants bring more order into your system, which gives off a more structured impression. The newest are the brass tubes, available in black chrome and chrome, as well as acrylic tubes, carbon, and borosilicate glass. With their fitted connectors and simply-designed functionality, they can be connected to each other with an absolutely tight seal. The PETG-tubes can be bent with the appropriate bending tools in order to fit into any system easily, without needing any additional angled pieces. In order to install the tubes into the system, they need to be sawn to the correct length. PETG tubes can be bent at lower temperatures than acrylic and are generally more flexible and easier to handle. Technical Details: Material: PETG Length: 80cm Scope of delivery: 1x Alphacool Eisrohr 16/13mm PETG 80cm - 4pcs

Alphacool's ultimate solution lets you cool your computer with a sheet of ice. Not an ice sheet in the conventional sense, made of frozen water, but a sheet that brings every chip down to freezing. The properties of these new thermal pads speak for themselves.The light version of the Alphacool Eisschicht ("ice sheet") is the "small and weak" version at 7W/mK, but is definitely strong enough. Any hardware components can now be put together neatly and easily with thermal pads. The Alphacool Eisschicht offers all the benefits and typical qualities of a thermal pad: self-adhesive, elastic, flexible, and much more! Just as varied are the options for placement: whether on RAM or motherboard coolers, or graphics card and CPU coolers, any place where chips meet cooler bodies is a good place for an Alphacool Eisschicht.The Eisschicht Light, with a performance level of 7W/mK, is available in 0.5mm, 1mm, and 1.5mm thicknesses. Perfect for levelling height differences. Each thickness is also available in 100x100mm and 120x20mm (suitable for RAM coolers) sizes. These can easily be cut with scissors to get the right size for any component. Technical dataDimensions (L x W x H)100 x 100 x 0,5mmThermal conductivity7W/mKColorpink

Alphacool's ultimate solution lets you cool your computer with a sheet of ice. Not an ice sheet in the conventional sense, made of frozen water, but a sheet that brings every chip down to freezing. The properties of these new thermal pads speak for themselves.The light version of the Alphacool Eisschicht ("ice sheet") is the "small and weak" version at 7W/mK, but is definitely strong enough. Any hardware components can now be put together neatly and easily with thermal pads. The Alphacool Eisschicht offers all the benefits and typical qualities of a thermal pad: self-adhesive, elastic, flexible, and much more! Just as varied are the options for placement: whether on RAM or motherboard coolers, or graphics card and CPU coolers, any place where chips meet cooler bodies is a good place for an Alphacool Eisschicht.The Eisschicht Light, with a performance level of 7W/mK, is available in 0.5mm, 1mm, and 1.5mm thicknesses. Perfect for levelling height differences. Each thickness is also available in 100x100mm and 120x20mm (suitable for RAM coolers) sizes. These can easily be cut with scissors to get the right size for any component. Technical dataDimensions (L x W x H)100 x 100 x 1,5mmThermal conductivity7W/mKColorpink

Alphacool's ultimate solution lets you cool your computer with a sheet of ice. Not an ice sheet in the conventional sense, made of frozen water, but a sheet that brings every chip down to freezing. The properties of these new thermal pads speak for themselves.The light version of the Alphacool Eisschicht ("ice sheet") is the "small and weak" version at 7W/mK, but is definitely strong enough. Any hardware components can now be put together neatly and easily with thermal pads. The Alphacool Eisschicht offers all the benefits and typical qualities of a thermal pad: self-adhesive, elastic, flexible, and much more! Just as varied are the options for placement: whether on RAM or motherboard coolers, or graphics card and CPU coolers, any place where chips meet cooler bodies is a good place for an Alphacool Eisschicht.The Eisschicht Light, with a performance level of 7W/mK, is available in 0.5mm, 1mm, and 1.5mm thicknesses. Perfect for levelling height differences. Each thickness is also available in 100x100mm and 120x20mm (suitable for RAM coolers) sizes. These can easily be cut with scissors to get the right size for any component. Technical dataDimensions (L x W x H)100 x 100 x 1mmThermal conductivity7W/mKColorpink

Alphacool's ultimate solution lets you cool your computer with a sheet of ice. Not an ice sheet in the conventional sense, made of frozen water, but a sheet that brings every chip down to freezing. The properties of these new thermal pads speak for themselves.The light version of the Alphacool Eisschicht ("ice sheet") is the "small and weak" version at 7W/mK, but is definitely strong enough. Any hardware components can now be put together neatly and easily with thermal pads. The Alphacool Eisschicht offers all the benefits and typical qualities of a thermal pad: self-adhesive, elastic, flexible, and much more! Just as varied are the options for placement: whether on RAM or motherboard coolers, or graphics card and CPU coolers, any place where chips meet cooler bodies is a good place for an Alphacool Eisschicht.The Eisschicht Light, with a performance level of 7W/mK, is available in 0.5mm, 1mm, and 1.5mm thicknesses. Perfect for levelling height differences. Each thickness is also available in 100x100mm and 120x20mm (suitable for RAM coolers) sizes. These can easily be cut with scissors to get the right size for any component. Technical dataDimensions (L x W x H)120 x 20 x 0,5mmThermal conductivity7W/mKColorpink

Alphacool's ultimate solution for cooling your computer with a layer of ice. Not a layer of ice in the traditional sense made of frozen water, but a layer that will freeze any chip. The properties of the new thermal pads speak for themselves.The "Alphacool ice layer" offers all the advantages and typical properties of a thermal pad: self-adhesive, elastic, adaptable and much more! The area of application is just as versatile, whether for RAM and mainboard coolers or graphics card and CPU coolers, wherever the circuit board meets the heat sink, the Alphacool ice layer is a good choice.The Ice Layers Light are available in the 7W/mk power level in 0.5mm, 1mm and 1.5mm thicknesses. Perfect for compensating for height differences. Each thickness is also available in 100x100mm and 120x20mm (suitable for RAM coolers). These can be easily separated with scissors to individually adjust the right size for each component Technical dataDimensions (L x W x H)14 x 14 x 1mmThermal conductivity7W/mKColorpink

Alphacool's ultimate solution lets you cool your computer with a sheet of ice. Not an ice sheet in the conventional sense, made of frozen water, but a sheet that brings every chip down to freezing. The properties of these new thermal pads speak for themselves. The light version of the Alphacool Eisschicht ("ice sheet") is the "small and weak" version at 7W/mK, but is definitely strong enough. Any hardware components can now be put together neatly and easily with thermal pads. The Alphacool Eisschicht offers all the benefits and typical qualities of a thermal pad: self-adhesive, elastic, flexible, and much more! Just as varied are the options for placement: whether on RAM or motherboard coolers, or graphics card and CPU coolers, any place where chips meet cooler bodies is a good place for an Alphacool Eisschicht. The Eisschicht Light, with a performance level of 7W/mK, is available in 0.5mm, 1mm, and 1.5mm thicknesses. Perfect for leveling height differences. Each thickness is also available in 100x100mm and 120x20mm (suitable for RAM coolers) sizes. These can easily be cut with scissors to get the right size for any component.

