Kõik hinnakirjad

GST3D PLA SILK 1.75mm 1kg GRAPHITE 3D filament – läikiv tumehall 3D materjal Pappkarp puudub (tuleb ainult vaakumpakendis) Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

GST3D PLA SILK 1.75mm 1kg Green 3D filament – läikiv roheline 3D materjal Pappkarp puudub (tuleb ainult vaakumpakendis) Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

GST3D PLA SILK 1.75mm 1kg Peach 3D filament – läikiv roosa 3D materjal Pappkarp puudub (tuleb ainult vaakumpakendis) Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

GST3D PLA SILK 1.75mm 1kg Purple 3D filament – läikiv lilla 3D materjal Pappkarp puudub (tuleb ainult vaakumpakendis) Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

GST3D PLA SILK 1.75mm 1kg Red 3D filament – läikiv punane 3D materjal Pappkarp puudub (tuleb ainult vaakumpakendis) Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

GST3D PLA SILK 1.75mm 1kg Sand 3D filament – läikiv kuldne/pruun 3D materjal Pappkarp puudub (tuleb ainult vaakumpakendis) Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

GST3D PLA+ 1.75mm 1kg Bright Blue 3D filament – sädelev sinine 3D materjal Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

GST3D PLA+ 1.75mm 1kg Bright Green 3D filament – sädelev roheline 3D materjal Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

GST3D PLA+ 1.75mm 1kg Bright Red 3D filament – sädelev punane 3D materjal Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

GST3D PLA+ 1.75mm 1kg Bright Silver 3D filament – sädelev hõbe 3D materjal Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

GST3D PLA+ 1.75mm 1kg Fluorescent Green 3D filament – pimedas helendav roheline 3D materjal Pappkarp puudub (tuleb ainult vaakumpakendis) Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

GST3D PLA+ 1.75mm 1kg Fuchsia 3D filament Pappkarp puudub (tuleb ainult vaakumpakendis) Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

GST3D PLA+ 1.75mm 1kg Ice Blue 3D filament Pappkarp puudub (tuleb ainult vaakumpakendis) Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

GST3D PLA+ 1.75mm 1kg Light Blue 3D filament Pappkarp puudub (tuleb ainult vaakumpakendis) Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

GST3D PLA+ 1.75mm 1kg Light Pink 3D filament Pappkarp puudub (tuleb ainult vaakumpakendis) Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

GST3D PLA+ 1.75mm 1kg Marble 3D filament Pappkarp puudub (tuleb ainult vaakumpakendis) Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

GST3D PLA+ 1.75mm 1kg Mellow Yellow 3D filament Pappkarp puudub (tuleb ainult vaakumpakendis) Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

GST3D PLA+ 1.75mm 1kg Metallic Bronze 3D filament Pappkarp puudub (tuleb ainult vaakumpakendis) Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

GST3D PLA+ 1.75mm 1kg Mustard 3D filament Pappkarp puudub (tuleb ainult vaakumpakendis) Tehnilised andmed: Kaal: 1KG/Spool Diameeter: 1.75MM Printimise temperatuur: 180-220℃ Soojendatava aluse temperatuur: Ilma soojenduseta / 40-60℃

Produkta veids: 3D printeru izejmateriāli, Materiāla diametrs: 1.75 mm, Drukas diega tips: PLA, Garantija: 2 gadi

Schneller 3D-Druck, beeindruckende Ergebnisse: Das Hyper PLA RFID von Creality überzeugt mit seiner hochfließfähigen und schnell abkühlenden Formel. Die hohe Fließfähigkeit sorgt für ausreichendes Schmelzen und Extrusion während die schnelle Abkühlung eine schnelle Formgebung für den Hochgeschwindigkeitsdruck ermöglicht. So unterstützt dieses 3D-Filament Druckgeschwindigkeiten von bis zu 600 mm/s - mit hoher Präzision und Ergebnissen, die sich durch eine gute strukturelle Tragfähigkeit auszeichnen. Hyper PLA RFID ist in verschiedenen Farben erhältlich. Diese Rolle enthält 1 Kilogramm Filament in der Farbe orange.

