Kõik hinnakirjad

"Väline kõvaketta korpuse USB 3.0 2.5 '' '

Active extension AXAGON ADR-305 USB 3.2 Gen 1 cable 5 m long. Ideal for connecting your computer to a USB device such as a mouse, keyboard, webcam, printer, scanner, plotter and others. The active USB repeater cable strengthens the passing USB signal and allows you to connect a significantly more distant USB device than the usual 5 meters when passive cables are used. The range of the cable can be further extended by using several cables in a row. Thanks to the used USB 3.2 Gen 1 (formerly USB 3.0) interface, you can enjoy a data transfer speed of up to 5 Gbps. So, you can use the cable for devices that require higher speed, such as backup systems, NAS data storage and others. A great advantage of the ADR-305 extension is an integrated auxiliary power supply connector. In most cases, USB bus power is sufficient, but for devices with larger power consumption the USB power supply may be inadequate and auxiliary power from the mains may resolve the problem. The remarkably compact body of the AXAGON repeater allows for trouble-free use in electrical installation strips or cable systems. The use of a high-quality shielded cable ensures high communication speed and minimal undesirable interference. Input: USB 3.2 Gen 1 for connection to a computer USB Type A (M) male connector Output: USB 3.2 Gen 1 for connecting a remote USB device USB Type A (F) female connector transmission rate 5000 / 480 / 12 / 1.5 Mbit/s (super / high / full / low speed) Power supply: Power supply of the cable and connected devices via USB bus (bus-power mode 5V - 500mA). For most connected USB devices, the power supply via USB bus is sufficient and no auxiliary power is required. The active part of the cable includes a Micro USB connector for additional external power supply of 5V/1-2 A. The power cable USB A-M / Micro USB, 1.2 m long is included. The cable allows powering from a standard mobile phone charger with USB-A output 5V / min. 1A, e.g. AXAGON ACU-DS16. When powering the repeater cable with the power adapter, an external 2.5" disk can be connected without the need for own power supply to the disk. For longer USB route with multiple repeater cables connected in a row, the USB bus supply may be inadequate for USB devices with lower power consumption than an external 2.5" drive. Also, in this case it can help to boost the power supply by connecting a power adapter. Other features: Fully compatible with USB 3.2 Gen 1 (USB 3.0) and backward compatible with USB 2.0 and USB 1.1. Full Plug and Play and Hot Plug support. Two LEDs indicating power and USB connection. Behind the active USB cable, a common passive USB cable can also be used. Dimensions of active part with are 75 x 24 x 13mm, cable length 5 m. Weight 208 g. Supported OS: MS Windows XP / Vista / 7 / 8 / 8.1 / 10 / 11 and later, Windows Server 2003 / 2008 / 2012 / 2016 / 2019 / 2022 and later (all 32- and 64-bit Windows versions supported), Mac OS X 10.x and higher Linux with 2.6.x kernel and higher. Note: Drivers are included with supported operating systems and will be installed automatically. No other drivers need to be installed and are not even available. Package contains: USB 3.2 Gen 1 A-M > A-F active repeater 5 m long, USB-A / Micro USB power cable, multilingual guide CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA, packed in a cardboard box.

Active extension AXAGON ADR-310 USB 3.2 Gen 1 cable 10 m long. Ideal for connecting your computer to a USB device such as a mouse, keyboard, webcam, printer, scanner, plotter and others. The active USB repeater cable strengthens the passing signal and allows you to connect a significantly more distant USB device than passive cable. The range of the cable can be further extended by using several cables in a row. Thanks to the used USB 3.2 Gen 1 (formerly USB 3.0) interface, you can enjoy a data transfer speed of up to 5 Gbps. So, you can use the cable for devices that require higher speed, such as backup systems, NAS data storage and others. A great advantage of the ADR-310 cable is an integrated auxiliary power supply connector. In most cases, USB bus power is sufficient, but for devices with larger power consumption the USB power supply may be inadequate and auxiliary power from the mains may resolve the problem. The remarkably compact body of the repeater allows for trouble-free use in electrical installation strips or cable systems. The use of a high-quality shielded cable ensures high communication speed and minimal undesirable interference. Input: USB 3.2 Gen 1 for connection to a computer USB Type A (M) male connector Output: USB 3.2 Gen 1 for connecting a remote USB device USB Type A (F) female connector Transmission rate 5000 / 480 / 12 / 1.5 Mbit/s (high / full / low speed) Power supply: Power supply of the cable and connected devices via USB bus (bus-power mode 5V - 500mA). For most connected USB devices, the power supply via USB bus is sufficient and no auxiliary power is required. The active part of the cable includes a Micro USB connector for additional external power supply of 5V/1-2 A. The power cable USB A-M / Micro USB, 1.2 m long is included. The cable allows powering from a standard mobile phone charger with USB-A output 5V / min. 1A, e.g. AXAGON ACU-DS16. When powering the repeater cable with the power adapter, an external 2.5" disk can be connected without the need for own power supply to the disk. For longer USB route with multiple repeater cables connected in a row, the USB bus supply may be inadequate for USB devices with lower power consumption than an external 2.5" drive. Also, in this case it can help to boost the power supply by connecting a power adapter. Other features: Fully compatible with USB 3.2 Gen 1 (USB 3.0) and backward compatible with USB 2.0 and USB 1.1. Full Plug and Play and Hot Plug support. Two LEDs indicating power and USB connection. Behind the active USB cable, a common passive USB cable can also be used. Dimensions of active part with are 75 x 24 x 13mm, cable length 10 m. Weight 408 g. Supported OS: MS Windows XP / Vista / 7 / 8 / 8.1 / 10 / 11 and later, Windows Server 2003 / 2008 / 2012 / 2016 / 2019 / 2022 and later (all 32- and 64-bit Windows versions supported), Mac OS X 10.x and higher Linux with 2.6.x kernel and higher. Note: Drivers are included with supported operating systems and will be installed automatically. No other drivers need to be installed and are not even available. Package contains: USB 3.2 Gen 1 A-M > A-F active repeater 10 m long, USB-A / Micro USB power cable, multilingual guide CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA, packed in a cardboard box.

SEAGATE BASIC HDD USB3 4TB Take on your day with simple, reliable backup. Simple, compact, and PC compatible, Seagate Basic portаble drive gives you additional on-the-go storage and lets you take along large files when you travel. + Leverage simple drag-and-drop usability + Expand your computer’s capacity with a lightweight, compact solution + Take advantage of instant plug-and-play PC compatibility + Transfer files fast with USB 3.0, backward-compatible with USB 2.0 Set-up for PCs is simple and straightforward: simply connect a single USB cable and you are ready to go. The drive is powered from the USB cable, so there is no need for an external power supply. And, it is automatically recognised by the Windows 1,2 operating system, so there is no software to install and nothing to configure. Just connect and take advantage of the fast data transfer speeds with the USB 3.0 interface by connecting to a SuperSpeed USB 3.0 port.

Baseus 60W USB-C car charger + Lightning cable (Black).If you're looking for a car charger that meets the demands of modern life on the go, Baseus is an excellent choice. With innovative features, durable design and complete safety, you can enjoy uninterrupted access to power wherever you are. Get rid of your worries about discharged devices and choose Baseus - a charger made for every trip.Power and convenience in one deviceThe Baseus car charger is an indispensable companion for any trip, combining reliability, functionality and versatility. With the ability to charge up to four devices simultaneously and a maximum power of 60W, you can easily charge smartphones, tablets, game consoles or car accessories.Integrated cables and USB portsA built-in 1.4-meter Lightning cable with spring-retractable function provides convenience of use and tidiness in the car, while an additional USB-C port allows fast charging of both iOS and Android devices. The built-in cables offer lightning-fast charging - for example, for the iPhone 15 up to 52% or the Huawei Mate 60 Pro up to 65% in just 30 minutes.Safety and durability at the highest levelBaseus has ensured the complete safety of your devices by equipping the charger with a 6-stage protection system, which includes protection against overload, overheating, short circuit or over voltage. The cable is made of heavy-duty TPU material and the charger's housing is made of fire-resistant PC plastic, both of which guarantee unmatched durability, ensuring a lifespan for years to come. Thanks to the non-slip hooks and locking mechanism, the charger remains stable, even during hard braking, negotiating speed bumps or driving on rough mountain roads.Compatibility without bordersThe Baseus 60W charger supports a wide range of protocols, including PD, QC, SCP, FCP and ADC, making it compatible with almost any device - from iOS and Android smartphones, tablets, or gaming consoles, to car vacuum cleaners and air purifiers. Thanks to its universal compatibility with 12-24V batteries, the charger will work well in cars, SUVs and trucks. GeneralManufacturerBaseusColorBlackModelBSCC-UC-CLWeight62,4 gMaterial of constructionPC (fire resistant plastic)InputDC 12V-24V, 7A Max.OutputUSB-A: 5V=3A, 9V=3A, 10V=2.25A, 12V=2.5A (30W Max); USB-C (C1/C2/C3): 5V=3A, 9V=3A, 12V=2.5A (30W Max); Lightning cable: 5V=3A, 9V=3A (27W Max)Total output powerUSB-A + USB-C/Lightning cable: 30W + 30W/27W; USB-A + USB-C1 + USB-C2/Lightning cable: 5V=3.4ASupported protocolsPD 3.0, QC 3.0/2.0, SCP, FCP, PPS, AFC, ADCCompatibilityiPhone (8-16/SE series), Huawei (P70/P40/Mate 60/nova series), Xiaomi (12-14 series), Samsung Galaxy (S24/S/Note 10 series), iPads, MatePads, Xiaomi tablets, Nintendo Switch, Rog Ally, Steam Deck, car vacuum cleaners, CarPlay Box, air fresheners and purifiersDimensions64 x 34 x 34 mmAdditional informationAnti-slip protection and locking mechanism, soft shell, hard core CableCable length1,4 mCable typeLightning, spring-loadedMaterial of constructionTPU

<h3>Baseus 60W USB-C car charger + Lightning cable (Black).</h3> <p>If you're looking for a car charger that meets the demands of modern life on the go, Baseus is an excellent choice. With innovative features, durable design and complete safety, you can enjoy uninterrupted access to power wherever you are. Get rid of your worries about discharged devices and choose Baseus - a charger made for every trip.</p> <p> (image) </p><h3>Power and convenience in one device</h3> <p>The Baseus car charger is an indispensable companion for any trip, combining reliability, functionality and versatility. With the ability to charge up to four devices simultaneously and a maximum power of 60W, you can easily charge smartphones, tablets, game consoles or car accessories.</p> <p> (image) </p><h3>Integrated cables and USB ports</h3> <p>A built-in 1.4-meter Lightning cable with spring-retractable function provides convenience of use and tidiness in the car, while an additional USB-C port allows fast charging of both iOS and Android devices. The built-in cables offer lightning-fast charging - for example, for the iPhone 15 up to 52% or the Huawei Mate 60 Pro up to 65% in just 30 minutes.</p> <p> (image) </p><h3>Safety and durability at the highest level</h3> <p>Baseus has ensured the complete safety of your devices by equipping the charger with a 6-stage protection system, which includes protection against overload, overheating, short circuit or over voltage. The cable is made of heavy-duty TPU material and the charger's housing is made of fire-resistant PC plastic, both of which guarantee unmatched durability, ensuring a lifespan for years to come. Thanks to the non-slip hooks and locking mechanism, the charger remains stable, even during hard braking, negotiating speed bumps or driving on rough mountain roads.</p> <p> (image) </p><h3>Compatibility without borders</h3> <p>The Baseus 60W charger supports a wide range of protocols, including PD, QC, SCP, FCP and ADC, making it compatible with almost any device - from iOS and Android smartphones, tablets, or gaming consoles, to car vacuum cleaners and air purifiers. Thanks to its universal compatibility with 12-24V batteries, the charger will work well in cars, SUVs and trucks.</p> <p> (image) </p> <div class="table-wrapper"> <p> </p> <h3>General</h3> <table> <tbody> <tr><th>Manufacturer</th><td>Baseus</td></tr><tr><th>Color</th><td>Black</td></tr><tr><th>Model</th><td>BSCC-UC-CL</td></tr><tr><th>Weight</th><td>62,4 g</td></tr><tr><th>Material of construction</th><td>PC (fire resistant plastic)</td></tr><tr><th>Input</th><td>DC 12V-24V, 7A Max.</td></tr><tr><th>Output</th><td>USB-A: 5V=3A, 9V=3A, 10V=2.25A, 12V=2.5A (30W Max); USB-C (C1/C2/C3): 5V=3A, 9V=3A, 12V=2.5A (30W Max); Lightning cable: 5V=3A, 9V=3A (27W Max)</td></tr><tr><th>Total output power</th><td>USB-A + USB-C/Lightning cable: 30W + 30W/27W; USB-A + USB-C1 + USB-C2/Lightning cable: 5V=3.4A</td></tr><tr><th>Supported protocols</th><td>PD 3.0, QC 3.0/2.0, SCP, FCP, PPS, AFC, ADC</td></tr><tr><th>Compatibility</th><td>iPhone (8-16/SE series), Huawei (P70/P40/Mate 60/nova series), Xiaomi (12-14 series), Samsung Galaxy (S24/S/Note 10 series), iPads, MatePads, Xiaomi tablets, Nintendo Switch, Rog Ally, Steam Deck, car vacuum cleaners, CarPlay Box, air fresheners and purifiers</td></tr><tr><th>Dimensions</th><td>64 x 34 x 34 mm</td></tr><tr><th>Additional information</th><td>Anti-slip protection and locking mechanism, soft shell, hard core</td></tr> </tbody> </table><p> </p> <h3>Cable</h3> <table> <tbody> <tr><th>Cable length</th><td>1,4 m</td></tr><tr><th>Cable type</th><td>Lightning, spring-loaded</td></tr><tr><th>Material of construction</th><td>TPU</td></tr> </tbody> </table> </div>

A-Data HD650 2.5" 1TB, USB 3.0

Act Dual kõvaketta dokkimisjaam, Usb 3.0 Hdd dokkimisjaam 2.5"/3.5" Sata Hdd/sdd jaoks, toetab võrguühenduseta kloonimist, varundusfunktsioon - Ac1504

Adapter StarTech US2GC30 USB 3.0 Type-C / 2.5 Gigabit Etherne

The HD650 combines state-of-the-art materials with precise engineering to create an external storage solution that features improved ruggedness and data safety. The drive utilizes an ultra-fast USB 3.0 interface for improved transfer speed, and an azure LED indicates power and transfer status. Its flowing lines and striking colors make it a great looking storage option for valuable files, especially for people with active and outdoor lifestyles.