Alphacool's ultimate solution lets you cool your computer with a sheet of ice. Not an ice sheet in the conventional sense, made of frozen water, but a sheet that brings every chip down to freezing. The properties of these new thermal pads speak for themselves.The light version of the Alphacool Eisschicht ("ice sheet") is the "small and weak" version at 7W/mK, but is definitely strong enough. Any hardware components can now be put together neatly and easily with thermal pads. The Alphacool Eisschicht offers all the benefits and typical qualities of a thermal pad: self-adhesive, elastic, flexible, and much more! Just as varied are the options for placement: whether on RAM or motherboard coolers, or graphics card and CPU coolers, any place where chips meet cooler bodies is a good place for an Alphacool Eisschicht.The Eisschicht Light, with a performance level of 7W/mK, is available in 0.5mm, 1mm, and 1.5mm thicknesses. Perfect for levelling height differences. Each thickness is also available in 100x100mm and 120x20mm (suitable for RAM coolers) sizes. These can easily be cut with scissors to get the right size for any component. Technical dataDimensions (L x W x H)120 x 20 x 1mmThermal conductivity7W/mKColorpink

Alphacool’s ultimate solution to cool your computer with a layer of ice. Not frozen water but a sensational new thermal pad: With up to 17 W / mk pads surpass all previously-seen thermal pads and pastes. So now practically all hardware components can be easily and cleanly covered with ice! The "Alphacool Eisschicht" offers all the benefits and features of a typical thermal pads: self-adhesive, elastic, adaptable, and more! It canbe used in many applications: RAM and motherboard coolers or graphics cards and CPU coolers, wherever board meets heatsink you are well advised with the Alphacool Eisschicht. The pads are available in different power levels, 11, 14 and 17W / mk each available in 0.5mm, 1mm and 1.5mm thickness to be able to compensate for differences in height perfectly. Likewise, any thickness is again available in 100x100mm and 120x20mm (suitable for RAM cooler). These can be easily cut with scissors to separate the right size for each component to be individually configured.

Alphacool’s ultimate solution to cool your computer with a layer of ice. Not frozen water but a sensational new thermal pad: With up to 17 W / mk pads surpass all previously-seen thermal pads and pastes. So now practically all hardware components can be easily and cleanly covered with ice! The "Alphacool Eisschicht" offers all the benefits and features of a typical thermal pads: self-adhesive, elastic, adaptable, and more! It canbe used in many applications: RAM and motherboard coolers or graphics cards and CPU coolers, wherever board meets heatsink you are well advised with the Alphacool Eisschicht. The pads are available in different power levels, 11, 14 and 17W / mk each available in 0.5mm, 1mm and 1.5mm thickness to be able to compensate for differences in height perfectly. Likewise, any thickness is again available in 100x100mm and 120x20mm (suitable for RAM cooler). These can be easily cut with scissors to separate the right size for each component to be individually configured.

Alphacool’s ultimate solution to cool your computer with a layer of ice. Not frozen water but a sensational new thermal pad: With up to 17 W / mk pads surpass all previously-seen thermal pads and pastes. So now practically all hardware components can be easily and cleanly covered with ice! The "Alphacool Eisschicht" offers all the benefits and features of a typical thermal pads: self-adhesive, elastic, adaptable, and more! It canbe used in many applications: RAM and motherboard coolers or graphics cards and CPU coolers, wherever board meets heatsink you are well advised with the Alphacool Eisschicht. The pads are available in different power levels, 11, 14 and 17W / mk each available in 0.5mm, 1mm and 1.5mm thickness to be able to compensate for differences in height perfectly. Likewise, any thickness is again available in 100x100mm and 120x20mm (suitable for RAM cooler). These can be easily cut with scissors to separate the right size for each component to be individually configured.

Alphacool’s ultimate solution to cool your computer with a layer of ice. Not frozen water but a sensational new thermal pad: With up to 17 W / mk pads surpass all previously-seen thermal pads and pastes. So now practically all hardware components can be easily and cleanly covered with ice! The "Alphacool Eisschicht" offers all the benefits and features of a typical thermal pads: self-adhesive, elastic, adaptable, and more! It canbe used in many applications: RAM and motherboard coolers or graphics cards and CPU coolers, wherever board meets heatsink you are well advised with the Alphacool Eisschicht. The pads are available in different power levels, 11, 14 and 17W / mk each available in 0.5mm, 1mm and 1.5mm thickness to be able to compensate for differences in height perfectly. Likewise, any thickness is again available in 100x100mm and 120x20mm (suitable for RAM cooler). These can be easily cut with scissors to separate the right size for each component to be individually configured.

Alphacool’s ultimate solution to cool your computer with a layer of ice. Not frozen water but a sensational new thermal pad: With up to 17 W / mk pads surpass all previously-seen thermal pads and pastes. So now practically all hardware components can be easily and cleanly covered with ice! The "Alphacool Eisschicht" offers all the benefits and features of a typical thermal pads: self-adhesive, elastic, adaptable, and more! It canbe used in many applications: RAM and motherboard coolers or graphics cards and CPU coolers, wherever board meets heatsink you are well advised with the Alphacool Eisschicht. The pads are available in different power levels, 11, 14 and 17W / mk each available in 0.5mm, 1mm and 1.5mm thickness to be able to compensate for differences in height perfectly. Likewise, any thickness is again available in 100x100mm and 120x20mm (suitable for RAM cooler). These can be easily cut with scissors to separate the right size for each component to be individually configured.