Thanks to the high fluidity and fast cooling formula, Hyper Series PLA supports up to 600mm/s print speed. High fluidity provides sufficient melting and extrusion, while rapid cooling provides fast shaping for high-speed printing. Easy filament identification for Creality printers and CFS deices with RFID identification option High Precision High stability ensures small changes in thermal expansion and cold contraction even when printing at high speeds, bringing high precision in dimensions and better results. Higher Toughness With higher tensile strength than ABS and higher toughness than traditional PLA, Hyper Series PLA brings better structural bearing capacity to the printed models. Application: Prototyping Figurines Machine parts Mass production Specifications: Wire diameter: 1.75±0.03mm Density 1.25g/cm3 Tensile strenght (X-Y) 52.991 Mpa Tensile modulus (X-Y) 1146.064 Elogation at break 6.3% Bending streght (X-Y) 92.3Mpa Printing temperatue 190-230 ºC Printing speed 30-600mm/s

Thanks to the high fluidity and fast cooling formula, Hyper Series PLA supports up to 600mm/s print speed. High fluidity provides sufficient melting and extrusion, while rapid cooling provides fast shaping for high-speed printing. Easy filament identification for Creality printers and CFS deices with RFID identification option High Precision High stability ensures small changes in thermal expansion and cold contraction even when printing at high speeds, bringing high precision in dimensions and better results. Higher Toughness With higher tensile strength than ABS and higher toughness than traditional PLA, Hyper Series PLA brings better structural bearing capacity to the printed models. Application: Prototyping Figurines Machine parts Mass production Specifications: Wire diameter: 1.75±0.03mm Density 1.25g/cm3 Tensile strenght (X-Y) 52.991 Mpa Tensile modulus (X-Y) 1146.064 Elogation at break 6.3% Bending streght (X-Y) 92.3Mpa Printing temperatue 190-230 ºC Printing speed 30-600mm/s

Thanks to the high fluidity and fast cooling formula, Hyper Series PLA supports up to 600mm/s print speed. High fluidity provides sufficient melting and extrusion, while rapid cooling provides fast shaping for high-speed printing. Easy filament identification for Creality printers and CFS deices with RFID identification option High Precision High stability ensures small changes in thermal expansion and cold contraction even when printing at high speeds, bringing high precision in dimensions and better results. Higher Toughness With higher tensile strength than ABS and higher toughness than traditional PLA, Hyper Series PLA brings better structural bearing capacity to the printed models. Application: Prototyping Figurines Machine parts Mass production Specifications: Wire diameter: 1.75±0.03mm Density 1.25g/cm3 Tensile strenght (X-Y) 52.991 Mpa Tensile modulus (X-Y) 1146.064 Elogation at break 6.3% Bending streght (X-Y) 92.3Mpa Printing temperatue 190-230 ºC Printing speed 30-600mm/s