The HD650 combines state-of-the-art materials with precise engineering to create an external storage solution that features improved ruggedness and data safety. The drive utilizes an ultra-fast USB 3.0 interface for improved transfer speed, and an azure LED indicates power and transfer status. Its flowing lines and striking colors make it a great looking storage option for valuable files, especially for people with active and outdoor lifestyles.

Adata HD650 2.5" 1TB, USB 3.0, Punane

The HD650 combines state-of-the-art materials with precise engineering to create an external storage solution that features improved ruggedness and data safety. The drive utilizes an ultra-fast USB 3.0 interface for improved transfer speed, and an azure LED indicates power and transfer status. Its flowing lines and striking colors make it a great looking storage option for valuable files, especially for people with active and outdoor lifestyles.

Lihtne ja kaasaegne välimus; Põrutuskindel; SuperSpeed ​​USB 3.0 liides; Kriimustuskindel pind; LED indikaator näitab allalaadimise staatust

A-Data kõvaketas DashDrive HD720 1TB USB 3.0 sinine; Vee- ja põrutuskindel

Aisens - Asds-d02w - Asds-d02w Sata 2.5/3.5a Usb 3.0/3.1 Gen1 dokkimisjaam kloonimiseks, valge

Aisens - ase-2520b - väline korpus 2.5" 9.5 mm sata a usb 3.0/usb3.1 gen1, must

<p data-start="75" data-end="491" class=""><strong data-start="75" data-end="164">20 W kompaktne reisitarvik Power Delivery ja Quick Charge toega – kiireks laadimiseks</strong><br data-start="164" data-end="167"> Kõik kontrolli all: kerge ja ülikompaktne akupank on ideaalne kaaslane, kui vajad liikvel olles kiiret energialaengut. Integreeritud tekstiilkaabel muutub nutikaks kanderihmaks, mis hoiab akupanga kindlalt käes. Täiuslik kottide aasade või karabiinide külge kinnitamiseks – aku on alati käepärast ja korrastatult hoiustatud.</p><p data-start="493" data-end="802" class=""><strong data-start="493" data-end="510">Alati kaasas:</strong><br data-start="510" data-end="513"> Integreeritud tekstiilkaabel ei saa ära kaduda ja muudab akupanga usaldusväärseks laadimispartneriks kõikidele USB-C™ seadmetele.<br data-start="642" data-end="645"> Kaabel kinnitub korpuse külge ja muutub praktiliseks rihmaks, mis tagab kindla haarde käes ja sobib suurepäraselt kottide või seljakottide kinnitusaasadesse.</p><p data-start="804" data-end="1149" class=""><strong data-start="804" data-end="854">Ideaalne kuni 3 seadme samaaegseks laadimiseks</strong> – 2x USB-C™ ja 1x USB-A ühendusega (kokku kuni 20 W), sobib näiteks nutitelefoni, tahvelarvuti või juhtmevabade kõrvaklappide (nt Apple AirPods) laadimiseks.<br data-start="1012" data-end="1015"> Power Delivery (USB-C™) ja Quick Charge (USB-A) võimaldavad seadmeid ja akupanka laadida kuni 4x kiiremini kui tavaliste akupankadega.</p><p data-start="1151" data-end="1373" class=""><strong data-start="1151" data-end="1176">LED-valgustusega riba</strong> näitab akupanga järelejäänud laetuse taset.<br data-start="1220" data-end="1223"> Akupanka saab laadida kas integreeritud 13 cm USB-C™ kaabliga või USB-C™ sisend/väljundi kaudu – ühendades selle näiteks USB-laadija või sülearvutiga.</p><p> </p><p data-start="1375" data-end="1527" class=""><strong data-start="1375" data-end="1403">Universaalsed USB-pordid</strong> sobivad paljude tootjate seadmetele, näiteks Samsung Galaxy, Xiaomi, Lenovo, Huawei, samuti Apple iPhone’i või iPadi jaoks.</p>

<p data-start="62" data-end="495" class=""><strong data-start="62" data-end="151">30 W kompaktne reisitarvik Power Delivery ja Quick Charge toega – kiireks laadimiseks</strong><br data-start="151" data-end="154"> Kõik alati kontrolli all: kerge ja ülikompaktne akupank on ideaalne kaaslane liikvel olles, et tagada energialaeng just siis, kui seda vajad. Integreeritud tekstiilkattega kaabel muutub nutikaks kanderihmaks, mis hoiab akupanga kindlalt käes. Täiuslik kinnitus aasade või karabiinide külge – akupank on alati käepärast ja kenasti hoiustatud.</p><p data-start="497" data-end="824" class=""><strong data-start="497" data-end="517">Alati käepärast:</strong><br data-start="517" data-end="520"> Integreeritud tekstiilkaablit ei saa kaotada ning see muudab akupanga usaldusväärseks kaaslaseks kõigi USB-C™ seadmete laadimisel liikvel olles.<br data-start="664" data-end="667"> Kaabel kinnitub korpuse küljele ja moodustab praktilise kanderihma, mis tagab kindla haarde käes ning sobib hästi seljakottide või kottide kinnitusaasadesse.</p><p data-start="826" data-end="1160" class=""><strong data-start="826" data-end="871">Ideaalne 3 seadme samaaegseks laadimiseks</strong> – 2x USB-C™ ja 1x USB-A ühendusega (maksimaalselt 30 W), sobib nt nutitelefoni, tahvelarvuti või kõrvaklappide (nt Apple AirPods) laadimiseks.<br data-start="1014" data-end="1017"> Power Delivery (USB-C™) ja Quick Charge (USB-A) võimaldavad akupanka ja ühendatud seadmeid laadida kuni 4x kiiremini kui tavalised akupangad.</p><p data-start="1162" data-end="1363" class=""><strong data-start="1162" data-end="1187">LED-valgustusega riba</strong> näitab akupanga laetuse taset.<br data-start="1218" data-end="1221"> Akupanka saab laadida integreeritud 13 cm USB-C™ kaabliga või USB-C™ sisend/väljundi kaudu, ühendades selle nt USB-laadija või sülearvutiga.</p><p> </p><p data-start="1365" data-end="1525" class=""><strong data-start="1365" data-end="1444">Universaalsete USB-portide kaudu sobib see seadmetele paljudelt tootjatelt,</strong> nt Samsung Galaxy, Xiaomi, Lenovo, Huawei, samuti Apple iPhone'i ja iPadi jaoks.</p>

Alxum ide sata adapter, ide usb 3.0 kõvaketta adapter 2.5 ja 3.5 tolli hdd või ssd, cd-rom, cd-rw, dvd-rw draividele, kõvaketta muunduri adapterikaabel, ide usb adapter toiteallika ja usb a &

<p class="desc" style="outline: 0px; margin-right: 0px; margin-bottom: 0px; margin-left: 0px; padding: 0px; border: 0px; text-size-adjust: none; line-height: 1.3;">ARK-1220L</p><p class="desc" style="outline: 0px; margin-right: 0px; margin-bottom: 0px; margin-left: 0px; padding: 0px; border: 0px; text-size-adjust: none; line-height: 1.3;">Intel Atom E3940 QC SoC with 4K Dual HDMI/Dual LAN/M.2 DIN-Rail Fanless Box PC</p><p class="desc" style="outline: 0px; margin-right: 0px; margin-bottom: 0px; margin-left: 0px; padding: 0px; border: 0px; text-size-adjust: none; line-height: 1.3;"><br></p><p class="desc" style="outline: 0px; margin-right: 0px; margin-bottom: 0px; margin-left: 0px; padding: 0px; border: 0px; text-size-adjust: none; line-height: 1.3;">Intel Atom E3940 Quad Core SoC turbo burst up to 1.8 GHz</p><p class="desc" style="outline: 0px; margin-right: 0px; margin-bottom: 0px; margin-left: 0px; padding: 0px; border: 0px; text-size-adjust: none; line-height: 1.3;">DIN-Rail system with essential I/O ports on front-side bezel</p><p class="desc" style="outline: 0px; margin-right: 0px; margin-bottom: 0px; margin-left: 0px; padding: 0px; border: 0px; text-size-adjust: none; line-height: 1.3;">2 x Intel GbE and 4 x USB 3.0</p><p class="desc" style="outline: 0px; margin-right: 0px; margin-bottom: 0px; margin-left: 0px; padding: 0px; border: 0px; text-size-adjust: none; line-height: 1.3;">Dual HDMI display up to 4K resolution</p><p class="desc" style="outline: 0px; margin-right: 0px; margin-bottom: 0px; margin-left: 0px; padding: 0px; border: 0px; text-size-adjust: none; line-height: 1.3;">1 x full-size mPCIe with SIM holder and 1 x M.2 2230 for WIFI</p><p class="desc" style="outline: 0px; margin-right: 0px; margin-bottom: 0px; margin-left: 0px; padding: 0px; border: 0px; text-size-adjust: none; line-height: 1.3;">1 x 2.5” SATA III SSD and 1 x full-size mSATA*</p><p class="desc" style="outline: 0px; margin-right: 0px; margin-bottom: 0px; margin-left: 0px; padding: 0px; border: 0px; text-size-adjust: none; line-height: 1.3;">12V ~ 28V wide range power input</p><p class="desc" style="outline: 0px; margin-right: 0px; margin-bottom: 0px; margin-left: 0px; padding: 0px; border: 0px; text-size-adjust: none; line-height: 1.3;">Advantech WISE-PaaS support</p>

Intel B860 Express | LGA1851 | Micro-ATX | DDR5 | 8800 MHz | Memory slots 2 | 2xPCI-Express 4.0 1x | 1xPCI-Express 4.0 16x | 2xM.2 | 1xHDMI | 1xDisplayPort | 1xAudio-In | 1xAudio-Out | 1xMicrophone | 3xUSB 2.0 | 2xUSB 3.0 | 1xUSB 3.2 | 1xPS/2 | 1xRJ45 | SATA | USB-C | USB 2.0 | USB 3.2 | Serial | SATA 3.0 | Video Depending on CPU | LAN 2.5 Gigabit | Audio | RAID SATA 0, 1, 5, 10 | TPM Header