Alphacool’s ultimate solution to cool your computer with a layer of ice. Not frozen water but a sensational new thermal pad: With up to 17 W / mk pads surpass all previously-seen thermal pads and pastes. So now practically all hardware components can be easily and cleanly covered with ice! The "Alphacool Eisschicht" offers all the benefits and features of a typical thermal pads: self-adhesive, elastic, adaptable, and more! It canbe used in many applications: RAM and motherboard coolers or graphics cards and CPU coolers, wherever board meets heatsink you are well advised with the Alphacool Eisschicht. The pads are available in different power levels, 11, 14 and 17W / mk each available in 0.5mm, 1mm and 1.5mm thickness to be able to compensate for differences in height perfectly. Likewise, any thickness is again available in 100x100mm and 120x20mm (suitable for RAM cooler). These can be easily cut with scissors to separate the right size for each component to be individually configured.

Alphacool’s ultimate solution to cool your computer with a layer of ice. Not frozen water but a sensational new thermal pad: With up to 17 W / mk pads surpass all previously-seen thermal pads and pastes. So now practically all hardware components can be easily and cleanly covered with ice! The "Alphacool Eisschicht" offers all the benefits and features of a typical thermal pads: self-adhesive, elastic, adaptable, and more! It canbe used in many applications: RAM and motherboard coolers or graphics cards and CPU coolers, wherever board meets heatsink you are well advised with the Alphacool Eisschicht. The pads are available in different power levels, 11, 14 and 17W / mk each available in 0.5mm, 1mm and 1.5mm thickness to be able to compensate for differences in height perfectly. Likewise, any thickness is again available in 100x100mm and 120x20mm (suitable for RAM cooler). These can be easily cut with scissors to separate the right size for each component to be individually configured.

Alphacool’s ultimate solution to cool your computer with a layer of ice. Not frozen water but a sensational new thermal pad: With up to 17 W / mk pads surpass all previously-seen thermal pads and pastes. So now practically all hardware components can be easily and cleanly covered with ice! The "Alphacool Eisschicht" offers all the benefits and features of a typical thermal pads: self-adhesive, elastic, adaptable, and more! It canbe used in many applications: RAM and motherboard coolers or graphics cards and CPU coolers, wherever board meets heatsink you are well advised with the Alphacool Eisschicht. The pads are available in different power levels, 11, 14 and 17W / mk each available in 0.5mm, 1mm and 1.5mm thickness to be able to compensate for differences in height perfectly. Likewise, any thickness is again available in 100x100mm and 120x20mm (suitable for RAM cooler). These can be easily cut with scissors to separate the right size for each component to be individually configured.

Alphacool's ultimate solution for cooling your computer with a layer of ice. Not a layer of ice in the traditional sense made of frozen water, but a layer that will freeze any chip. The properties of the new thermal pads speak for themselves.With up to 17 W/mk, the pads outperform all previous thermal pads and pastes! All hardware components can now be installed easily and cleanly using thermal pads!The "Alphacool ice layer" offers all the advantages and typical properties of a thermal pad: self-adhesive, elastic, adaptable and much more! The area of application is just as versatile, whether for RAM and mainboard coolers or graphics card and CPU coolers, wherever the circuit board meets the heat sink, the Alphacool ice layer is a good choice.The pads are available in different power levels, 11, 14 and 17W/mk, each available in 0.5mm, 1mm and 1.5mm thickness to perfectly compensate for height differences. Each thickness is also available in 100x100mm and 120x20mm (suitable for RAM coolers). These can be easily separated with scissors to individually adjust the right size for each component. Technical dataDimensions (L x W x H)100 x 100 x 0,5mmThermal conductivity17W/mKThickness0,5mmFlame retardantV-0 (UL94)Useful temperature-40 ~ +150 °CHardness72 (Shore OO)Specific gravity3.2Breakdown voltage10 kV/mmElongation40 %Tensile strength0.5 MPaVolume resistivity1.0x10^11 Ohm-mFasteningslightly adhesiveColorgrey

Alphacool's ultimate solution for cooling your computer with a layer of ice. Not a layer of ice in the traditional sense made of frozen water, but a layer that will freeze any chip. The properties of the new thermal pads speak for themselves.With up to 17 W/mk, the pads outperform all previous thermal pads and pastes! All hardware components can now be installed easily and cleanly using thermal pads!The "Alphacool ice layer" offers all the advantages and typical properties of a thermal pad: self-adhesive, elastic, adaptable and much more! The area of application is just as versatile, whether for RAM and mainboard coolers or graphics card and CPU coolers, wherever the circuit board meets the heat sink, the Alphacool ice layer is a good choice.The pads are available in different power levels, 11, 14 and 17W/mk, each available in 0.5mm, 1mm and 1.5mm thickness to perfectly compensate for height differences. Each thickness is also available in 100x100mm and 120x20mm (suitable for RAM coolers). These can be easily separated with scissors to individually adjust the right size for each component. Technical dataDimensions (L x W x H)100 x 100 x 1,5mmThermal conductivity17W/mKThickness1,5mmFlame retardantV-0 (UL94)Useful temperature-40 ~ +150 °CHardness72 (Shore OO)Specific gravity3.2Breakdown voltage10 kV/mmElongation40 %Tensile strength0.5 MPaVolume resistivity1.0x10^11 Ohm-mFasteningslightly adhesiveColorgrey

Alphacool’s ultimate solution to cool your computer with a layer of ice. Not frozen water but a sensational new thermal pad: With up to 17 W / mk pads surpass all previously-seen thermal pads and pastes. So now practically all hardware components can be easily and cleanly covered with ice! The "Alphacool Eisschicht" offers all the benefits and features of a typical thermal pads: self-adhesive, elastic, adaptable, and more! It canbe used in many applications: RAM and motherboard coolers or graphics cards and CPU coolers, wherever board meets heatsink you are well advised with the Alphacool Eisschicht. The pads are available in different power levels, 11, 14 and 17W / mk each available in 0.5mm, 1mm and 1.5mm thickness to be able to compensate for differences in height perfectly. Likewise, any thickness is again available in 100x100mm and 120x20mm (suitable for RAM cooler). These can be easily cut with scissors to separate the right size for each component to be individually configured.

Alphacool’s ultimate solution to cool your computer with a layer of ice. Not frozen water but a sensational new thermal pad: With up to 17 W / mk pads surpass all previously-seen thermal pads and pastes. So now practically all hardware components can be easily and cleanly covered with ice! The "Alphacool Eisschicht" offers all the benefits and features of a typical thermal pads: self-adhesive, elastic, adaptable, and more! It canbe used in many applications: RAM and motherboard coolers or graphics cards and CPU coolers, wherever board meets heatsink you are well advised with the Alphacool Eisschicht. The pads are available in different power levels, 11, 14 and 17W / mk each available in 0.5mm, 1mm and 1.5mm thickness to be able to compensate for differences in height perfectly. Likewise, any thickness is again available in 100x100mm and 120x20mm (suitable for RAM cooler). These can be easily cut with scissors to separate the right size for each component to be individually configured.