<h3>Longer LK10 3D Printer</h3> <p>The Longer LK10 is a 3D printer designed for fast and convenient project completion. It offers a build volume of 225 × 225 × 265 mm, print speeds of up to 500 mm/s, and a Direct Drive extruder with a flow rate of up to 25 mm³/s. A nozzle reaching 300°C and a heated bed up to 110°C allow for the use of PLA, PETG, ABS, ASA, and TPU filaments. Automatic leveling, Auto Z-Offset, filament end detection, and resume-on-power-loss features make operation more convenient. Wi-Fi, LAN, and USB connectivity, along with compatibility with Windows and Mac, allow for convenient print management.</p> <p> (image) </p><h3>Fast Direct Drive Extruder</h3> <p>The printer is equipped with a Direct Drive extruder featuring a precision gear mechanism that ensures smooth material feed even during high-speed printing. The High-Flow Hotend system achieves a volumetric flow rate of up to 25 mm³/s, allowing for high-quality models even with more demanding projects. A maximum print speed of up to 500 mm/s results in shorter print times without sacrificing detail.</p> <p> (image) </p><h3>Less vibration and ghosting</h3> <p>The Klipper software, featuring the Vibration Calibration function, ensures smooth operation of the device. Input Shaping technology reduces ghosting and wall waviness, ensuring models maintain high accuracy even at high speeds. This solution results in a more aesthetically pleasing appearance of prints and greater detail consistency.</p> <p> (image) </p><h3>Wide range of supported materials</h3> <p>A nozzle temperature of up to 300°C and a heated build plate reaching 110°C allow for printing with many popular 1.75 mm filaments. The printer supports PLA, PETG, ABS, ASA, and TPU, making it suitable for both simple decorative models and more durable functional parts. The adjustable layer height from 0.1 to 0.4 mm allows you to tailor print quality and speed to a specific project.</p> <p> (image) </p><h3>Automatic Calibration</h3> <p>The LK10 features automatic leveling of the heated build plate and an Auto Z-Offset function that automatically sets the correct distance between the nozzle and the build surface. This solution reduces the need for manual configuration and allows you to start printing faster. The “load filament, click print, and walk away” operation system makes the device convenient even for less advanced users.</p> <p> (image) </p><h3>Sensorless Homing</h3> <p>The printer uses a Sensorless Homing system that performs X and Y axis homing without the use of traditional mechanical limit switches. Stepper motors detect resistance and automatically determine the axis position, which simplifies the device’s design and reduces the number of wear-prone components. This solution also contributes to more stable operation of the entire system.</p> <p> (image) </p><h3>Safe Printing</h3> <p>The power-outage resume feature allows printing to continue from the last saved layer, reducing the risk of losing hours of work. The filament end sensor monitors material flow in real time and stops printing when an empty spool is detected. The Object Exclusion feature allows you to cancel the printing of a single defective model without interrupting work on the remaining items on the build plate.</p> <p> (image) </p><h3>Easy operation and connectivity</h3> <p>An intuitive, multilingual touchscreen simplifies daily operation and provides quick access to settings. The printer supports Wi-Fi, LAN, and USB flash drive connectivity, allowing you to conveniently transfer files and manage prints in various ways. Compatibility with Windows and Mac systems, along with support for STL, OBJ, and STEP formats, enables convenient model preparation in popular software and the OrcaSlicer slicer.</p> <p> (image) </p><h3>Metal construction</h3> <p>The metal frame increases structural rigidity and reduces vibrations during high-speed printing, which positively impacts print quality. The printer measures 423 × 437 × 492 mm and weighs 8.3 kg, offering a large workspace while maintaining a compact form factor for placement on a desk, in a studio, or in a workshop.</p> <p> (image) </p><h3>Dual Z-axis</h3> <p>A dual Z-axis system with two independent motors and trapezoidal screws ensures smooth head movement. This solution improves print precision, enhances dimensional repeatability of models, and reduces the risk of the X-axis arm sagging during prolonged operation.<br /></p> <p> (image) </p> <h3>Kit Contents</h3> <ul class="list-disc pl-5"><li>Gantry frame profile</li><li>Base unit</li><li>Touchscreen</li><li>Filament holder</li><li>Power cable</li><li>Test filament</li><li>Flathead screwdriver</li><li>Allen wrenches</li><li>USB flash drive (U-Disk)</li><li>Zip ties</li><li>M5x45 screws (4 pieces)</li><li>M4x20 screws (4 pieces)</li><li>M3x6 screws (2 pieces)</li></ul> <div class="table-wrapper"> <p> </p> <h3></h3> <table> <tbody> <tr><th>Manufacturer</th><td>Longer</td></tr><tr><th>Model</th><td>LK10</td></tr><tr><th>Printing technology</th><td>FDM</td></tr><tr><th>Build volume</th><td>225x225x265 mm</td></tr><tr><th>Maximum print speed</th><td>Up to 500 mm/s</td></tr><tr><th>Print accuracy</th><td>100±0.1 mm</td></tr><tr><th>Layer thickness</th><td>0.1-0.4 mm</td></tr><tr><th>Nozzle diameter</th><td>0.4 mm</td></tr><tr><th>Number of nozzles</th><td>1</td></tr><tr><th>Extruder type</th><td>Direct Drive Extruder Head High-Flow Hotend</td></tr><tr><th>Maximum volumetric flow rate</th><td>Up to 25 mm³/s</td></tr><tr><th>Maximum nozzle temperature</th><td>Up to 300°C</td></tr><tr><th>Maximum bed temperature</th><td>Up to 110°C</td></tr><tr><th>Filament diameter</th><td>1.75 mm</td></tr><tr><th>Supported materials</th><td>PLA, PETG, ABS, ASA, TPU, etc.</td></tr><tr><th>Firmware</th><td>Klipper</td></tr><tr><th>Vibration reduction feature</th><td>Vibration Calibration</td></tr><tr><th>Bed leveling</th><td>Automatic</td></tr><tr><th>Nozzle distance adjustment</th><td>Auto Z-Offset</td></tr><tr><th>Axis homing</th><td>Sensorless Homing for X and Y axes</td></tr><tr><th>Resume after power loss</th><td>Power-off resume</td></tr><tr><th>Filament end sensor</th><td>Filament break detection</td></tr><tr><th>Object exclusion</th><td>Object exclusion (up to 32 parts on a single platform)</td></tr><tr><th>Z-axis configuration</th><td>Dual Z-axis</td></tr><tr><th>User interface</th><td>Touchscreen</td></tr><tr><th>Connectivity</th><td>USB Drive, LAN, Wi-Fi</td></tr><tr><th>Default slicer</th><td>OrcaSlicer</td></tr><tr><th>Supported file formats</th><td>STL, OBJ, STEP</td></tr><tr><th>Compatible operating systems</th><td>Windows, MAC, etc.</td></tr><tr><th>Menu languages</th><td>Simplified Chinese, Traditional Chinese, English, German, Italian, Japanese, French, Portuguese, Spanish</td></tr><tr><th>Power Supply</th><td>100-120V/220-240V, 50/60 Hz (manual voltage selector switch for AC 115V / 230V; default 230V)</td></tr><tr><th>Operating environment</th><td>Temperature: 5°C–40°C (optimal 25°C), Humidity: 20%–50%</td></tr><tr><th>Safety requirements</th><td>The device must be grounded during operation</td></tr><tr><th>Frame construction</th><td>Metal construction</td></tr><tr><th>Printing platform</th><td>Gold PEI plate</td></tr><tr><th>Printer dimensions</th><td>423x437x492 mm</td></tr><tr><th>Package dimensions</th><td>515x495x280 mm</td></tr><tr><th>Device weight</th><td>8.3 kg</td></tr><tr><th>Weight with packaging</th><td>11.5 kg</td></tr> </tbody> </table> </div>