The AXAGON ACU-DPQ100 GaN travel wall charger enables fast charging of up to three mobile devices at the same time. With 100W of total power, the charger charges notebooks, phones and other mobile devices at the highest possible speed. The adapter offers a standard USB-A connector, but also two double-sided USB-C connectors. Compact size and high performance is given by the new GaN technology used. The components used with Galium Nitride work with high efficiency, which allows you to achieve high performance with a small size. The charger is equipped with two Power Delivery 3.0 / Quick Charge 4+ USB Type-C outputs and one Quick Charge 3.0 USB Type-A output, enabling fast charging of not only smartphones and tablets, but also laptops. The Quick Charge 4+ technology allows up to 4 times faster charging of phones than a standard USB charger. Power Delivery 3.0 technology not only supports charging of modern phones, but also enables 100W PD charging of powerful laptops. The charger supports 20W PD charging for iPhone 12, 13, 14 and 15 and also offers 27W PD charging for iPhone 13 Pro, 14 Pro, 15 Pro and their Pro Max models. In addition, it supports 25W SFC charging for Samsung Galaxy S20 - S24, Note and Z Fold series and also offers 45W SFC 2.0 charging for Samsung Galaxy S20 - S24 Ultra, Tab S7+ - S9+, Tab S8 - S9 Ultra. The adapter is also compatible with other fast phone charging standards such as Apple iPhone, iPad, Samsung, Huawei, Honor, Xiaomi. The main advantage of the power adapter is the Power Delivery 3.0 standard for charging Apple MacBook, Lenovo, Asus, HP, Dell and other laptops. You can charge your laptop directly or with the increasingly popular docking stations and port replicators. The advanced protection system at the charging adapter output protects the device being charged from damage. The charger function also detects the device being charged and selects the optimal charging speed and progress. The body of the power adapter has a pleasant shape and size. Compared to classic charging adapters with the same parameters, the size of this charger is up to half the size. The combination of small dimensions, achieved with GaN technology and a wide range of input voltages, makes the charger an ideal travel helper. Input: input voltage AC 100V-240V / 2A / 50-60 Hz (WIV function) supports multiple national power standards two-pin euro plug - integrated in the body of the charger Outputs: USB-A port QC (phones) max. 30W: 4.5V/5A, 5V/3A, 9V/3A, 12V/2.5A, 20V/1.5A Charging technology: QC 3.0, QC 2.0, AFC, SCP, FCP, PE+, SMART, Apple 2.4A USB-C port PD2 (phones) max. 65W: 5V/3A, 9V/3A, 12V/2.5A, 15V/3A, 20V/3.25A, PPS: 3.3-11V/3A Charging technology: PD 3.0, PD 2.0, PPS, QC4+, QC 3.0, QC 2.0, SFC 2.0, SFC, AFC, SCP, FCP, PE+, SMART, Apple PD USB-C port PD1 (laptops, phones) max. 100W: 5V/3A, 9V/3A, 12V/2.5A, 15V/3A, 20V/5A, PPS: 3.3-11V/5A Charging technology: PD 3.0, PD 2.0, PPS, QC4+, QC 3.0, QC 2.0, SFC 2.0, SFC, AFC, SCP, FCP, PE+, SMART, Apple PD Maximum performance using multiple ports: maximum power QC + PD2 15W, SMART mode charging is used (max. 5V/3A) maximum power QC + PD1 83W maximum power PD1 + PD2 85W maximum power QC + PD1 + PD2 80W total maximum power 100W total maximum current 5A Supported charging technologies: Standard charging of all devices that support 5V and Apple iPhone 5, 6, SE, 7 charging. SMART - charging max. 5V/3A, Quick Charge 1.0, USB Battery Charging 1.2 (DCP 1.5A) and Apple 2.4A (iPad). PE+ - quick charging using MediaTek Pump Express+ and Pump Express+ 2.0 protocol. FCP - quick charging of devices that support Huawei Fast Charge Protocol. SCP - quick charging (up to 40W) using the Huawei SuperCharge Protocol. AFC - quick charging using the Samsung Adaptive Fast Charging protocol. SFC - quick charging using Samsung Super Fast Charging and Super Fast Charging 2.0 protocol. QC - quick charging using the Qualcomm Quick Charge 2.0, Quick Charge 3.0 and Quick Charge 4+ protocol. PPS - quick charging using the Programmable Power Supply protocol (part of USB PD 3.0 and QC4+). PD - quick charging using USB Power Delivery 2.0 and Power Delivery 3.0 protocol. Examples of supported phones, tablets and laptops: SFC - quick charging (up to 25W) of Samsung Galaxy S20, S21, S22, S23, S24 series, Note 10, 20 series, Z Fold 2, 3, 4 series. SFC 2.0 - quick charging (up to 45W) of Samsung Galaxy S20, S21, S22, S23, S24 Ultra, Tab S7+, Tab S8+, Tab S9+, Tab S8 Ultra, Tab S9 Ultra. PD - quick charging of Apple iPhone 8, 8 Plus, X, XS, XS Max, XR, 11, 11 Pro, 11 Pro Max phone. PD - quick charging (up to 20W) Apple iPhone 12, 12 Mini, 12 Pro, 12 Pro Max, 12, 12 Mini, 12 Pro, 12 Pro Max, 13, 13 Mini, 14, 14 Plus, 15, 15 Plus phone. PD - quick charging (up to 27W) Apple iPhone 13 Pro, 13 Pro Max, 14 Pro, 14 Pro Max, 15 Pro, 15 Pro Max phone. PD - quick charging (up to 100W) ofLenovo, HP, Dell, Acer, Asus, Apple MacBook Air, MacBook Pro, iPad mini, iPad Air, iPad Pro and others notebooks. The charger supports WIV, AIC and CC functions: Wide Input Voltage - function of a wide range of input voltage; it protects the adapter against undervoltage and overvoltage at the input and allows the use of more national power standards. Automatic Intelligent Communication - function of automatic recognition of the connected device to select optimal charging parameters. Constant Output Current - the current hold function prevents the output power fluctuations; this function ensures steady course of charging. Complex output protection: OCP, OVP, OTP, OSP: Over Current Protection. Protection of output against current overload. Over Voltage Protection. Protection against overvoltage at the output. Over Temperature Protection. Protection against overheating of the adapter. Output Short Circuit protection. Short circuit protection at the output. Other features: dimensions of the charger body 115 x 60 x 32 mm including a plug, weight: 242 g, material: non-flammable plastic. Package contains: black wall charger, multilingual guide CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA, packed in a cardboard box with a hanging hole.

Compact travel wall charger AXAGON ACU-DPQ65 GaN for fast charging of up to three mobile devices at a time. With 65W of total power, the charger charges notebooks, phones and other mobile devices at the highest possible speed. The adapter offers a standard USB-A connector, but also two double-sided USB-C connectors. Ultra compact size and high performance is given by the new GaN technology used. The components used with Galium Nitride work with high efficiency, which allows you to achieve high performance with a small size. Two Power Delivery 3.0 / Quick Charge 4+ USB type C outputs and one Quick Charge 3.0 USB type A output allow fast charging of smartphones and tablets but also charging of laptops. The charger is compatible with fast charging standards for Apple iPhones, iPads, Samsung, Huawei, Honor, Xiaomi, as well as PD charging for Lenovo, HP, Dell and other notebooks. The Quick Charge 4+ technology allows up to 4 times faster charging of phones than a standard USB charger. The Power Delivery 3.0 technology provides support for modern phones, but also for charging modern laptops. The AIC function recognizes the connected device and automatically selects the optimal charging speed, while the CC function ensures steady course of charging. WIV function works with wide range of input voltages, it protects the adapter against undervoltage and input overvoltage, and allows the use of multiple "national power supply standards". The advanced protection system at the charging adapter output protects the device being charged from damage. The body of the power adapter has a pleasant shape and size. Compared to classic charging adapters with same parameters, the size of the charger is a third to a half smaller. The combination of small dimensions, achieved with GaN technology and a wide range of input voltages, makes the charger an ideal travel helper. The operation of the charger is indicated by an elegant white LED that does not dazzle. Input: input voltage AC 100V-240V / 50-60 Hz (WIV function) supports multiple national power standards two-pin euro plug - integrated in the body of the charger Outputs: three outputs 1x USB type A port QC (phones): Quick Charge 3.0 - 4.5V/5A, 5V/4.5A, 9V/3A, 12V/2.5A, 15V/2A, 20V/1.5A 1x USB type C port PD2 (phones): Power Delivery 3.0 - 5V/3A, 9V/3A, 12V/2.5A, 15V/2A, 20V/1.5A 1x USB type C port PD1 (notebooks, phones): Power Delivery 3.0 - 5V/3A, 9V/3A, 12V/3A, 15V/3A, 20V/3.25A QC port maximum power 30W PD2 port maximum power 33W PD1 port maximum power 65W QC + PD1 maximum power 63W QC + PD2 maximum power 24W PD1 + PD2 maximum power 63W QC + PD1 + PD2 maximum power 60W total maximum power 65W total maximum current 5A Supported charging technologies: USB type A port QC (max. 30W): Fast charging QC2.0, QC3.0, AFC, FCP, SCP, PE+, SMART charging max. 5V/4.5A USB type C ports PD1 (max. 65W) and PD2 (max. 33W): Fast charging PD 2.0, PD 3.0, QC2.0, QC3.0, QC4+, AFC, FCP, PE+, PSS 3.3-11V/3A, SMART charging max. 5V/3A, Apple fast charging The charger charges devices with the following technologies: Standard charging of all devices that support 5V and Apple iPhone 5, 6, SE, 7 charging. Smart 5V/4.5A Qualcomm Quick Charge 1.0, USB Battery Charging 1.2 (DCP 1.5A) and Apple 2.4A (iPad). QC - quick charging of devices that support Qualcomm Quick Charge 2.0, Quick Charge 3.0 and Quick Charge 4+. AFC - quick charging of devices that support Samsung Adaptive Fast Charging. FCP - quick charging of devices that support Huawei Fast Charge Protocol. SCP - quick charging of devices that support Huawei SuperCharge Protocol. PE+ - quick charging of devices that support MediaTek Pump Express+ and Pump Express+ 2.0. PPS - charging using Programable Power Supply protocol (part USB PD 3.0 and QC4+) 3.3 - 11V / 3A. PD - quick charging of devices that support Power Delivery 2.0 and Power Delivery 3.0. PD - quick charging of Apple iPhone 8, 8 Plus, X, XS, XS Max, XR, 11, 11 Pro, 11 Pro Max phone. PD - quick charging (up to 20W) of Apple iPhone 12 mobile and charging of Apple MacBook, MacBook Pro, iPad Pro, iPad Air. PD - quick charging (up to 65W) of Lenovo, HP, Dell, Apple MacBook, Acer, Asus etc notebooks. The charger supports WIV, AIC and CC functions: Wide Input Voltage - function of a wide range of input voltage; it protects the adapter against undervoltage and overvoltage at the input and allows the use of more national power standards. Automatic Intelligent Communication - function of automatic recognition of the connected device to select optimal charging parameters. Constant Output Current - the current hold function prevents the output power fluctuations; this function ensures steady course of charging. Complex output protection: OCP, OVP, OTP, OSP: Over Current Protection - protection of output against current overload. Over Voltage Protection - protection against overvoltage at the output. Over Temperature Protection - protection against overheating of the adapter. Output Short Circuit protection - short circuit protection at the output. Other features: dimensions of the charger body 103 x 36 x 32mm including a plug, weight: 118 g, material: non-flammable plastic. Package contains: wall charger, multilingual manual CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / BG / CN / TR / ARA, packed in a cardboard box with a hanging hole.