Alphacool’s ultimate solution to cool your computer with a layer of ice. Not frozen water but a sensational new thermal pad: With up to 17 W / mk pads surpass all previously-seen thermal pads and pastes. So now practically all hardware components can be easily and cleanly covered with ice! The "Alphacool Eisschicht" offers all the benefits and features of a typical thermal pads: self-adhesive, elastic, adaptable, and more! It canbe used in many applications: RAM and motherboard coolers or graphics cards and CPU coolers, wherever board meets heatsink you are well advised with the Alphacool Eisschicht. The pads are available in different power levels, 11, 14 and 17W / mk each available in 0.5mm, 1mm and 1.5mm thickness to be able to compensate for differences in height perfectly. Likewise, any thickness is again available in 100x100mm and 120x20mm (suitable for RAM cooler). These can be easily cut with scissors to separate the right size for each component to be individually configured.

The Eisschicht from Alphacool can, like other thermal pads, compensate for the irregularities of heat sinks and the elements to be cooled. But it has a great feature: The Eisschicht consists of thermal paste with an embedded mesh! This ensures that the performance of these pads is much more efficient than normal thermal pads, regardless of the low W/mK value. In addition, a better distribution and filling between the surfaces is achieved. This also results in better air displacement. Due to their soft consistency, there is also no pressure on components or solder joints. Nvidia also uses this kind of pads for the Founders Edition. The Eisschicht can be easily cut to the desired size and attached to heat sinks without slipping.As a basic component or spare part, thermal pads belong in every well-organized computer tinkering corner! Technical dataDimensions (L x W x H)100 x 100 x 0,5mmThermal conductivity3 W/mKElectrical ConductiveNoColorwhite

The Eisschicht Ultra Soft are Alphacool's performance oriented solution in the range of thermal pads. Due to their outstanding properties, they can almost be compared to a thermal paste. These Ultra Soft thermal pads nestle much better to components, which contributes to a significant improvement in cooling performance.Better than standard thermal pads?The material of the Ultra Soft thermal pads acts similar to a thermal paste. While normal thermal pads are only pressed together by the contact pressure there can be areas that are uneven due to different high components, making them less effective. With the ultra soft Eisschicht this problem doesn’t exist because the material distributes itself similar to thermal paste and thus prevents the highest components from being subjected to increased contact pressure by the cooler. As standard thermal pads are quite stiff they can also cause too much pressure on components. In the worst cases, this can cause the PCB to bend and even break. Due to the soft consistency of the Ultra Soft Eisschicht any excess material can spread out rather than cause problems. The Ultra Soft Eisschicht is not only performance orientated, but also safer!But this is not the only advantage!Moreover, the special material cannot dry out. Usually the silicone in thermal pads bleeds out over time. This makes them hard and the performance of the pads drops rapidly from a certain point. This is not the case with the Ultra Soft Eisschicht. They can be used over a much longer period of time without significantly losing performance.A thermal pad with fabric?The consistency of the heat conducting material is similar to a viscous heat conducting paste. A special fabric is embedded so that the material remains stable and can be used as a thermal pad. This ensures a perfect distribution of the material if the element to be cooled has an uneven shape. Examples include voltage transformers, VRam and similar electronic components of all kinds that require cooling.Cutting? No problem!To cut the thermal pads to size, you should definitely leave the foil on the pads. So the pads can easily be cut to size with a pair of scissors. This is just as easy as cutting paper. The cut edges remain perfectly clean and do not fray. Technical dataL x W x H100 x 100 x 1,5mmSpecific Gravitiy ASTM D2972,65 g/ccThermal Conductivity ASTM D54703.0 W/mKHardness ASTM 224020 Shore 00Working temperature40 to 200°COutgassing ASTM E5950,40% TMLVolume Resistivity ASTM D2576.2X10 high 13 Ohm-meterDielectric Constant ASTM D1505,5 MHzDielectric Breakdown Voltage ASTM D149>5000 VACFlame Rating UL E33110094 V0Colorwhite

The Eisschicht from Alphacool can, like other thermal pads, compensate for the irregularities of heat sinks and the elements to be cooled. But it has a great feature: The Eisschicht consists of thermal paste with an embedded mesh! This ensures that the performance of these pads is much more efficient than normal thermal pads, regardless of the low W/mK value. In addition, a better distribution and filling between the surfaces is achieved. This also results in better air displacement. Due to their soft consistency, there is also no pressure on components or solder joints. Nvidia also uses this kind of pads for the Founders Edition. The Eisschicht can be easily cut to the desired size and attached to heat sinks without slipping.As a basic component or spare part, thermal pads belong in every well-organized computer tinkering corner! Technical dataDimensions (L x W x H)100 x 100 x 1mmThermal conductivity3 W/mKElectrical ConductiveNoColorwhite

The Alphacool Eisschicht Ultra Soft are the ultimate in thermal pads. Their outstanding properties mean they can almost be compared to thermal paste. The Eisschicht Ultra Soft pads fit much better to components, which contributes to excellent cooling performance.Better than standard thermal pads?The ultra-soft material of the Eisschicht Ultra Soft thermal pads acts in a similar way to thermal paste. While normal thermal pads are simply pressed together by the contact pressure, which can lead to uneven contact pressure on components of different heights, this is almost impossible with the Eisschicht Ultra Soft thermal pads. The material spreads as well as thermal paste and thus prevents the highest components from being subjected to increased contact pressure from the cooler. In the worst case, this can lead to the PCB bending. The soft consistency also fills in any uneven areas much better. The Eisschicht Ultra Soft thermal pads therefore cling much better to the components, which of course benefits heat transfer.But that’s not the only advantage!The special material also cannot dry out. Usually the silicone in thermal pads bleeds over time. This causes them to become hard and the performance of the pads drops rapidly at a certain point. This is not the case with the Eisschicht Ultra Soft thermal pads. They can be used for a much longer period of time without losing any significant performance.A thermal pad with fabric?The consistency of the heat-conducting material is similar to a viscous thermal paste. A special fabric is embedded so that the material remains stable and can be used as a thermal pad. This ensures perfect distribution of the material if the element to be cooled has an uneven shape. Examples of this include voltage converters, VRam and similar electronic components of all kinds that require cooling.Cropping? No problem!When cutting the thermal pads, you should definitely leave the foil on the pads. This means that the pads can be easily cut to size with scissors. It's just as easy as cutting paper. The cut edges stay perfectly clean and don't fray.The Alphacool Eisschicht Ultra Soft thermal pads are superior to the usual thermal pads in many ways and are also used in all new Eisblock Aurora graphics card coolers from Alphacool. Technical dataDimensions (L x W x H)100 x 100 x 3mmThermal conductivity3 W/mKElectrical ConductiveNoColorwhite