<h3>Longer LK10 Plus 3D Printer</h3> <p>The Longer LK10 Plus is a 3D printer designed for fast and convenient project completion. It offers a build volume of 320 × 320 × 400 mm, print speeds of up to 500 mm/s, and a Direct Drive extruder with a flow rate of up to 25 mm³/s. A nozzle reaching 300°C and a heated bed up to 110°C allow for the use of PLA, PETG, ABS, ASA, and TPU filaments. Automatic leveling, Auto Z-Offset, filament end detection, and resume-on-power-loss features make operation more convenient. Wi-Fi, LAN, and USB connectivity, along with compatibility with Windows and Mac, allow for convenient print management.</p> <p> (image) </p><h3>Fast Direct Drive Extruder</h3> <p>The printer is equipped with a Direct Drive extruder featuring a precision gear mechanism that ensures smooth material feeding even during high-speed printing. The High-Flow Hotend system achieves a volumetric flow rate of up to 25 mm³/s, allowing for high-quality models even with more demanding projects. A maximum print speed of up to 500 mm/s results in shorter print times without sacrificing detail.</p> <p> (image) </p><h3>Less vibration and ghosting</h3> <p>The Klipper software, featuring the Vibration Calibration function, ensures smooth operation of the device. Input Shaping technology reduces ghosting and wall waviness, ensuring models maintain high accuracy even at high speeds. This solution results in a more aesthetically pleasing appearance of prints and greater detail consistency.</p> <p> (image) </p><h3>Wide range of supported materials</h3> <p>A nozzle temperature of up to 300°C and a heated build plate reaching 110°C allow for printing with many popular 1.75 mm filaments. The printer supports PLA, PETG, ABS, ASA, and TPU, making it suitable for both simple decorative models and more durable functional parts. The adjustable layer height from 0.1 to 0.4 mm allows you to tailor the print quality and speed to a specific project.</p> <p> (image) </p><h3>Automatic Calibration</h3> <p>The LK10 Plus features automatic leveling of the heated build plate and an Auto Z-Offset function that automatically sets the correct distance between the nozzle and the build surface. This solution reduces the need for manual configuration and allows you to start printing faster. The “load filament, click print, and walk away” operation system makes the device convenient even for less advanced users.</p> <p> (image) </p><h3>Sensorless Homing</h3> <p>The printer uses a Sensorless Homing system that performs X and Y axis homing without the use of traditional mechanical limit switches. Stepper motors detect resistance and automatically determine the axis position, which simplifies the device’s design and reduces the number of wear-prone components. This solution also contributes to more stable operation of the entire system.</p> <p> (image) </p><h3>Safe Printing</h3> <p>The power-outage resume feature allows printing to continue from the last saved layer, reducing the risk of losing hours of work. The filament end sensor monitors material flow in real time and stops printing when an empty spool is detected. The Object Exclusion feature allows you to cancel the printing of a single defective model without interrupting work on the remaining parts on the build plate.</p> <p> (image) </p><h3>Easy operation and connectivity</h3> <p>An intuitive, multilingual touchscreen simplifies daily operation and provides quick access to settings. The printer supports Wi-Fi, LAN, and USB flash drive connections, allowing you to conveniently transfer files and manage prints in various ways. Compatibility with Windows and Mac systems, along with support for STL, OBJ, and STEP formats, enables convenient model preparation in popular software and the OrcaSlicer slicer.