The AXAGON ACU-DPQ65W GaN travel wall charger enables fast charging of up to three mobile devices at the same time. With 65W of total power, the charger charges notebooks, phones and other mobile devices at the highest possible speed. The adapter offers a standard USB-A connector, but also two double-sided USB-C connectors. Compact size and high performance is given by the new GaN technology used. The components used with Galium Nitride work with high efficiency, which allows you to achieve high performance with a small size. The charger is equipped with two Power Delivery 3.0 / Quick Charge 4+ USB Type-C outputs and one Quick Charge 3.0 USB Type-A output, enabling fast charging of not only smartphones and tablets, but also laptops. The Quick Charge 4+ technology allows up to 4 times faster charging of phones than a standard USB charger. Power Delivery 3.0 technology not only supports charging of modern phones, but also enables 65W PD charging of powerful laptops. The charger supports 20W PD charging for iPhone 12, 13, 14 and 15 and also offers 27W PD charging for iPhone 13 Pro, 14 Pro, 15 Pro and their Pro Max models. In addition, it supports 25W SFC charging for Samsung Galaxy S20 - S24, Note and Z Fold series and also offers 45W SFC 2.0 charging for Samsung Galaxy S20 - S24 Ultra, Tab S7+ - S9+, Tab S8 - S9 Ultra. The adapter is also compatible with other fast phone charging standards such as Apple iPhone, iPad, Samsung, Huawei, Honor, Xiaomi, as well as the Power Delivery 3.0 standard for charging Apple MacBook, Lenovo, Asus, HP, Dell and other laptops. The advanced protection system at the charging adapter output protects the device being charged from damage. The charger function also detects the device being charged and selects the optimal charging speed and progress. The body of the power adapter has a pleasant shape and size. Compared to classic charging adapters with the same parameters, the size of this charger is up to half the size. The combination of small dimensions, achieved with GaN technology and a wide range of input voltages, makes the charger an ideal travel helper. The operation of the charger is indicated by an elegant LED. Input: input voltage AC 100V-240V / 1.5A / 50-60 Hz (WIV function) supports multiple national power standards two-pin euro plug - integrated in the body of the charger Outputs: USB-A port QC (phones) max. 30W: 4.5V/5A, 5V/4.5A, 9V/3A, 12V/2.5A, 15V/2A, 20V/1.5A Charging technology: QC 3.0, QC 2.0, AFC, SCP, FCP, PE+, SMART, Apple 2.4A USB-C port PD2 (phones) max. 33W: 5V/3A, 9V/3A, 12V/2.5A, 15V/2A, 20V/1.5A, PPS: 3.3-11V/3A Charging technology: PD 3.0, PD 2.0, PPS, QC4+, QC 3.0, QC 2.0, SFC, AFC, SCP, FCP, PE+, SMART, Apple PD USB-C port PD1 (laptops, phones) max. 65W:5V/3A, 9V/3A, 12V/3A, 15V/3A, 20V/3.25A, PPS: 3.3-11V/5A Charging technology: PD 3.0, PD 2.0, PPS, QC4+, QC 3.0, QC 2.0, SFC 2.0, SFC, AFC, SCP, FCP, PE+, SMART, Apple PD Maximum performance using multiple ports: maximum power QC + PD2 24W, SMART mode charging is used (max. 5V/4.5A) QC + PD1 maximum power 63W PD1 + PD2 maximum power 63W QC + PD1 + PD2 maximum power 60W total maximum power 65W total maximum current 5A Supported charging technologies: Standard charging of all devices that support 5V and Apple iPhone 5, 6, SE, 7 charging. SMART - charging max. 5V/4.5A, Quick Charge 1.0, USB Battery Charging 1.2 (DCP 1.5A) and Apple 2.4A (iPad). PE+ - quick charging using MediaTek Pump Express+ and Pump Express+ 2.0 protocol FCP - quick charging using Huawei Fast Charge Protocol. SCP - quick charging (up to 20W) using Huawei SuperCharge Protocol. AFC - quick charging using Samsung Adaptive Fast Charging protocol. SFC - quick charging using Samsung Super Fast Charging and Super Fast Charging 2.0 protocol. QC - quick charging using Qualcomm Quick Charge 2.0, Quick Charge 3.0 and Quick Charge 4+ protocols. PPS - quick charging using Programmable Power Supply protocol (part of USB PD 3.0 and QC4+). PD - quick charging using USB Power Delivery 2.0 and Power Delivery 3.0 protocol. Examples of supported phones, tablets and laptops: SFC - quick charging (up to 25W) of Samsung Galaxy S20, S21, S22, S23, S24 series, Note 10, 20 series, Z Fold 2, 3, 4 series. SFC 2.0 - quick charging (up to 45W) of Samsung Galaxy S20, S21, S22, S23, S24 Ultra, Tab S7+, Tab S8+, Tab S9+, Tab S8 Ultra, Tab S9 Ultra. PD - quick charging of Apple iPhone 8, 8 Plus, X, XS, XS Max, XR, 11, 11 Pro, 11 Pro Max phone. PD - quick charging (up to 20W) Apple iPhone 12, 12 Mini, 12 Pro, 12 Pro Max, 12, 12 Mini, 12 Pro, 12 Pro Max, 13, 13 Mini, 14, 14 Plus, 15, 15 Plus phone. PD - quick charging (up to 27W) Apple iPhone 13 Pro, 13 Pro Max, 14 Pro, 14 Pro Max, 15 Pro, 15 Pro Max phone. PD - quick charging (up to 65W) of Lenovo, HP, Dell, Acer, Asus, Apple MacBook Air, MacBook Pro, iPad mini, iPad Air, iPad Pro and others notebooks. The charger supports WIV, AIC and CC functions: Wide Input Voltage - function of a wide range of input voltage; it protects the adapter against undervoltage and overvoltage at the input and allows the use of more national power standards. Automatic Intelligent Communication - function of automatic recognition of the connected device to select optimal charging parameters. Constant Output Current - the current hold function prevents the output power fluctuations; this function ensures steady course of charging. Complex output protection: OCP, OVP, OTP, OSP: Over Current Protection. Protection of output against current overload. Over Voltage Protection. Protection against overvoltage at the output. Over Temperature Protection. Protection against overheating of the adapter. Output Short Circuit protection. Short circuit protection at the output. Other features: dimensions of the charger body 103 x 36 x 32mm including a plug, weight: 118 g, material: non-flammable plastic. Package contains: white wall charger, multilingual guide CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA, packed in a cardboard box with a hanging hole.

The compact USB wallcharger AXAGON ACU-PD30 Silfor fast charging of mobile devices. With s maximum power of 30W, the charger charges phones, tablets and other mobile devices at the highest possible speed. The adapter offers a reversible USB-C connector. Compact size and high performance is given by the new Sil technology used. Super silicon uses advanced silicon-based materials. The charger can thus achieve smaller dimensions and at the same time safe, stable and fast charging. The efficiency is thus identical to GaN technology while maintaining a favorable price. The charger is equipped with Power Delivery 3.0 / Quick Charge 4+ USB Type-C, enabling fast charging of smartphones and tablets with a power of up to 30W. The charger supports 20W PD charging for iPhone 12, 13, 14 and 15 and also offers 27W PD charging for iPhone 13 Pro, 14 Pro, 15 Pro and their Pro Max models. In addition, it supports 25W SFC charging for Samsung Galaxy S20 - S24, Note and Z Fold series and also offers 30W SFC charging for Samsung Galaxy S20 - S24 Ultra, Tab S7+ - S9+, Tab S8 - S9 Ultra. The adapter is also compatible with other fast phone charging standards such as Apple iPhone, iPad, Samsung, Huawei, Honor, Xiaomi. The advanced protection system at the charging adapter output protects the device being charged from damage. The charger function also detects the device being charged and selects the optimal charging speed and progress. The body of the power adapter has a pleasant shape and size. Compared to classic charging adapters with same parameters, the size of the charger is a third smaller. The combination of small dimensions, achieved with Sil technology and a wide range of input voltages, makes the charger an ideal travel helper. Input: input voltage AC 100V-240V / 1A / 50-60 Hz (WIV function) supports multiple national power standards two-pin euro plug - integrated in the body of the charger Output: USB-C port PD (tablets, phones) max. 30W: 5V/3A, 9V/3A, 12V/2.5A, 15V/2A, 20V/1.5A, PPS: 3-11V/3A, 3-16V/2A Charging technology: PD 3.0, PD 2.0, PPS, QC4+, QC 3.0, QC 2.0, SFC, AFC, FCP, SMART, Apple PD, Apple 2.4A Maximum power: maximum power 30W maximum current 3A Supported charging technologies: Standard charging of all devices that support 5V and Apple iPhone 5, 6, SE, 7 charging. SMART - charging max. 5V/3A, Quick Charge 1.0, USB Battery Charging 1.2 (DCP 1.5A) a Apple 2.4A (iPad). FCP - quick charging using Huawei Fast Charge Protocol. AFC - quick charging using Samsung Adaptive Fast Charging protocol. SFC - quick charging using the Samsung Super Fast Charging protocol. QC - quick charging using Qualcomm Quick Charge 2.0, Quick Charge 3.0 and Quick Charge 4+ protocols. PPS - quick charging using the Programmable Power Supply protocol (part of USB PD 3.0 and QC4+). PD - quick charging using USB Power Delivery 2.0 and Power Delivery 3.0 protocol. Examples of supported phones, tablets and ultrabooks: SFC - quick charging (up to 25W) of Samsung Galaxy S20, S21, S22, S23, S24 series, Note 10, 20 series, Z Fold 2, 3, 4 series. SFC - quick charging (up to 30W) of Samsung Galaxy S20, S21, S22, S23, S24 Ultra, Tab S7+, Tab S8+, Tab S9+, Tab S8 Ultra, Tab S9 Ultra. PD - quick charging of Apple iPhone 8, 8 Plus, X, XS, XS Max, XR, 11, 11 Pro, 11 Pro Max phone. PD - quick charging (up to 20W) Apple iPhone 12, 12 Mini, 12 Pro, 12 Pro Max, 12, 12 Mini, 12 Pro, 12 Pro Max, 13, 13 Mini, 14, 14 Plus, 15, 15 Plus phone. PD - quick charging (up to 27W) Apple iPhone 13 Pro, 13 Pro Max, 14 Pro, 14 Pro Max, 15 Pro, 15 Pro Max phone. PD - quick charging (up to 30W) Apple iPad mini, iPad Air, iPad Pro, MacBook Air and other ultrabooks. The charger supports WIV, AIC and CC functions: Wide Input Voltage - function of a wide range of input voltage; it protects the adapter against undervoltage and overvoltage at the input and allows the use of more national power standards. Automatic Intelligent Communication - function of automatic recognition of the connected device to select optimal charging parameters. Constant Output Current - the current hold function prevents the output power fluctuations; this function ensures steady course of charging. Complex output protection: OCP, OVP, OTP, OSP: Over Current Protection. Protection of output against current overload. Over Voltage Protection. Protection against overvoltage at the output. Over Temperature Protection. Protection against overheating of the adapter. Output Short Circuit protection. Short circuit protection at the output. Other features: dimensions of the charger body 84 x 36 x 32 mm including a plug, weight: 56 g, material: non-flammable plastic. Package contains: black wall charger, multilingual guide CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA, packed in a cardboard box with a hanging hole.

The compact USB wallcharger AXAGON ACU-PD30W Sil for fast charging of mobile devices. With s maximum power of 30W, the charger charges phones, tablets and other mobile devices at the highest possible speed. The adapter offers a reversible USB-C connector. Compact size and high performance is given by the new Sil technology used. Super silicon uses advanced silicon-based materials. The charger can thus achieve smaller dimensions and at the same time safe, stable and fast charging. The efficiency is thus identical to GaN technology while maintaining a favorable price. The charger is equipped with Power Delivery 3.0 / Quick Charge 4+ USB Type-C, enabling fast charging of smartphones and tablets with a power of up to 30W. The charger supports 20W PD charging for iPhone 12, 13, 14 and 15 and also offers 27W PD charging for iPhone 13 Pro, 14 Pro, 15 Pro and their Pro Max models. In addition, it supports 25W SFC charging for Samsung Galaxy S20 - S24, Note and Z Fold series and also offers 30W SFC charging for Samsung Galaxy S20 - S24 Ultra, Tab S7+ - S9+, Tab S8 - S9 Ultra. The adapter is also compatible with other fast phone charging standards such as Apple iPhone, iPad, Samsung, Huawei, Honor, Xiaomi. The advanced protection system at the charging adapter output protects the device being charged from damage. The charger function also detects the device being charged and selects the optimal charging speed and progress. The body of the power adapter has a pleasant shape and size. Compared to classic charging adapters with same parameters, the size of the charger is a third smaller. The combination of small dimensions, achieved with Sil technology and a wide range of input voltages, makes the charger an ideal travel helper. Input: input voltage AC 100V-240V / 1A / 50-60 Hz (WIV function) supports multiple national power standards two-pin euro plug - integrated in the body of the charger Output: USB-C port PD (tablets, phones) max. 30W: 5V/3A, 9V/3A, 12V/2.5A, 15V/2A, 20V/1.5A, PPS: 3-11V/3A, 3-16V/2A Charging technology: PD 3.0, PD 2.0, PPS, QC4+, QC 3.0, QC 2.0, SFC, AFC, FCP, SMART, Apple PD, Apple 2.4A Maximum power: maximum power 30W maximum current 3A Supported charging technologies: Standard charging of all devices that support 5V and Apple iPhone 5, 6, SE, 7 charging. SMART - charging max. 5V/3A, Quick Charge 1.0, USB Battery Charging 1.2 (DCP 1.5A) a Apple 2.4A (iPad). FCP - quick charging using Huawei Fast Charge Protocol. AFC - quick charging using Samsung Adaptive Fast Charging protocol. SFC - quick charging using the Samsung Super Fast Charging protocol. QC - quick charging using Qualcomm Quick Charge 2.0, Quick Charge 3.0 and Quick Charge 4+ protocols. PPS - quick charging using the Programmable Power Supply protocol (part of USB PD 3.0 and QC4+). PD - quick charging using USB Power Delivery 2.0 and Power Delivery 3.0 protocol. Examples of supported phones, tablets and ultrabooks: SFC - quick charging (up to 25W) of Samsung Galaxy S20, S21, S22, S23, S24 series, Note 10, 20 series, Z Fold 2, 3, 4 series. SFC - quick charging (up to 30W) of Samsung Galaxy S20, S21, S22, S23, S24 Ultra, Tab S7+, Tab S8+, Tab S9+, Tab S8 Ultra, Tab S9 Ultra. PD - quick charging of Apple iPhone 8, 8 Plus, X, XS, XS Max, XR, 11, 11 Pro, 11 Pro Max phone. PD - quick charging (up to 20W) Apple iPhone 12, 12 Mini, 12 Pro, 12 Pro Max, 12, 12 Mini, 12 Pro, 12 Pro Max, 13, 13 Mini, 14, 14 Plus, 15, 15 Plus phone. PD - quick charging (up to 27W) Apple iPhone 13 Pro, 13 Pro Max, 14 Pro, 14 Pro Max, 15 Pro, 15 Pro Max phone. PD - quick charging (up to 30W) Apple iPad mini, iPad Air, iPad Pro, MacBook Air and other ultrabooks. The charger supports WIV, AIC and CC functions: Wide Input Voltage - function of a wide range of input voltage; it protects the adapter against undervoltage and overvoltage at the input and allows the use of more national power standards. Automatic Intelligent Communication - function of automatic recognition of the connected device to select optimal charging parameters. Constant Output Current - the current hold function prevents the output power fluctuations; this function ensures steady course of charging. Complex output protection: OCP, OVP, OTP, OSP: Over Current Protection. Protection of output against current overload. Over Voltage Protection. Protection against overvoltage at the output. Over Temperature Protection. Protection against overheating of the adapter. Output Short Circuit protection. Short circuit protection at the output. Other features: dimensions of the charger body 84 x 36 x 32 mm including a plug, weight: 56 g, material: non-flammable plastic. Package contains: white wall charger, multilingual guide CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA, packed in a cardboard box with a hanging hole.