This item is a replacement lid for the Alphacool Eisstation.Compatible with all variants with item numbers: 15272, 15273, 15274

Pumpenaufsatz mit Ausgleichsbehälter, für DC-LT-Pumpen geeignet, Montage an 40-mm-Radiator

Besides the daily work at a PC, there are many Alphacool employees who often enjoy playing a few rounds on the PC. For this reason, it only made sense to develop a mousepad that is perfectly suited for working at the office and playing on the computer. The most important foundations were quickly established. Simplicity:Colourful pictures and multi-coloured abstract art will definitely not be present on its surface. It should appear elegant and simple, so the entire surface is matte black. Only a small, discreet Alphacool logo indicates the manufacturer. Perfect Anti-Friction Properties and Slip-Proof:Annoying obstacles that make working and playing difficult should not occur. For this reason, Alphacool has placed a finely-structured cloth cover on the surface, which should create minimal friction resistance.The bottom of the "Eisteppich" is made entirely of rubber, so the mousepad slipping and sliding away is nearly impossible. Comfortable Support:With many mousepads, your hand has to rest on it for hours. That means your mousepad has to be comfortable. Under the cloth surface, there is a special thin foam which has a little give when pressure is applied. This means the mousepad is a comfortable surface for your hand to lie on for hours of work or play. This is also aided by the mousepad's slight thickness, a mere 3mm. This means no annoying edges to get in the way. High Quality:The "Eisteppich" is made of three very different materials. The full rubber bottom, a special foam layer in the middle and the robust cloth cover on the surface. All the materials are bound together with a special heat treatment. This binding is so secure that Alphcaool does not need to sew the edges together to avoid the edges shifting. It is simply no longer necessary. All these points make the Alphacool "Eisteppich" the ideal pad for anyone looking for the perfect mousepad for work or play. Special Features: Anti-slip rubber layer Dense foam, not too hard and not too soft for the hand Selected fabric for longer lifespan Specially treated surface for a perfectly gliding mouse Easy to clean (clear water and a cloth) Technical Details: Measurements (LxWxH): 900 x 400 x 3mm Materials: Rubber, foam, fabric Colour: Black Scope of Delivery: 1x Alphacool Eisteppich Mousepad Black Monsta

If you have already cut PETG tubing, you may have run into the problem of unclean and uneven ends. This means you must further process the tubing making everything much more cumbersome. This is now a thing of the past! With the Eistools Modding Cutter, Alphacool launches a versatile product on the market with which you can cut your hard tubes cleanly without great effort. It is also very good for modders!No More Sawing PETG! The well-known process remains the same: Heat up the Hardtube, cut it to the desired length, done! Alphacool does not reinvent the wheel here but improves the results many times over. Of course, the you can use the Eistools Modding Cutter with soft tubing too.What's with the angle? The biggest feature of our new tool is probably the use of different angles on the pliers. These are used especially in other parts of the PC. If you have ever modded a PC, you will know how useful cutting a perfect angle can be. If you want to cut some U-channel at a 45-degree angle – no problem! If you have some light defusing material that needs to be flush – no problem! If your blade gets blunt over time, we've of course taken precautions as well. Replacement blades for your modding cutter can be found under article number 1015313.

Once you realise how versatile the Alphacool Eistool Modding Cutters can be, you will be using them for many applications and even the best tinkerers and modders can have an accident. Alphacool now offers replacement blades for your tools if yours are no longer as sharp as they once were. Replacing the blades is easy: Loosen the nut and bold, the old blade can be removed and a new one inserted. It doesn't get much more simple as that!

Hochwertiges Entgratungs-Tool, für Hard-Tubes aus Kunststoff oder Metall, entgratet Innen- und Außenkanten

With Alphacool Eiswasser, water cooling pioneer Alphacool is checking off every modder and enthusiast’s wish list: brilliant colours, cool effects in plexi coolers, tubing and reservoirs, as well as a long lifespan and material compatibility. The Alphacool Eiswasser Crystal Series has been tested in every possible application both in Alphacool’s lab and by external testers and modders, and was proven to be high-quality and long-lasting.If you’re looking to add some illumination to your PC, the Alphacool Eiswasser Crystal UV is for you. It has excellent UV-reactivity with UV-LEDs or cathodes.Alphacool Eiswasser gives your water cooling system an extra visual highlight with great cooling performance.Note: This cooling liquid does not contain any biocides or anti-corrosion additives. It should also be noted that the loop must be cleaned more frequently when using this colored liquid. The dyes it contains can clog the circuit after a long period of use and impair cooling performance. Alphacool's Eiswasser series is therefore more suitable for use in show cases than in gaming or work PCs. Technical dataColortransparentUV inkblueContent1000mlSpecificationReady mixManufacturerAlphacool

With Alphacool Eiswasser, water cooling pioneer Alphacool is checking off every modder and enthusiast’s wish list: brilliant colours, cool effects in plexi coolers, tubing and reservoirs, as well as a long lifespan and material compatibility. The Alphacool Eiswasser Crystal Series has been tested in every possible application both in Alphacool’s lab and by external testers and modders, and was proven to be high-quality and long-lasting.If you’re looking to add some illumination to your PC, the Alphacool Eiswasser Crystal UV is for you. It has excellent UV-reactivity with UV-LEDs or cathodes.Alphacool Eiswasser gives your water cooling system an extra visual highlight with great cooling performance.Note: This cooling liquid does not contain any biocides or anti-corrosion additives. It should also be noted that the loop must be cleaned more frequently when using this colored liquid. The dyes it contains can clog the circuit after a long period of use and impair cooling performance. Alphacool's Eiswasser series is therefore more suitable for use in show cases than in gaming or work PCs. Technical dataUV inkNot UV activeContent1000mlSpecificationReady mixColorgreenManufacturerAlphacool