</p> <p> (image) </p><h3>Metal Construction</h3> <p>The metal frame increases structural rigidity and reduces vibrations during high-speed printing, which positively impacts print quality. The printer offers a large build volume of 320 × 320 × 400 mm, making it suitable for larger models and printing multiple parts simultaneously.</p> <p> (image) </p><h3>Dual Z-axis</h3> <p>A dual Z-axis system with two independent motors and trapezoidal screws ensures smooth head movement. This solution improves print precision, enhances dimensional repeatability of models, and reduces the risk of the X-axis arm sagging during prolonged operation.</p> <p> (image) </p> <h3>Included in the set</h3> <ul class="list-disc pl-5"><li>Upper frame module</li><li>Base unit</li><li>Touchscreen</li><li>Filament holder</li><li>Power cable</li><li>Test filament</li><li>Flathead screwdriver</li><li>Allen wrenches</li><li>USB flash drive</li><li>Cable ties</li><li>M5x45 screws (4 pieces)</li><li>M4x20 screws (4 pieces)</li><li>M5x20 screws (2 pieces)</li><li>M5x10 screws (2 pieces)</li><li>M3x6 screws (2 pieces)</li><li>Flat washers</li><li>Stabilizing bracket</li></ul> <div class="table-wrapper"> <p> </p> <h3></h3> <table> <tbody> <tr><th>Manufacturer</th><td>Longer</td></tr><tr><th>Model</th><td>LK10 Plus</td></tr><tr><th>Printing technology</th><td>FDM</td></tr><tr><th>Build volume</th><td>320 × 320 × 400 mm</td></tr><tr><th>Frame construction</th><td>Metal, gantry-style structure reinforced with double diagonal stabilizing profiles (braces)</td></tr><tr><th>Build plate</th><td>Gold PEI plate</td></tr><tr><th>Z-axis configuration</th><td>Dual Z-axis (two independent motors and trapezoidal screws)</td></tr><tr><th>Maximum print speed</th><td>Up to 500 mm/s</td></tr><tr><th>Print accuracy</th><td>100±0.1 mm</td></tr><tr><th>Layer thickness</th><td>0.1–0.4 mm</td></tr><tr><th>Nozzle diameter</th><td>0.4 mm</td></tr><tr><th>Number of nozzles</th><td>1</td></tr><tr><th>Extruder type</th><td>Direct Drive Extruder</td></tr><tr><th>High-Flow Hotend</th><td>Maximum volumetric flow rate</td></tr><tr><th>Up to 25 mm³/s</th><td>Maximum nozzle temperature</td></tr><tr><th>Up to 300°C</th><td>Maximum bed temperature</td></tr><tr><th>Up to 110°C</th><td>Filament diameter</td></tr><tr><th>1.75 mm</th><td>Supported materials</td></tr><tr><th>PLA, PETG, ABS, ASA, TPU, etc.</th><td>Firmware</td></tr><tr><th>Klipper</th><td>Vibration reduction feature</td></tr><tr><th>Vibration Calibration</th><td>Bed leveling</td></tr><tr><th>Automatic</th><td>Nozzle offset adjustment</td></tr><tr><th>Auto Z-Offset</th><td>Axis homing</td></tr><tr><th>Sensorless Homing for X and Y axes</th><td>Power-off resume</td></tr><tr><th>Power-off resume</th><td>Filament end sensor</td></tr><tr><th>Filament break detection</th><td>Object exclusion</td></tr><tr><th>Object exclusion (up to 32 parts on a single platform)</th><td>Z-axis configuration</td></tr><tr><th>Dual Z-axis</th><td>User interface</td></tr><tr><th>Touchscreen</th><td>Connectivity</td></tr><tr><th>USB Drive, LAN, Wi-Fi</th><td>Default Slicer</td></tr><tr><th>OrcaSlicer</th><td>Supported file formats</td></tr><tr><th>STL, OBJ, STEP</th><td>Compatible operating systems</td></tr><tr><th>Windows, MAC, etc.</th><td>Menu languages</td></tr><tr><th>Simplified Chinese, Traditional Chinese, English, German, Italian, Japanese, French, Portuguese, Spanish</th><td>Power Supply</td></tr><tr><th>100-120V/220-240V, 50/60 Hz (manual voltage selector switch for AC 115V / 230V; default 230V)</th><td>Operating environment</td></tr><tr><th>Temperature: 5°C–40°C (optimal 25°C), Humidity: 20%–50%</th><td>Safety requirements</td></tr><tr><th>The device must be grounded during operation</th><td>Frame construction</td></tr><tr><th>Metal construction</th><td>Work platform</td></tr><tr><th>Gold PEI plate</th><td>Printer dimensions</td></tr><tr><th>423x437x492 mm</th><td>Package dimensions</td></tr><tr><th>515x495x280 mm</th><td>Device weight</td></tr><tr><th>8.3 kg</th><td>Weight with packaging</td></tr> </tbody> </table> </div>