The AXAGON ADE-25R external network card easily converts a USB-A 3.2 Gen 1 (USB 3.0) port into a 2.5 Gigabit Ethernet port. It is compatible with 10/100/1000/2500 Mbit/s transfer speeds. The 2.5 Gb/s network adapter expands your computer with an ultra-fast and stable network connection, adds a missing RJ-45 network connector, provides an additional network card, or replaces a non-functional original network connection. Besides 2.5 gigabit throughput, the LAN adapter offers a wide range of features, such as IPv4/IPv6 checksum offloading to reduce CPU load, crossover detection and auto-correction, TCP large send offload, support for various Wake-on-LAN modes, operation with virtual LAN (VLAN), and advanced Power Management features. Thanks to the IEEE 802.3bz standard, standard Cat 5e and Cat 6 Ethernet cables up to 100 m can be used for 2.5 Gb/s speeds. The metal adapter casing is made of aluminum, ensuring excellent mechanical protection and superior heat dissipation. Its compact size and minimal weight make it an ideal accessory for laptops. With support for current versions of Windows, macOS, and Linux, it can be used with any desktop, laptop, or ultrabook. With modern operating systems from Windows 8.1 and newer, the adapter supports easy automatic installation without requiring an internet connection. Input: 1x USB 3.2 Gen 1 / SuperSpeed USB port, USB-A male connector. Backward compatible with USB 3.1 Gen 1 / USB 3.0 and USB 2.0. Supports transmission rates of 5,000 / 480 / 12 / 1.5 Mb/s (SuperSpeed / High / Full / Low speed). Features a USB type A male connector on a 15 cm permanently attached cable. Output: Gigabit Ethernet interface with RJ-45 connector for UTP or STP cable. Supported Ethernet interface transmission rates: 10/100/1000/2500 Mb/s. Supports IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T, and IEEE 802.3bz 2.5GBase-T specifications. 10/100/1000/2500 Mb/s auto-detection. NBASE-T specification support—allows up to 2.5 Gbps over standard UTP Cat5e cables. Supports IPv4/IPv6 packet Checksum Offload Engine (COE) to reduce processor load, including IPv4 IP/TCP/UDP/ICMP/IGMP & IPv6 TCP/UDP/ICMPv6 checksum verification and generation. Supports TCP Large Send Offload V1 and V2. Supports IEEE 802.1P Layer 2 priority encoding & decoding. Supports IEEE 802.1Q VLAN tagging. Supports IEEE 802.3az EEE (Energy Efficient Ethernet) to reduce power consumption during idle. Supports Jumbo frame. Supports full-duplex transmissions with IEEE 802.3x flow control and half-duplex with back-pressure flow control. Supports Auto MDI/MDIX—crossover detection and auto-correction eliminates need for crossover cables. Supports hardware Cyclic Redundancy Check (CRC) for transmission error detection. Supports Pair Swap/Polarity/Skew Correction. Other features: Full Plug and Play and Hot Plug support. Supports CDC-ECM for automatic driver installation on various operating systems. Adapter powered via USB (bus power)—no external power needed. Two LEDs indicate network activity and adapter connection. Dimensions: 64 x 24 x 14 mm. Weight: 26 g (including cable). USB cable length: 15 cm. Features Realtek RTL8156B chipset. Wake-on-LAN feature support in different modes: Supports sleep mode and remote wake-up via Magic Packet, Microsoft Wakeup Frame, Microsoft Wake Packet Detection, and Link Change Wake-up. Supports ECMA-393 proxZzzy standard for sleeping hosts to manage the network connection of sleeping guests using proxy servers. RealWoW! technology support enables remote wake-up over the Internet. Advanced Power Management features: The adapter supports advanced power management to reduce loss during standby or under light network traffic, as well as advanced power saving when the Ethernet cable is disconnected. Supports Advanced Configuration Power Management Interface (ACPI). Supports Power Management offload (ARP & NS). Supports Microsoft Always On Always Connected (AOAC). Supports Intel Converged Platform Power Management (CPPM). Supports Link Power Management (LPM). Supports Operating System-directed Power Management (OSPM). Supports IEEE 802.3az EEE (Energy Efficient Ethernet). Supported OS: MS Windows 7 / 8 / 8.1 / 10 / 11 and later, Windows Server 2008 / 2012 / 2016 / 2019 / 2022 and later (all 32 and 64-bit versions supported), MacOS X 10.6 and later, Linux with kernel 2.6.14 and later. Package includes: 2.5 Gigabit Ethernet adapter with fixed 15 cm USB-A cable, printed installation manual in CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA, packed in a cardboard box with hanging hole.

The AXAGON ADSA-CC CLONE MASTER 2 universal USB-C 10Gbps adapter connects up to two drives to your computer quickly and easily at the same time. Easily connect any 2.5" or 3.5" drive directly to the adapter's external SATA connector. Simply insert the NVMe M.2 drive into the adapter body without the use of a screwdriver or other tools. You can also connect a SATA M.2 drive to the adapter using an external adapter such as the AXAGON RSS-M2SD. In the package you will find a USB-C USB-C cable with a fixed USB-C -> USB-A reduction. This solution enhances the versatility of the adapter, so you can connect it to any USB port on your computer, whether it's a double-sided USB-C connector or a traditional USB-A connector. Thanks to the cloning function without the need to connect to a PC, the adapter can be used as a stand-alone device for convenient duplication and disk imaging. The cloning direction is adjustable via a switch, so you can easily choose whether to clone the contents of an NVMe M.2 drive to a SATA drive or vice versa. After all the data is copied, the target disk is an exact copy of the original disk. This is the easiest way to transfer the contents of one drive to another, including a working operating system (Windows, macOS, Linux ...). In addition to the fast USB 10Gbps interface, the adapter also supports all important functions for working seamlessly with different types of drives, such as UASP for faster data transfer, TRIM for limiting the gradual degradation of SSD performance over time, S.M.A.R.T. for monitoring the status of the drives, BOOT for the ability to boot from drives connected to the adapter, Auto Spindown to automatically put drives to sleep during prolonged inactivity, Turn Off to shut down the drives after removing the device or putting the PC to sleep, and USB Bus Power to power the adapter including connected M.2 and 2.5" drives only from the USB port. In case of connecting a 3.5" drive, the included power adapter is of course already required. These features make the CLONE MASTER 2 adapter a very handy and useful tool for frequent work with different types of drives. This makes it an ideal helper for backup, migration, data transfer and storage, testing and cloning discs, etc. Input: USB 10Gbps (USB 3.2 Gen 2). Speed up to 10 Gbit/s. Connection via reversible USB type C female connector. M.2 slot device support: NVMe (PCI-Express) M.2 SSD one-sided and double-sided drives. Support of M.2 drives with a size of 2242, 2260, 2280 mm. Supports M-KEY & B+M-KEY NVMe M.2 SSD disks. No capacity limitation. Support for devices connected to the SATA port: SATA 2.5"/3.5" SSD/HDD. SATA M.2 SSD with M.2 -> SATA reduction e.g. AXAGON RSS-M2SD. No capacity limitation. Disk cloning feature: Cloning takes place without connecting the station to a computer. The target disk must have the same or larger capacity as the source disk, otherwise cloning cannot be started. Cloning direction switch - from NVMe M.2 drive to SATA drive or from SATA drive to NVME M.2 drive. SSD cloning speed up to 500 MB/s. The total disk cloning time depends on the capacity of the source disk, not the amount of disk data. Other features: Compatible with USB 10Gbps (USB 3.2 Gen 2). Backward compatible with USB 5Gbps (3.2 Gen 1 / USB 3.0) and USB 480Mbps (USB 2.0). Supports transmission rates 10.000 / 5.000 / 480 Mbit/s. Compliant with PCI Express Base Specification Revision 3.1a specification. Compliant with NVM Express 1.3c Specification. The total adapter bandwidth / transmission rate is determined by the USB 3.2 Gen 2 interface used (theoretically up to 10 Gbit/s). The real adapter bandwidth / transmission rate is about 1.000 MB/s (1 GB/s), it is given by the limits of the USB 3.2 Gen 2 interface. Compliant with Serial ATA 3.0 specification (SATA/600), transmission rates of up to 6 Gb/s (600 MB/s). Compliant with Serial ATA 2.0 specification (SATA/300), transmission rates of up to 3 Gb/s (300 MB/s). Compliant with Serial ATA 1.0 specification (SATA/150), transmission rates of up to 1.5 Gb/s (150 MB/s). Compliant with USB Mass Storage Class specification. Supports UASP (USB Attached SCSI) for faster data transmission in Windows 8.1 and later. Supports TRIM functionality to limit gradual degradation of the SSD performance over time. Supports S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) system monitoring disk condition. Support for booting from disks connected to the adapter. HDD Auto Spindown - automatic spinning down when they idle for 10 minutes. HDD Turn Off - turns off the drive after removing the device or spinning down the PC. Full Plug and Play support. Connection via USB-C female connector. Cable USB-C male USB-C male 30 cm length + USB-C -> USB-A reducer included. Adapter dimensions 102 x 68 x 15 mm. Adapter weight 73 g (without accessories). Power: USB Bus Power - for M.2 and 2.5" drives, power via the USB bus is sufficient. Self Power - for 3.5" drives, power is required using the included external AC/DC adapter 12V - 2A with a 150 cm cable. Power switch. LED indication: the green LED indicates that the adapter is powered on (permanent light). 2x orange LED indicates connection for each of the disks (permanent light) and data transmission (blinking). 4x blue LED indicates cloning process 25% -50% -75% -100% (blinking), resp. cloning completion (permanent light). Supported OS: Windows 8.1 / 10 / 11 and later, Windows Server 2012 R2 / 2016 / 2019 / 2022 and later, Mac OS X 10.x and higher, Linux with kernel 2.6.x and higher. Package contains: M.2 + 2.5"/3.5" SSD/HDD adapter, power adapter 100-240V / 12V-2A, 4 thermal conductive pads, USB-C USB-C cable 30 cm long + USB-C -> USB-A reduction, multilingual manual CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA, packed in a cardboard box.

SuperSpeed USB-C 5Gbps docking / cloning station AXAGON ADSA-DC DUAL CLONE easily and quickly connects up to two 2.5" or 3.5" drives to the computer at the same time. The connection to the computer is enabled by the modern double-sided USB-C connector on the dock together with the supplied USB-C USB-A cable with a length of 80 cm. This handy helper will allow you easiest connection of any 2.5/3.5" SATA drive to computer or notebook. Just insert one or even two disks into the base at the same time, no tools or accessories are needed. Changing disks is very quick and easy. You can use the docking station to easy cloning the contents of connected disks without the need to connect to a PC. Insert the source disk into the first slot of the station HDD A (source) and insert the target disk into the second slot HDD B (target). Then you just press the clone button and watch the cloning process on a scale of four LEDs. After all the data has been copied, there is an exact copy of the original disk on the destination disk. The dock can thus be used as an autonomous device for convenient duplication and disk image creation. This is the easiest way to transfer the contents of old HDD to new SSD, including a working operating system (Windows, macOS, Linux...). SATA 6G interface with UASP support allows you to enjoy the speed of modern SSD disks. The TRIM feature support limits the gradual degradation of SSD performance over time. Reading of S.M.A.R.T. information monitoring the SSD/HDD condition. Supports sleeping of the connected disks and station. The station case is sufficiently robust and durable, which allows perfect stability even with inserted disks. Rubber anti-slip pads prevent sliding on the table and vibrations of the hard drives. The outer casing is made of aluminum with an elegant brushed surface. Input: USB-C 5Gbps (USB 3.2 Gen 1 / USB 3.0). Speed up to 5Gbit/s. Connection via USB-C female connector. Device support: SATA III - 6 Gb/s (600 MB/s) interface, Supports 2.5" HDD/ SSD Supports 3.5" HDD. Max. disk capacity all without limitation. Max. 2.5" disk height - all without limitation. Features: Compatible with USB 3.2 Gen 2 (USB 3.1 Gen 2) and backward compatible with USB 2.0. Supports transmission rates 5000 / 480 Mbit/s. Compliant with Serial ATA 3.0 specification (SATA/600), transmission rates of up to 6 Gb/s (600 MB/s). Compliant with Serial ATA 2.0 specification (SATA/300), transmission rates of up to 3 Gb/s (300 MB/s). Compliant with Serial ATA 1.0 specification (SATA/150), transmission rates of up to 1.5 Gb/s (150 MB/s). Compliant with USB Mass Storage Class Specification. The total bandwidth / transmission rate of the station is determined by the USB interface used (theor. 5 Gbit/s). Supports BOT (Bulk-Only Transport). Supports UASP (USB Attached SCSI Protocol) for faster data transmission in Windows 8 and later. TRIM support to reduce the gradual degradation of SSD performance over time. Supports S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) system monitoring disk condition. HDD/SSD boot support in docking station. Possibility to connect your device while running thanks to the Hot Plug support. Full Plug and Play support. HDD Auto Spin down - shutdown of disks when idle. HDD Turn Off - turns off the drive after removing the device or spinning down the PC. Connection via USB-C female connector. USB-C USB-A cable 80 cm long is included. LED indicating HDD/SSD dock power and disk activity in both shafts. Station dimensions 73 x 130 x 97 mm. Weight 307 g. Power: Power supply using the included external AC/DC adapter 12V - 3A with 150 cm long cable. Power switch. Disk cloning feature: Cloning takes place without connecting the station to a computer. The target disk must have the same or larger capacity as the source disk, otherwise cloning cannot be started. Both HDDs and SSDs can be cloned. Cloning speed up to 300 MB/s. The total disk cloning time depends on the capacity of the source disk, not the amount of disk data. Supported OS: Windows, macOS, Linux, Chrome OS. Package contains: HDD/SSD dock, USB-C USB-A cable 80 cm long, power adapter 100-240V / 12V-2.5A, multilingual manual CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA, packed in a cardboard box.