With Alphacool Eiswasser, water cooling pioneer Alphacool is checking off every modder and enthusiast’s wish list: brilliant colours, cool effects in plexi coolers, tubing and reservoirs, as well as a long lifespan and material compatibility. The Alphacool Eiswasser Crystal Series has been tested in every possible application both in Alphacool’s lab and by external testers and modders, and was proven to be high-quality and long-lasting.If you’re looking to add some illumination to your PC, the Alphacool Eiswasser Crystal UV is for you. It has excellent UV-reactivity with UV-LEDs or cathodes.Alphacool Eiswasser gives your water cooling system an extra visual highlight with great cooling performance.Note: This cooling liquid does not contain any biocides or anti-corrosion additives. It should also be noted that the loop must be cleaned more frequently when using this colored liquid. The dyes it contains can clog the circuit after a long period of use and impair cooling performance. Alphacool's Eiswasser series is therefore more suitable for use in show cases than in gaming or work PCs. Technical dataContent1000mlSpecificationReady mixColorgreenUV inkgreenManufacturerAlphacool

Vorgemischte Kühlflüssigkeit von Alphacool, 1.000 ml Inhalt, Rot, langlebige Farbstabilität, dauerhaft einsetzbar, geringe elektrische Leitfähigkeit, sehr guter thermischer Leitwert

The Eiswind fans in the Pure Edition are based on the worldwide popular be quiet! fans. The finely ribbed fan blades ensure optimum air flow and targeted turbulence to minimize background noise. The high-quality rifle bearing also contributes to smooth running. The fans can be controlled via the 4-pin PWM connector. The fans can be controlled over a wide speed range.

The Alphacool Eiswolf 2 is the first full cover GPU AIO waterblock from Alphacool. It is based on the Alphacool GPX Eisblock Aurora GPX water block, a pump unit and a 360mm NexXxoS ST30 full copper radiator. The latter is equipped with the Alphacool Aurora Rise Digital RGB fans.Fullcover Waterblock?The Eiswolf 2 graphics card AIO water block not only cools the GPU with liquid but also all relevant components that require active cooling. This includes the graphics memory, the VRM and, if necessary, other components that require direct cooling. By using the Eisblock GPX Aurora water cooler, the cooling capacity is identical to that of a DIY graphics card water cooler.PumpThe Eiswolf 2 has a pump unit in place of the normal connection terminal. This pump unit houses the DC-LT 2 pump. An improved and quieter version of the well-known DC-LT Low Noise Ceramic Pump. Despite looking rather large, the pump unit is only 5 mm wider than a normal connection terminal.Fittings and TubingAs with all new AIO units, Alphacool uses only TPV hoses from the Enterprise Solution range for (usually reserved for servers and workstations) in the Eiswolf 2. The tubing is made of EPDM/PP and are extremely heat-resistant, durable, and free of plasticizers. All fittings are also based on the Enterprise Solution range and match the TPV hoses perfectly.ExpandabilityBy using the quick-release fastener, the Eiswolf 2 can be connected to another Alphacool AIO unit to achieve a larger loop in seconds. Alphacool offers various prefilled components with which the loop can be easily extended. For safety reasons, the quick-release fasteners are firmly screwed together and not just plugged together.Lighting and fansThe Eiswolf 2 cooler has a digital RGB LED lighting, also called addressable RGB LEDs. They run along the entire back of the graphics card cooler and provide complete illumination of the water cooler. The pump unit is more discreet and offers a green glowing logo for Nvidia and a red glowing logo for AMD cards. The name "Eiswolf" on the pump unit remains unlit, discreetly in the background. The fan used is the Aurora Rise with 120mm. Due to the special blade design, the fan is extremely quiet and the addressable RGB LEDs provide brilliant illumination. The Alphacool Aurora Rise fan convinces with a max. static pressure of 3.17mm/H2O and offers a max. air flow of 119.8m3/h. The PWM control allows the fan to be controlled over a wide speed range. In addition, it offers a zero control. It can therefore be regulated down to 0 rpm and then starts with approx. 350 rpm.NexXxoS RadiatorAs with all AIO units, Alphacool uses radiators from the world renowned NexXxoS series. The full copper radiators offer a much higher cooling capacity than aluminium radiators and have contributed significantly to Alphacool's worldwide success.The combination of all of the components results in a solution that is as simple as an AIO solution to install, but with the performance of a pre-assembled and prefilled custom loop.Technical note!Due to long storage times and various transport routes, the liquid in the Eiswolf 2 AIO remains still for a long time. The ingredients of the liquid can therefore deposit and lead to a brownish discoloration. As soon as the pump starts operating, the ingredients mix again and the liquid should regain an approximately clear color. This is not a reason for complaint as neither the performance nor the function of the AIO are restricted by this. If the discolouration of the cooling liquid does not disappear after the AIO has been put into operation, please contact our support team via E-Mail (info@alphacool.com). You will receive quick and uncomplicated help there. Compatibility:- Inno3D GEFORCE RTX 3090 TI ICHILL FROSTBITE- Inno3D GEFORCE RTX 3090 TI X3 OC- Nvidia 3090 Ti Founders Edition Technical data radiatorL x W x H395 x 124 x 30mm (+/- 3%)Material cooling fins, chambers & channelsCopperMaterial threadsBrassMaterial outer housingstainless steelG 1/4“ threads2 x for tubes (+ 1x Fillport G1/4“)For fan size120 mmPossible fan assembly3 x one-sided / 6 x both-sidedTechnical data cooler and pumpL x W x H220,5 x 156,05 x 46mmMaterial cooler bottomChrome plated copperMaterial cooler topacrylicThreads2 x G1/4“Pump typeDC-LT 2Pump speed2600 rpm (+/- 10%)Head of delivery1 mMaximum flow rate72 L/hVoltage6-13.5V DCPower consumption3.2WMTBF50.000 hTechnical data liquidColorclearIngredient 1Destilled water (CAS-number 7732-18-5)Ingredient 2Glysantin (CAS-number 1017-21-1)Working temperatures-15 C° / +90 °CTechnical data quick fastenersL x D95 x 27mmMaterialNylonFor tube size12,7 / 7,6mmColorBlackTechnical data fittingsL x D straight fitting24 x 18mmQuantity straight fittings2xL x B x H 90° fitting35 x 27 x 17mmQuantity 90° fittings2xFor tube size12,7 / 7,6mmMaterial fittingsBrassTechnical data tubeLength50cmMaterial tubeTPV (EPDM/PP)ColorMatt blackTube size12,7 / 7,6mmHardness grade35 Shore-A to 50 Shore-DWorking temperature-50 to +155 °CTechnical data fanSpeed0 - 2500 RPMStatic pressure3,17 mm H2OAir flow rate119,8 m³/hBearingsSleeve bearingFan connector4-Pin PWMConnection Digital aRGB3-Pin JST + 3-Pin 5VDimensions120 x 120 x 25mmNet weight187gMax working temperature60°C