PETG HF Green (33500) / Filament with spool

PETG HF Orange (33300) / Filament with spool

PETG HF Peanut Brown (33801) / Filament with spool

PETG HF Yellow (33400) / Filament with spool

PLA Anycubic Filament 1 KG (White)Discover PLA Anycubic filament - the perfect combination of precision and environmental care. The carefully wound spool eliminates tangles, and the stable ± 0.02 mm diameter guarantees extremely accurate prints. The biodegradable material, created from lactic acid, is nature-friendly, while the separately available Color Engine Pro intelligent system with RFID (Radio-frequency Identification, a technology for wireless identification of objects using radio waves) will automatically select the optimal print settings, simplifying the entire process and minimizing waste. In addition, semi-transparent CMYK (Cyan, Magenta, Yellow, Black - a set of four primary colors) technology allows you to create full-color, striking 3D models. Give your prints new life and choose Anycubic today!Precision you can count onAnycubic filament features an extremely durable diameter with a tolerance of ± 0.02 mm, which means that every print will be reproduced with the highest accuracy. Details are sharp, surfaces are smooth, and combined with ultra-high color consistency, you'll get excellent aesthetic and mechanical results. Each roll of Anycubic filament has been wound with special care, so you avoid the frustration of tangled filament. Even winding eliminates the risk of jams and print breaks, and the absence of air bubbles guarantees a smooth, uninterrupted 3D printing process.With the environment in mindAnycubic filament is made from lactic acid, obtained during the fermentation of corn starch (or other plants) by wet milling. It is a biodegradable material that is fully nature-friendly.Smart printingThanks to RFID technology, the Anycubic Color Engine Pro system (available outside the kit) automatically recognizes the type of filament and optimizes printer settings. Forget about tedious calibrations, simply load the filament and the printer will adjust the temperature, speed and retraction on its own, minimizing material waste and guaranteeing perfect results on every job. Remember to heat the print head above 230°C before installing or replacing the filament. This will avoid the risk of nozzle clogging and ensure continuous operation. Compatibility with all FDM (Fused Deposition Modeling, belongs to the group of incremental techniques whose characteristic is extrusion of material from print heads) printers available on the market makes PLA Anycubic a versatile and reliable solution for any 3D printing enthusiast.Experiments with translucent CMYKTranslucent CMYK filament uses four primary colors (cyan, magenta, yellow, black) to create as many as one million vibrant hues under light. Overlapping the colors in different ratios produces full-color 3D embossing on printers such as the Kobra 3 Combo, ideal for creating striking transparent models. ManufacturerAnycubicModelIPHPLWH-106ColorWhiteWeight1 kgHardness81DNozzle temperature200-210°C (High speed 3D printer 190-230°C)Tensile strength61 MpaMaterialPLADiameter1.75±0.02mmTotal lengthApproximately 330mHeating table temperature50-60°CDensity1.23/cm³