Compact AXAGON ADSA-FP2A SLIM adapter with USB-A 5Gbps and SATA 6G interface for 2.5" SATA hard drives or SSDs. The connection to the computer enables a permanently attached USB-A cable 20 cm long. Thanks to the USB 3.2 Gen 1 interface, the transfer rate is up to 5 Gb/s, and the Plug & Play function ensures automatic connection to the computer. The adapter also supports all important functions for working seamlessly with different types of drives. Such as UASP for faster data transfer, TRIM for limiting the gradual degradation of SSD performance over time, S.M.A.R.T. for monitoring the status of the drives, BOOT for the ability to boot from drives connected to the adapter, Auto Spindown to automatically put drives to sleep during prolonged inactivity, Turn Off to shut down the drives after removing the device or putting the PC to sleep, and USB Bus Power to power the adapter including connected drives only from the USB port. The slim and compact adapter enables easy and quick disc replacement without the need for assembly, and at the same time, thanks to its minimal dimensions, it can be readily at hand at any time. The matte design of the cover prevents unwanted fingerprints. These features make the adapter a very handy and useful tool for frequent work with different types of drives. This makes it an ideal tool for backup, migration, data transfer, storage and recovery, discs testing, etc. Input: USB-A 5Gbps (USB 3.2 Gen 1 / USB 3.0). Speed up to 5 Gbit/s. Connection via USB type A male connector. Device support: SATA III - 6Gb/s (600 MB/s) interface, Supports 2.5" SSD/HDD, max. disk capacity - all without limit. Other features: Compatible with USB 5Gbps (USB 3.2 Gen 1 / USB 3.0). Backward compatible with USB 480Mbps (USB 2.0). Supports transmission rates 5.000 / 480 Mbit/s. Compliant with Serial ATA 3.0 specification (SATA/600), transmission rates of up to 6 Gb/s (600 MB/s). Compliant with Serial ATA 2.0 specification (SATA/300), transmission rates of up to 3 Gb/s (300 MB/s). Compliant with Serial ATA 1.0 specification (SATA/150), transmission rates of up to 1.5 Gb/s (150 MB/s). The total bandwidth / transmission rate of the adapter is determined by the USB interface (theor. 5 Gbit/s). Supports BOT (Bulk-Only Transport). Supports UASP (USB Attached SCSI Protocol). Supports TRIM functionality to limit gradual degradation of the SSD performance over time. Supports S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) system monitoring disk condition. Supports booting from SSD/HDD connected via an USB adapter. HDD Auto Spindown - automatic spindown of a disk after period of inactivity lasting 10 minutes. HDD Turn Off - turns off the disk after removing the device or spinning down the PC. Possibility to connect your device while running thanks to the Hot Plug support. Full Plug and Play support. Connection via USB-C male connector on 20 cm long cable permanently connected to the adapter. Supplying the power via bus up to 900mA from one USB port is sufficient in all cases. Decently bright LED indicating the connection of USB power supply (permanent light) and data transmission (blinking). Adapter dimensions 70 x 26 x 10 mm. Adapter weight only 20 g incl. USB cable. Supported OS: Windows 7 / 8.1 / 10 / 11 a and later, Windows Server 2008 R2 / 2012 R2 / 2016 / 2019 / 2022 and later, Mac OS X 10.x and higher, Linux with kernel 2.6.x and higher. Package contains: USB-A - SATA adapter with permanently connected 20 cm long cable, multilingual guide CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA, packed in a cardboard box.

Compact AXAGON ADSA-FP2C SLIM adapter with USB-C 5Gbps and SATA 6G interface for 2.5" SATA hard drives or SSDs. The connection to the computer enables a permanently attached USB-C cable 20 cm long. Thanks to the USB 3.2 Gen 1 interface, the transfer rate is up to 5 Gb/s, and the Plug & Play function ensures automatic connection to the computer. The adapter also supports all important functions for working seamlessly with different types of drives. Such as UASP for faster data transfer, TRIM for limiting the gradual degradation of SSD performance over time, S.M.A.R.T. for monitoring the status of the drives, BOOT for the ability to boot from drives connected to the adapter, Auto Spindown to automatically put drives to sleep during prolonged inactivity, Turn Off to shut down the drives after removing the device or putting the PC to sleep, and USB Bus Power to power the adapter including connected drives only from the USB port. The slim and compact adapter enables easy and quick disc replacement without the need for assembly, and at the same time, thanks to its minimal dimensions, it can be readily at hand at any time. The matte design of the cover prevents unwanted fingerprints. These features make the adapter a very handy and useful tool for frequent work with different types of drives. This makes it an ideal tool for backup, migration, data transfer, storage and recovery, discs testing, etc. Input: USB-C 5Gbps (USB 3.2 Gen 1 / USB 3.0). Speed up to 5 Gbit/s. Connection via USB type C male connector. Device support: SATA III - 6Gb/s (600 MB/s) interface, Supports 2.5" SSD/HDD, max. disk capacity - all without limit. Other features: Compatible with USB 5Gbps (USB 3.2 Gen 1 / USB 3.0). Backward compatible with USB 480Mbps (USB 2.0). Supports transmission rates 5.000 / 480 Mbit/s. Compliant with Serial ATA 3.0 specification (SATA/600), transmission rates of up to 6 Gb/s (600 MB/s). Compliant with Serial ATA 2.0 specification (SATA/300), transmission rates of up to 3 Gb/s (300 MB/s). Compliant with Serial ATA 1.0 specification (SATA/150), transmission rates of up to 1.5 Gb/s (150 MB/s). The total bandwidth / transmission rate of the adapter is determined by the USB interface (theor. 5 Gbit/s). Supports BOT (Bulk-Only Transport). Supports UASP (USB Attached SCSI Protocol). Supports TRIM functionality to limit gradual degradation of the SSD performance over time. Supports S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) system monitoring disk condition. Supports booting from SSD/HDD connected via an USB adapter. HDD Auto Spindown - automatic spindown of a disk after period of inactivity lasting 10 minutes. HDD Turn Off - turns off the disk after removing the device or spinning down the PC. Possibility to connect your device while running thanks to the Hot Plug support. Full Plug and Play support. Connection via USB-C male connector on 20 cm long cable permanently connected to the adapter. Supplying the power via bus up to 900mA from one USB port is sufficient in all cases. Decently bright LED indicating the connection of USB power supply (permanent light) and data transmission (blinking). Adapter dimensions 70 x 26 x 10 mm. Adapter weight only 18 g incl. USB cable. Supported OS: Windows 7 / 8.1 / 10 / 11 a and later, Windows Server 2008 R2 / 2012 R2 / 2016 / 2019 / 2022 and later, Mac OS X 10.x and higher, Linux with kernel 2.6.x and higher. Package contains: USB-C - SATA adapter with permanently connected 20 cm long cable, multilingual guide CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA, packed in a cardboard box.

SuperSpeed USB AXAGON ADSA-SN COMPACT HDD/SSD DOCK docking station easily and quickly connects any SATA disk to your computer. A handy helper for the easiest and fastest way of connecting SATA disks to your computer - just plug the disk into the base. Automatic installation can be done even by the layman. SATA 6G interface with UASP support allows you to enjoy the speed of modern SSD disks. The TRIM feature support limits the gradual degradation of SSD performance over time. Reading of S.M.A.R.T. information monitoring the condition of the connected disks. Supports sleeping of both the connected disks and station. Low laid centre of gravity of the docking station for good stability. Rubber feet to reduce vibrations. Modern minimalist design of housing with aluminium casing. Input: USB 3.2 Gen 1 (USB 3.1 Gen 1 / USB 3.0) SuperSpeed USB rate of up to 5 Gbit/s. Connection via micro USB type B female connector. Device support: SATA III - 6 Gb/s (600 MB/s) interface, supports 2.5" HDD/SSD, supports 3.5" HDD, max. disk capacity all without limitation, max. 2.5" disk height- all without limitation. Other features: Compatible with USB 3.2 Gen 1 / USB 3.1 Gen 1 / USB 3.0, backward compatible with USB 2.0. Supports transmission rates 5000 / 480 Mbit/s (SuperSpeed / HighSpeed). Compliant with Serial ATA 3.0 specification (SATA/600), transmission rates of up to 6 Gb/s (600 MB/s). Compliant with Serial ATA 2.0 specification (SATA/300), transmission rates of up to 3 Gb/s (300 MB/s). Compliant with Serial ATA 1.0 specification (SATA/150), transmission rates of up to 1.5 Gb/s (150 MB/s). The total bandwidth / transmission rate of the station is determined by the USB interface used (theor. 5 Gbit/s). Supports UASP (USB Attached SCSI Protocol) and BOT (Bulk-Only Transport). SSD/HDD boot support in docking station. Possibility to connect your device while running thanks to the Hot Plug support. Full Plug and Play support. HDD Auto Spindown - automatic spinning down after period of inactivity lasting 15 minutes. HDD Turn Off - turns off the drive after removing the device or spinning down the PC. cable micro USB-B / USB-A 80 cm long is included. A decent blue LED indicating the connection to the computer's USB port (permanent light) and data transmission (blinking). Power switch. Power supply via a compact external AC/DC adapter 12V - 2A (24 W) with a 150 cm long supply cable. Station dimensions 130 x 65 x 59 mm. Weight 190 g. Supported OSs: MS Windows XP / Vista / 7 / 8 / 8.1 / 10 and later, Windows Server 2008 / 2012 / 2016 and later (supported are all 32- and 64-bit Windows OS versions), Mac OS X 10.x and higher, Linux with kernel 2.6.x and above.Note: Drivers are included with supported operating systems and are installed completely automatically. No other drivers need to be installed and are not even available. Package contains: USB 3.2 Gen 1 HDD dock, micro USB-B - USB-A cable 80 cm long, power adapter 100-240V / 12V-2A, multilingual manual CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA, packed in a cardboard box with clearly indicated parameters.

SuperSpeed USB 5 Gbps docking / cloning station AXAGON ADSA-ST DUAL station quickly and easily connects up to two SATA disk to your computer at the same time. The USB-B connector on the dock together with the supplied USB-B USB-A cable enables a connection to computer. This handy helper allows you to connect SATA disks to your computer or notebook in the easiest way. No need for mounting as with an external box, just slide one or even two disks into the base at the same time. Technicians will also appreciate the fast disk replacement. SATA 6G interface with UASP support allows you to enjoy the speed of modern SSD disks. The TRIM feature support to reduce gradual degradation of SSD performance over time. Reading S.M.A.R.T. information monitoring the condition of the connected disks. Sleep support of attached drives and station. Easy and fast attached disk content cloning without the need for a PC connection. The HDD dock can be used as an autonomous device for convenient duplication and disk image creation. This is the easiest way to transfer the contents of old disk to new SSD, including a working operating system (Windows, macOS, Linux...). SSD cloning speed up to 300 MB/s. The station case is sufficiently robust and durable, which allows perfect stability even with inserted disks. Rubber pads reduce vibration of hard drives. The outer case is made of aluminum with an elegant brushed surface. Input: USB 3.2 Gen 1 (USB 3.1 Gen 1 / USB 3.0) SuperSpeed USB 5 Gbps. Speed up to 5 Gbit/s. Connection via USB type B SuperSpeed female connector. Device support: SATA III - 6 Gb/s (600 MB/s) interface, supports 2.5" SSD/HDD, supports 3.5" HDD, max. disk capacity - all without restriction, max. 2.5" disk height- all without limitation. Features: Compatible with USB 3.2 Gen 2 / USB 3.1 Gen 1 (USB 3.0), backward compatible with USB 2.0. Supports transmission rates 5000 / 480 Mbit/s (SuperSpeed / HighSpeed). Compliant with Serial ATA 3.0 specification (SATA/600), transmission rates of up to 6 Gb/s (600 MB/s). Compliant with Serial ATA 2.0 specification (SATA/300), transmission rates of up to 3 Gb/s (300 MB/s). Compliant with Serial ATA 1.0 specification (SATA/150), transmission rates of up to 1.5 Gb/s (150 MB/s). The total bandwidth / transmission rate of the station is determined by the USB 3.2 Gen1 interface used (theor. 5 Gbit/s). Supports UASP (USB Attached SCSI Protocol) and BOT (Bulk-Only Transport). Supports TRIM functionality to limit gradual degradation of the SSD performance over time. Supports S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) system monitoring disk condition. SSD/HDD boot support in docking station. Possibility to connect your device while running thanks to the Hot Plug support. Full Plug and Play support. HDD Auto Spin down - shutdown of disks when idle. HDD Turn Off - turns off the drive after removing the device or spinning down the PC. Connection via durable large USB 3.2 Gen 1 type B female connector. USB 3.2 Gen 1 type A male / type B female cable length 70 cm included. 3x LED indicating SSD/HDD dock power and disk activity in both shafts. Station dimensions 142 x 102 x 80 mm. Weight 330 g. Power: Power supply using the included external AC/DC adapter 12V 2.5A (30W) with 150 cm long cable. Power switch. Disk cloning feature: Cloning takes place without connecting the station to a computer. The target disk must have the same or larger capacity as the source disk, otherwise cloning cannot be started. Both HDD and SSD can be cloned. Cloning starts by pressing and holding the CLONE button for minimally 3 seconds. 4 LEDs indicate the progress and completion of cloning. SSD cloning speed up to 300 MB/s. The total disk cloning time depends on the capacity of the source disk, not the amount of disk data. Supported OS: MS Windows 7 / 8 / 10 / 11 and later, Windows Server 2008 / 2012 / 2016 / 2019 / 2022 and later (all 32-bit and 64-bit Windows OS versions are supported), Mac OS X 10.x and higher, Linux with kernel 2.6.x and higher. Note: Drivers are included with supported operating systems and are installed completely automatically. No other drivers need to be installed and are not even available. Package contains: SSD/HDD dock, USB-B USB-A cable, 70 cm long, power adapter 100-240V / 12V-2.5A, multilingual manual CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA, packed in a cardboard box.