The Alphacool Eiswolf 2 is the first full cover GPU AIO waterblock from Alphacool. It is based on the Alphacool Eisblock Aurora GPX water block, a pump unit and a 360mm NexXxoS ST30 full copper radiator. The latter is equipped with the Alphacool Aurora Rise Digital RGB fans.Fullcover Waterblock?The Eiswolf 2 graphics card AIO water block not only cools the GPU with liquid but also all relevant components that require active cooling. This includes the graphics memory, the VRM and, if necessary, other components that require direct cooling. By using the Eisblock GPX Aurora water cooler, the cooling capacity is identical to that of a DIY graphics card water cooler.PumpThe Eiswolf 2 has a pump unit in place of the normal connection terminal. This pump unit houses the DC-LT 2 pump. An improved and quieter version of the well-known DC-LT Low Noise Ceramic Pump. Despite looking rather large, the pump unit is only 5 mm wider than a normal connection terminal.Fittings and TubingAs with all new AIO units, Alphacool uses only TPV hoses from the Enterprise Solution range for (usually reserved for servers and workstations) in the Eiswolf 2. The tubing is made of EPDM/PP and are extremely heat-resistant, durable, and free of plasticizers. All fittings are also based on the Enterprise Solution range and match the TPV hoses perfectly.ExpandabilityBy using the quick-release fastener, the Eiswolf 2 can be connected to another Alphacool AIO unit to achieve a larger loop in seconds. Alphacool offers various prefilled components with which the loop can be easily extended. For safety reasons, the quick-release fasteners are firmly screwed together and not just plugged together.Lighting and fansThe Eiswolf 2 cooler has a digital RGB LED lighting, also called addressable RGB LEDs. They run along the entire back of the graphics card cooler and provide complete illumination of the water cooler. The pump unit is more discreet and offers a green glowing logo for Nvidia and a red glowing logo for AMD cards. The name "Eiswolf" on the pump unit remains unlit, discreetly in the background. The fan used is the Aurora Rise with 120mm. Due to the special blade design, the fan is extremely quiet and the addressable RGB LEDs provide brilliant illumination. The Alphacool Aurora Rise fan convinces with a max. static pressure of 3.17mm/H2O and offers a max. air flow of 119.8m3/h. The PWM control allows the fan to be controlled over a wide speed range. In addition, it offers a zero control. It can therefore be regulated down to 0 rpm and then starts with approx. 350 rpm.NexXxoS RadiatorAs with all AIO units, Alphacool uses radiators from the world renowned NexXxoS series. The full copper radiators offer a much higher cooling capacity than aluminium radiators and have contributed significantly to Alphacool's worldwide success.The combination of all of the components results in a solution that is as simple as an AIO solution to install, but with the performance of a pre-assembled and prefilled custom loop.Technical note!Due to long storage times and various transport routes, the liquid in the Eiswolf 2 AIO remains still for a long time. The ingredients of the liquid can therefore deposit and lead to a brownish discoloration. As soon as the pump starts operating, the ingredients mix again and the liquid should regain an approximately clear color. This is not a reason for complaint as neither the performance nor the function of the AIO are restricted by this. If the discolouration of the cooling liquid does not disappear after the AIO has been put into operation, please contact our support team via E-Mail (info@alphacool.com). You will receive quick and uncomplicated help there. Compatibility:- Asus ROG Strix LC GeForce RTX 3090 Ti OC, ROG-STRIX-LC-RTX3090TI-O24G-GAMING, 24GB GDDR6X (90YV0HC0-M0NA00)- Asus ROG Strix LC GeForce RTX 3090 Ti, ROG-STRIX-LC-RTX3090TI-24G-GAMING, 24GB GDDR6X (90YV0HC2-M0NA00)- Asus TUF Gaming GeForce RTX 3090 Ti OC, TUF-RTX3090TI-O24G-GAMING, 24GB GDDR6X (90YV0HC1-M0NA00)- Asus TUF Gaming GeForce RTX 3090 Ti, TUF-RTX3090TI-24G-GAMING, 24GB GDDR6X (90YV0HC3-M0NA00) Technical data radiatorL x W x H395 x 124 x 30mm (+/- 3%)Material cooling fins, chambers & channelsCopperMaterial threadsBrassMaterial outer housingstainless steelG 1/4“ threads2 x for tubes (+ 1x Fillport G1/4“)For fan size120 mmPossible fan assembly3 x one-sided / 6 x both-sidedTechnical data cooler and pumpL x W x H267 x 161,84 x 48,23mmMaterial cooler bottomChrome plated copperMaterial cooler topacrylicThreads2 x G1/4“Pump typeDC-LT 2Pump speed2600 rpm (+/- 10%)Head of delivery1 mMaximum flow rate72 L/hVoltage6-13.5V DCPower consumption3.2WMTBF50.000 hTechnical data liquidColorclearIngredient 1Destilled water (CAS-number 7732-18-5)Ingredient 2Glysantin (CAS-number 1017-21-1)Working temperatures-15 C° / +90 °CTechnical data quick fastenersL x D95 x 27mmMaterialNylonFor tube size12,7 / 7,6mmColorBlackTechnical data fittingsL x D straight fitting24 x 18mmQuantity straight fittings2xL x B x H 90° fitting35 x 27 x 17mmQuantity 90° fittings2xFor tube size12,7 / 7,6mmMaterial fittingsBrassTechnical data tubeLength50cmMaterial tubeTPV (EPDM/PP)ColorMatt blackTube size12,7 / 7,6mmHardness grade35 Shore-A to 50 Shore-DWorking temperature-50 to +155 °CTechnical data fanSpeed0 - 2500 RPMStatic pressure3,17 mm H2OAir flow rate119,8 m³/hBearingsSleeve bearingFan connector4-Pin PWMConnection Digital aRGB3-Pin JST + 3-Pin 5VDimensions120 x 120 x 25mmNet weight187gMax working temperature60°C