The external network card AXAGON ADE-25RC easily converts USB-C 3.2 Gen 1 (USB 3.0) port to 2.5 Gigabit Ethernet port. It is compatible with 10/100/1000/2500 Mbit/s transfer speeds. The network adapter with 2.5 Gb/s speed expands the computer with a very fast and stable network connection, adds the missing RJ-45 network connector, adds another network card, or replaces the original non-functional network connection. In addition to 2.5 gigabit throughput, the LAN adapter offers a wide range of features, such as IPv4/IPv6 checksum to reduce CPU load by checksums, the crossover detection and auto-correction, TCP large send offload, support for various modes of the Wake-on-LAN feature, the work with virtual LAN (VLAN) and advanced Power Management features. The advantage of the IEEE 802.3bz standard is that standard Cat 5e and Cat 6 Ethernet cables up to 100 m long can be used for 2.5 Gb/s speed. The metal adapter cover is made of aluminum and provides perfect mechanical protection and excellent heat dissipation. Thanks to its compact dimensions and minimal weight, it is an ideal accessory for laptops. The support for current versions of Windows, macOS, and Linux operating systems allows it to be used for any desktop, laptop or ultrabook equipped with a modern double-sided USB Type C connector. In modern operating systems from Windows 8.1 above, the adapter allows easy automatic installation without the need for an Internet connection. Input: 1x USB 3.2 Gen 1 / SuperSpeed USB port, USB-C male connector. Backward compatible with USB 3.1 Gen 1 / USB 3.0 and USB 2.0. Compatible with Thunderbolt 3 and 4. Supports transmission rates 5.000 / 480 / 12 / 1.5 Mb/s (SuperSpeed / High / Full / Low speed). Connecting USB type C male connector on a 15 cm long permanently attached cable. Output: Gigabit Ethernet interface with RJ-45 connector for UTP or STP cable connection. Supported transmission rates for the Ethernet interface 10/100/1000/2500 Mb/s. Supported IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T, IEEE 802.3bz 2.5GBase-T specifications. 10/100/1000/2500 Mb/s auto-detection. NBASE-T specification support - allows speeds up to 2.5 Gbps via standard UTP Cat5e cables. Supports IPv4 / IPv6 packet Checksum Offload Engine (COE) to reduce processor load, including IPv4 IP/TCP/UDP/ICMP/ IGMP & IPv6 TCP/UDP/ICMPv6 checksum control and generation. Supports TCP Large Send Offload V1 and V2. Supports IEEE 802.1P Layer 2 priority encoding & decoding. Supports IEEE 802.1Q VLAN tagging. Supports IEEE 802.3az EEE (Energy Efficient Ethernet) - reduce power consumption at rest. Supports Jumbo frame. Supports full-duplex transmissions with IEEE 802.3x flow control and half-duplex transmissions with back-pressure flow control. Supports Auto MDI/MDIX - crossover detection and auto-correction eliminates the need for crossover cables. Supports hardware Cyclic Redundancy Check (CRC) to detect transmission errors. Supports Pair Swap/Polarity/Skew Correction. Other features: Full Plug and Play and Hot Plug support. Supports CDC-ECM for automatic installation of drivers across different OSs. Adapter power supply via USB (bus power) - no auxiliary power supply required. Two LEDs indicate the network activity and connection of the adapter to the network. Dimensions 64 x 24 x 14 mm. Weight 26 g (incl. cable). USB cable length 15 cm. The Realtek RTL8156B chipset is used. Wake-on-LAN feature support in different modes: Supports sleep mode and remote Wake Up via Magic Packet, Microsoft Wakeup Frame, Microsoft Wake Packet Detection and Link Change Wake-up. Supports ECMA-393 proxZzzy standard for sleeping hosts to manage the network connection of sleeping guests using proxy servers. RealWoW! technology support allows remote wake up over the Internet. Advanced Power Management features:The adapter supports advanced power management to reduce losses during standby or light traffic on the network. It further supports advanced power saving when the Ethernet cable has been disconnected. Supports Advanced Configuration Power Management Interface (ACPI). Supports Power Management offload (ARP & NS). Supports Microsoft Always On Always Connected (AOAC). Supports Intel Converged Platform Power Management (CPPM). Supports Link Power Management (LPM). Supports Operating System-directed Power Management (OSPM). Supports IEEE 802.3az EEE (Energy Efficient Ethernet). Supported OS: MS Windows 7 / 8 / 8.1 / 10 / 11 and later, Windows Server 2008 / 2012 / 2016 / 2019 / 2022 and later (supported are all 32 and 64-bit versions of Windows OSs), MacOS X 10.6 and later, Linux with kernel 2.6.14 and later. Package contains: 2.5 Gigabit Ethernet adapter with fixed 15 cm long USB-C cable, printed installation manual in CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA, packed in a cardboard.

A compact AXAGON ADSA-1S6 SLIMport6 high-speed adapter with USB 3.0 and SATA 6G interface intended for easy connection of SSD or 2.5" SATA disk. A handy tool to quickly connect a SSD or laptop disk, including boot support. The UASP support significantly increases transmission rates especially when working with small files in the queue. The TRIM feature support limits the gradual degradation of SSD performance over time. Reading of S.M.A.R.T. information monitoring the condition of the connected disks. Supports spinning down of connected disks as well as an adapter. The installation can be handled even by a layman - the disk connects to the adapter and the adapter to the computer's USB port; the rest is done automatically. Minimum dimensions and weight, along with an enclosed disc case, make the product ideally suited even for mobile use. Features: Compatible with USB 3.0 and backward compatible with USB 2.0. Supports transmission rates 12 / 480 / 5000 Mb/s (low / full / high speed). Supports 2.5" SATA III / II / I disks of all capacities. Compliant with Serial ATA 3.1 specification (SATA/600), transmission rates of up to 6 Gb/s. Compliant with Serial ATA 2.0 specification (SATA/300), transmission rates of up to 3 Gb/s (300 MB/s). Compliant with Serial ATA 1.0 specification (SATA/150), transmission rates of up to 1.5 Gb/s (150 MB/s). The total bandwidth / transmission rate of the adapter is determined by the USB 3.0 interface used (theor. 5 Gbit/s). Supports UASP (USB Attached SCSI Protocol) and BOT (Bulk-Only Transport). Supports booting from SSD/HDD connected via an USB adapter. HDD Auto Spindown - automatic spindown of a disk after period of inactivity lasting 22 minutes. HDD Turn Off - turns off the disk after removing the device or spinning down the PC. Possibility to connect your device while running thanks to the Hot Plug support. Full Plug and Play support. Connection via USB 3.0 micro B female connector. USB 3.0 cable USB 3.0 Type A male / USB 3.0 Type B male 10 cm long is included. Supplying the power via USB 3.0 bus up to 900mA from one USB port is sufficient in all cases. A blue LED indicating the connection to the computer's USB port (permanent light) and data transmission (blinking). Compact adapter dimensions 70 x 21 x 10 mm. Adapter weight only 11 g, weight of USB cable 18 g. Simple plastic case holds 2.5" disk max. 9.5 mm high with USB adapter connected (USB cable is led out through hole in the case). For thin 7mm SSDs/HDDs foam pads are included for better fit in the case. The case can also serve to transport or store the adapter itself without the disk, with the USB cable inside the case. Case dimensions 122 x 78 x 19 mm. Case weight 40 g. Supported OSs: MS Windows XP / Vista / 7 / 8 / 8.1 / 10 and later, Windows Server 2003 / 2008 / 2012 / 2016 and later (supported are all 32- and 64-bit Windows OS versions), Mac OS X 10.x and higher, Linux with kernel 2.6.x and above. Note: Drivers are included with supported operating systems and are installed completely automatically. No other drivers need to be installed and are not even available. Package contains:USB 3.0 - SATA 6G adapter,USB 3.0 cable 10 cm,plastic case for 2.5" disk and USB adapter,foam pads for 7 mm HDDs and SSDs,printed multilingual manual CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA,Packed in a cardboard box.

SuperSpeed USB 5 Gbps docking / cloning station AXAGON ADSA-D25 CLONE MINI quickly and easily connects up to two 2.5" disks to your computer at the same time. The USB Micro-B connector on the dock and included USB Micro-B USB-A cable enables a connection to computer. This compact helper will allow you easiest connection of any 2.5" SATA drive to computer or notebook. Just insert one or two disks into the base at the same time, no tools or accessories are needed. Changing disks is very quick and easy. You can use the docking station to easy cloning the contents of connected disks without the need to connect to a PC. Insert the source disk into the first slot of the station HDD A (source) and insert the target disk into the second slot HDD B (target). Then you just press the clone button and watch the cloning process on a scale of four LEDs. After all the data has been copied, there is an exact copy of the original disk on the destination disk. The dock can thus be used as an autonomous device for convenient duplication and disk image creation. This is the easiest way to transfer the contents of old HDD to new SSD, including a working operating system (Windows, macOS, Linux). SATA 6G interface with UASP support allows you to enjoy the speed of modern SSD disks. The TRIM feature support limits the gradual degradation of SSD performance over time. Reading of S.M.A.R.T. information monitoring the SSD/HDD condition. Supports sleeping of the connected disks and station. The station case is sufficiently robust and durable, which allows perfect stability even with inserted disks. Rubber anti-slip pads prevent sliding on the table and vibrations of the hard drives. The outer casing is made of aluminum with an elegant brushed surface. Input: USB 3.2 Gen 1 (USB 3.1 Gen 1 / USB 3.0) SuperSpeed USB 5 Gbps. Speed up to 5 Gbit/s. Connection via USB Micro-B female connector. Device support: SATA III - 6 Gb/s (600 MB/s) interface. Supports 2.5" SSD/HDD. Max. disk capacity all without limitation. Max. 2.5" disk height- all without limitation. Other features: Compatible with USB 3.2 Gen 2 (USB 3.1 Gen 2), USB 3.2 Gen 1 (USB 3.1 Gen 1 / USB 3.0), backward compatible with USB 2.0. Supports transmission rates 5000 / 480 Mbit/s (SuperSpeed / HighSpeed). Compliant with Serial ATA 3.0 specification (SATA/600), transmission rates of up to 6 Gb/s (600 MB/s). Compliant with Serial ATA 2.0 specification (SATA/300), transmission rates of up to 3 Gb/s (300 MB/s). Compliant with Serial ATA 1.0 specification (SATA/150), transmission rates of up to 1.5 Gb/s (150 MB/s). Compliant with USB Mass Storage Class Specification. The total bandwidth / transmission rate of the station is determined by the USB interface used (theor. 5 Gbit/s). Supports BOT (Bulk-Only Transport). Supports UASP (USB Attached SCSI) for faster data transmission in Windows 8 and later. Supports TRIM functionality to limit gradual degradation of the SSD performance over time. Supports S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) system monitoring disk condition. SSD/HDD boot support in docking station. Possibility to connect your device while running thanks to the Hot Plug support. Full Plug and Play support. HDD Auto Spindown - automatic spinning down when idle. HDD Turn Off - turns off the drive after removing the device or spinning down the PC. Connection via USB Micro-B female connector. USB Micro-B USB-A cable 60 cm long is included. LED indicating SSD/HDD dock power and disk activity in both shafts. Station dimensions 89 x 58 x 59 mm. Weight 137 g. Power: Power cable USB-A 3.5/1.3 mm DC 5V length 1 m is included in the package. The cable allows powering the station from the computer USB-A port or a standard mobile phone charger with a USB-A output of 5V / min. 1A, e.g. AXAGON ACU-DS16. Power switch. Disk cloning feature: Cloning takes place without connecting the station to a computer. The target disk must have the same or larger capacity as the source disk, otherwise cloning cannot be started. Both HDD and SSD can be cloned. Cloning speed up to 300 MB/s. The total disk cloning time depends on the capacity of the source disk, not the amount of disk data. Supported operating systems: MS Windows 7 / 8 / 10 / 11 and later, Windows Server 2008 / 2012 / 2016 / 2019 / 2022 and later (all 32-bit and 64-bit Windows OS versions are supported), Mac OS X 10.x and higher, Linux with kernel 2.6.x and higher. Note: Drivers are included with supported operating systems and are installed completely automatically. No other drivers need to be installed and are not even available. Package contains: SSD/HDD dock, USB Micro-B USB-A cable 60 cm long, power cable 100 cm, printed installation manual CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA, packed in a cardboard box.

Multiport USB-C 3.2 Gen 1 hub AXAGON HMC-HCR3A expands your laptop, computer or phone with four ports and SD / microSD card reader. Through the double-sided USB-C connector, you can easily and quickly connect three USB devices, memory cards and an HDMI display to the computer at the same time. The USB-C hub will provide you with a simple and compact 5in1 docking station for notebook. The USB hub offers three USB outputs with standard USB-A connectors. The hub can also handle permanent connection of several external drives simultaneously. Transfer rate up to 5Gb/s thanks to the fast USB 3.2 Gen 1 interface. The hub will also enable charging of phones and tablets with a current of up to 1.5A/5V, so you can easily charge e.g. Android smartphone, Apple iPhone, Apple iPad etc. HDMI output provides high quality image up to 4K/30Hz Ultra HD resolution and supports multi-channel audio transmission. Popular gaming resolution WQHD 2560 x 1440px at 60Hz or FullHD 1920 x 1080px at 60, 100 and 120Hz max. are also supported. DisplayPort Alternate Mode (DP Alt Mode) enabled USB-C port or Thunderbolt 3 port is necessary for the proper function of video output. Card reader supports all current versions of SD and microSD cards including SDXC and microSDXC with capacity up to 2TB. High data transfer speed ensured by USB 3.2 Gen 1 interface. The card reader enables simultaneous handling of cards in both slots and direct copying between them. Elegant aluminum body ensures mechanical resistance and quality cooling. The finely structured surface with no fingerprint remains will also please you. Port replicator is an ideal accessory for laptops without USB-A connectors, card reader and video output. You can use your current USB peripherals without having to purchase new ones. Thanks to the Plug and Play and Hot Plug functions, connecting the hub itself is very simple without complicated installation, and peripherals can also be easily connected and disconnected while the computer is running. The hub does not afraid of connection to phones with a USB-C connector. You can connect a flash drive, keyboard, mouse, monitor, TV or projector to your phone. Input: 1x USB 3.2 Gen 1 / SuperSpeed USB port, USB-C male connector. Backward compatible with USB 3.1 Gen 1 / USB 3.0 and USB 2.0. Compatible with Thunderbolt 3. Connecting USB type C male connector on a fixed 20 cm long cable. USB outputs: 3x SuperSpeed USB port, USB-A female connector. Supports transmission rates 5.000 / 480 / 12 / 1.5 Mb/s (SuperSpeed / High / Full / Low speed). The total bandwidth / transmission rate of the box is determined by the USB 3.2 Gen 1 interface used (theoretically up to 5 Gbit/s). USB-C hub can handle the connection of several external drives at the same time. Charging of mobile devices (including iPad) with a current of up to 1.5A in each of the hub's USB ports. The total charging current (which is divided into ports) reaches up to 3A at 5V (depending on the capabilities of the computer's USB port). HDMI output: HDMI. HDMI A (F) female connector. Maximum supported resolution 4K / 4096 x 2160 at 30 Hz. WQHD resolution 2560 x 1440 at 60 Hz max. FullHD resolution 1920 x 1080 at 60, 100, 120 Hz max. DisplayPort Alternate Mode (DP Alt Mode) enabled USB-C port or Thunderbolt 3 port is necessary for the proper function of video output. Correct OS is also necessary. The video output function will not be available without these requirements. HPD (Hot-Plug-Detect) support. TMDS (Transition Minimized Differential Signalling) support. HDCP 1.4 and 2.3 (High-bandwidth Digital Content Protection) support. Support up to 8-channel LPCM audio, compressed audio (AC-3, DTS) and HBR audio formats. Support sampling rate up to 192kHz and up to 24-bit audio depends on source and end device, i.e. laptop/phone and TV/monitor/ AV receiver. The card reader - two slots: Micro SD slot: microSD / microSDHC / microSDXC / TransFlash, SD slot: Digital / SDHC / SDXC, MultiMedia Card, MMC 4.0, MMC Dual Voltage, MMC mobile, RS-MMC, with adapter miniSD, microSD / microSDHC / microSDXC, MMC Micro. The reader supports the following flash card specifications: SD 1.0/1.1 (SD - Secure Digital, up to 2GB). SD 2.0 (SDHC - Secure Digital High Capacity, up to 32GB). SD 3.0 (SDXC - Secure Digital eXtended Capacity, up to 2TB), MMC and eMMC 3.x /4.0 / 4.1 / 4.2 / 4.3 / 4.4 / 4.5 / 5.0 (8-bit). Supports SD 3.01 and SD Jukebox applications (CPRM functions). Supports Ultra High Speed bus UHS-I (SDR12/SDR25/SDR50/DDR50/SDR104) speeds up to 104 MB/s. Supports hardware ECC (Error Correction Code) function and CRC (Cyclic Redundancy Check) function. 2 LUN - the reader is indicated as two disk drives in the file manager. Other features: Possibility to connect your device while running thanks to the Hot Plug support. Full Plug and Play support. Standby mode support. Power supply via USB bus (USB bus power). Heavy-duty aluminium body for better hub cooling. Higher surface hub temperature is not a problem - the heat generated by the hub operation is better dissipated and transferred to the surroundings. White LED indicates the connection to the computer's USB port. The high quality shielded cable ensures high communication speed and minimal undesirable interference. Dimensions 110 x 35 x 12.5 mm. Weight 58 g (incl. cable). USB cable length 20 cm. Supported operating systems: Microsoft Windows 10, 11, Mac OS, Linux, Android and Chrome OS. Compatibility depends on used OS and support from device manufacturer. Note 1: Drivers are included with supported operating systems and are installed automatically. No other drivers need to be installed. Note 2: DisplayPort Alternate Mode (DP Alt Mode) is only supported in updated OS and also depends on support from device (notebook, phone) manufacturer. Package contains: USB-C hub with fixed 20 cm long cable, multilingual manual CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / BG / CN / TR / ARA, packed in a cardboard box with a hanging hole.

AXAGON PCEU-43RS PCI-Express card adds four external USB 3.2 Gen 1 ports to your desktop computer. The card is designed for fast data transfers at speeds up to 5 Gb/s. All four SuperSpeed USB ports are taken out to the bracket. The dual power supply of the controller enables standard power supply of the controller and connected USB peripherals via the PCI-Express bus as well as optional power supply from the PC power supply via the SATA power connector. The USB controller is equipped with a renowned Renesas company chipset with proven seamless compatibility, high performance and UASP support. Low profile bracket is included in the package for mounting the adapter into low profile cases. Input: PCI-Express 2.0 interface, compatible with PCI-Express 1.0a / 1.1 / 2.1 / 3.0. Number of lines: 1-Lane (x1), compatible with x1 / x4 / x8 / x16 PCIe slots. A bandwidth of 1-Lane PCI-Express 2.0 bus is 5 Gb/s. Output: 4x external USB 3.2 Gen 1 port with USB type A-F connectors. SuperSpeed USB - USB 3.2 Gen 1 interface (before USB 3.1 Gen 1 / USB 3.0). Compatible with USB 3.2 Gen 2, backward compatible with USB 2.0 a USB 1.1. Supports transmission rates 5000 / 480 / 12 / 1.5 Mb/s (super / high / full / low speed). When connected to a PCI-Express bus version 1.0, theor. transmission rate max. 2500 Mb/s. Other features: Full Plug and Play support. Supports concurrent activity of SuperSpeed USB, USB 2.0 and USB 1.1 devices. Compliant with the final official xHCI specification revision 1.0 by USB-IF. Supports UASP (USB Attached SCSI) for faster data transmission in Windows 8 and later. Fully supports Hot Plug connecting and disconnecting of USB devices while running. Standard power supply for the controller and connected USB peripherals via the PCI-Express bus. In this power supply mode, the PCIe controller can handle up to three magnetic 2.5" external disks simultaneously. Optional power supply from PC source via SATA power connector. Renesas PD720201 chipset is used. Supported operating systems: MS Windows XP / Vista / 7 / 8 / 8.1 / 10 / 11 and later, Windows Server 2003 / 2008 / 2012 / 2016 / 2019 / 2022 and later (supported are all 32- and 64-bit Windows OS versions), Linux with kernel 2.6.31 and above. Note: Drivers are only installed for Windows XP / Vista / 7. For Linux, Windows 8 / 8.1 / 10 / 11, Server 2012 / 2016 / 2019 / 2022 and later versions, no external drivers are required, they are already part of the operating system. Package contains: PCI-Express controller with a standard bracket, low-profile bracket multilingual guide CZ / DE / DK / ENG / ESP / FIN / FR / GR / HR / HU / IT / NL / PL / PT / RO / RU / SK / SWE / TR / BG / CN / ARA, packed in a cardboard box.

• 5 Gbit/s • Materjal: Alumiinium • Varunduse meedia tüüp: HDD, SSD • Ketta liides: Jada ATA, Jada ATA II, Jada ATA III • Toetatud ketaste suurused: 2.5,3.5" • Hostiliides: USB 3.2 Gen 1 (3.1 Gen 1) Type-A • DC-pistik Isehäälestuv • Hall Axagon AXG ADSA-DC - Docking- und Kopierstation 2x 2.5"/3.5" SATA USB 3.0 - Digital/Daten, HDD, SSD, Jada ATA, Jada ATA II, Jada ATA III, 2.5,3.5", USB 3.2 Gen 1 (3.1 Gen 1) Type-A, Hall, Alumiinium

Premium connection USB-C USB-C Data and Charging AXAGON BUCM2-CM25AB CHARGE cable with USB-C male connectors at both ends. The cable is designed especially for charging and powering computers, monitors, laptops, phones, tablets and other devices. It also supports data transfer speeds of up to 480 Mb/s. The cable has implemented the latest specification of Power Delivery 3.1 charging technology. This technology delivers, among other things, a power output of 240W which is more than double that of Power delivery 3.0, which delivers 100W. You can use not only the (Standard Power Range SPR) for voltages of 5, 9, 15 and 20V with a current of 5A, but also sufficient power in fixed voltages of 28, 36 and 48V with a maximum current of 5A (Extended Power Range - EPR). Thanks to the new PD 3.1 technology, you can also use the cable to power devices with much more power, such as gaming laptops, 4K monitors, power tools or the increasingly popular e-scooters. To identify the cable and its current capabilities, the cable has an integrated E-Mark chip. The cable is also compatible with Quick Charge, PPS, Samsung AFC and SFC, Apple, SMART and other charging technologies. Durable, extended-life bidirectional cable features metal terminals, nickel-plated connectors and gold-plated contacts. Cable conductors are made of Tin-plated oxygen free copper. High-quality cable insulation, made of flexible TPE, guarantees maximum durability and also maintains sufficient flexibility. The final strength of the cable is provided by the nylon braid. The bonus is a practical strip for easy packing of the cable. Power cables 22AWG (lower number = larger cross-section and lower wire resistance) guarantee fast charging of phones and other mobile devices. Data wires 30AWG together with high-quality shielding, ensure reliable data transmission. Double shielding protects transmitted signals from adverse interference. Nylon braid in combination with a cable gland significantly reduces dangerous cable bending. The cable life is extended to more than 8000 standard bends. The mechanical resistance of the cable is also increased by the aluminum terminal covers. Connectors: 2x USB-C (M) male. Other features: DATA SYNC & FAST CHARGING - simultaneous data transfer and charging of the connected device. USB 480Mbps (USB 2.0), compatible with USB 1.1. Supports 480 / 12 / 1.5 Mb/s transmission rates. Supported charging technologies: Power Delivery 2.0/3.0/3.1 - 240W (48V/5A), Qualcomm Quick Charge 2.0 / 3.0 / 4+, PPS, Samsung Adaptive Fast Charging and Super Fast Charging, Huawei Fast Charge Protocol, Apple Fast Charging, SMART Charging and others. Support Extended Power Range (EPR) specification up to 240W and Standard Power Range (SPR) specification up to 100W. Support for fast charging with a current of up to 5A. Integrated E-MARK chip. Cable includes power wires 22AWG, data wires 30AWG. Tin-plated oxygen free copper conductors to reduce oxidation, increase conductivity, and clear signal without distortion. Shielding via galvanized foil and oxygen free copper braiding minimizes interference and prevents signal loss. Nickel-plated connectors and gold-plated contacts prevent oxidation and provide a reliable connection. Suitable for computers, laptops, mobile phones, tablets, power banks, power tools and other devices with USB-C connector. Other data: cable length 2.5 m, 4.6 mm outer diameter of the cable. Package contains: USB-C M USB-C M black cable, tightening strip, packed in a printed and sealed foil package with hanging hole.