The Alphacool Eiswolf 2 is the first full cover GPU AIO waterblock from Alphacool. It is based on the Alphacool Eisblock Aurora GPX water block, a pump unit and a 360mm NexXxoS ST30 full copper radiator. The latter is equipped with the Alphacool Aurora Rise Digital RGB fans.Fullcover Waterblock?The Eiswolf 2 graphics card AIO water block not only cools the GPU with liquid but also all relevant components that require active cooling. This includes the graphics memory, the VRM and, if necessary, other components that require direct cooling. By using the Eisblock GPX Aurora water cooler, the cooling capacity is identical to that of a DIY graphics card water cooler.PumpThe Eiswolf 2 has a pump unit in place of the normal connection terminal. This pump unit houses the DC-LT 2 pump. An improved and quieter version of the well-known DC-LT Low Noise Ceramic Pump. Despite looking rather large, the pump unit is only 5 mm wider than a normal connection terminal.Fittings and TubingAs with all new AIO units, Alphacool uses only TPV hoses from the Enterprise Solution range for (usually reserved for servers and workstations) in the Eiswolf 2. The tubing is made of EPDM/PP and are extremely heat-resistant, durable, and free of plasticizers. All fittings are also based on the Enterprise Solution range and match the TPV hoses perfectly.ExpandabilityBy using the quick-release fastener, the Eiswolf 2 can be connected to another Alphacool AIO unit to achieve a larger loop in seconds. Alphacool offers various prefilled components with which the loop can be easily extended. For safety reasons, the quick-release fasteners are firmly screwed together and not just plugged together.Lighting and fansThe Eiswolf 2 cooler has a digital RGB LED lighting, also called addressable RGB LEDs. They run along the entire back of the graphics card cooler and provide complete illumination of the water cooler. The pump unit is more discreet and offers a green glowing logo for Nvidia and a red glowing logo for AMD cards. The name "Eiswolf" on the pump unit remains unlit, discreetly in the background. The fan used is the Aurora Rise with 120mm. Due to the special blade design, the fan is extremely quiet and the addressable RGB LEDs provide brilliant illumination. The Alphacool Aurora Rise fan convinces with a max. static pressure of 3.17mm/H2O and offers a max. air flow of 119.8m3/h. The PWM control allows the fan to be controlled over a wide speed range. In addition, it offers a zero control. It can therefore be regulated down to 0 rpm and then starts with approx. 350 rpm.NexXxoS RadiatorAs with all AIO units, Alphacool uses radiators from the world renowned NexXxoS series. The full copper radiators offer a much higher cooling capacity than aluminium radiators and have contributed significantly to Alphacool's worldwide success.The combination of all of the components results in a solution that is as simple as an AIO solution to install, but with the performance of a pre-assembled and prefilled custom loop.Technical note!Due to long storage times and various transport routes, the liquid in the Eiswolf 2 AIO remains still for a long time. The ingredients of the liquid can therefore deposit and lead to a brownish discoloration. As soon as the pump starts operating, the ingredients mix again and the liquid should regain an approximately clear color. This is not a reason for complaint as neither the performance nor the function of the AIO are restricted by this. If the discolouration of the cooling liquid does not disappear after the AIO has been put into operation, please contact our support team via E-Mail (info@alphacool.com). You will receive quick and uncomplicated help there. Compatibility:- MSI GeForce RTX 3090 Ti Gaming Trio 24G, 24GB GDDR6X (V509-029R)- MSI GeForce RTX 3090 Ti Gaming X Trio 24G, 24GB GDDR6X (V509-014R)- MSI GeForce RTX 3090 Ti Suprim 24G, 24GB GDDR6X- MSI GeForce RTX 3090 Ti Suprim X 24G, 24GB GDDR6X (V509-003R) Technical data radiatorL x W x H395 x 124 x 30mm (+/- 3%)Material cooling fins, chambers & channelsCopperMaterial threadsBrassMaterial outer housingstainless steelG 1/4“ threads2 x for tubes (+ 1x Fillport G1/4“)For fan size120 mmPossible fan assembly3 x one-sided / 6 x both-sidedTechnical data cooler and pumpL x W x H265,8 x 162,5 x 46mmMaterial cooler bottomChrome plated copperMaterial cooler topacrylicThreads2 x G1/4“Pump typeDC-LT 2Pump speed2600 rpm (+/- 10%)Head of delivery1 mMaximum flow rate72 L/hVoltage6-13.5V DCPower consumption3.2WMTBF50.000 hTechnical data liquidColorclearIngredient 1Destilled water (CAS-number 7732-18-5)Ingredient 2Glysantin (CAS-number 1017-21-1)Working temperatures-15 C° / +90 °CTechnical data quick fastenersL x D95 x 27mmMaterialNylonFor tube size12,7 / 7,6mmColorBlackTechnical data fittingsL x D straight fitting24 x 18mmQuantity straight fittings2xL x B x H 90° fitting35 x 27 x 17mmQuantity 90° fittings2xFor tube size12,7 / 7,6mmMaterial fittingsBrassTechnical data tubeLength50cmMaterial tubeTPV (EPDM/PP)ColorMatt blackTube size12,7 / 7,6mmHardness grade35 Shore-A to 50 Shore-DWorking temperature-50 to +155 °CTechnical data fanSpeed0 - 2500 RPMStatic pressure3,17 mm H2OAir flow rate119,8 m³/hBearingsSleeve bearingFan connector4-Pin PWMConnection Digital aRGB3-Pin JST + 3-Pin 5VDimensions120 x 120 x 25mmNet weight187gMax working temperature60°C

All-in-One-Wasserkühlung, für NVIDIA GeForce RTX 4080 FE, 360 mm Radiator, 3x 120-mm-PWM-Lüfter, mit integrierter RGB-Beleuchtung

All-in-One-Wasserkühlung, für MSI GeForce RTX 4080 Gaming und Suprim, 360 mm Radiator, 3x 120-mm-PWM-Lüfter, mit integrierter RGB-Beleuchtung

All-in-One-Wasserkühlung, für NVIDIA GeForce RTX 4090 FE-Grafikkarten, 360 mm Radiator, 3x 120-mm-PWM-Lüfter, mit integrierter RGB-Beleuchtung

All-in-One-Wasserkühlung, für MSI GeForce RTX 4090 Suprim-Grafikkarten, 360 mm Radiator, 3x 120-mm-PWM-Lüfter, mit integrierter RGB-Beleuchtung