PLA Basic Bambu Green (10501) / Filament with spool

PLA Basic Blue (10601) / Filament with spool

PLA Basic Indigo Purple (10701) / Filament with spool

PLA Basic Kakaopruun (10802) / Filament koos spooli jaoturiga / 1 kg

PLA Basic Pumpkin Orange (10301) / Filament with spool

PLA Filament 3D-Printeri jaoks

PLA Siid Multi-Värviline Fantoomsinine (13916) / Filament koos rulliga /

Das Creality PLA+ Filament erhöht die Zähigkeit des Baustücks; es kann wiederholt gebogen werden und ist weniger anfällig für Brüche. Die stabilere Druckleistung erfüllt die Bedürfnisse von Heimwerkern, die eine höhere Qualität der Filamente wünschen. Eine präzise Kontrolle des Filamentdurchmessers und automatische EPC-Wickelanordnung sichern einen reibungsloseren Vorschub um einen fehlerfreien Druck zu erlangen.

PLA-CF Burgundy Red (14200) / Filament with spool

PLA-CF Iris Purple (14700) / Filament with spool

PLA-CF Jeans Blue (14600) / Filament with spool

PLA-CF Lava Gray (14101) / Filament with spool

PLA-CF Royal Blue (14601) / Filament with spool

<h3>QIDI Max 4 3D printer</h3> <p>The QIDI Max 4 is an advanced 3D printer designed for large projects and working with demanding materials. The large workspace, high head temperature, and active chamber heating allow you to print both standard filaments and engineering materials. The CoreXY design, fast closed-loop motors, and extensive cooling system ensure that the device works quickly, stably, and precisely.</p> <p> (image) </p><h3>Large workspace</h3> <p>The QIDI Max 4 offers a working area of 390 × 390 × 340 mm. Such a large print volume allows you to create large models in one piece without having to divide the project into smaller parts. This saves you time on assembly and maintains the strength of the finished model.</p> <p> (image) </p><h3>High print head temperature for technical materials</h3> <p>The print head reaches a temperature of up to 370°C, which allows you to work with a wide range of filaments – from PLA and PETG to more demanding materials such as PC or carbon fiber composites. The ceramic throat and improved heat dissipation module reduce the risk of nozzle clogging, keeping printing stable even at high temperatures.</p> <p> (image) </p><h3>Active chamber heating</h3> <p>The third generation of active chamber heating reaches temperatures of up to 65°C. Combined with the air circulation system, this creates a stable environment for printing materials that are prone to deformation. As a result, even large models made of PLA or ABS retain their geometry and do not curl at the edges.</p> <p> (image) </p><h3>Very fast and precise printing</h3> <p>The use of FOC stepper motors in a closed loop increases drive efficiency by up to 65%. The maximum printing speed reaches 800 mm/s, and the acceleration reaches 30,000 mm/s². This configuration significantly reduces project completion time while maintaining high accuracy.</p> <p> (image) </p><h3>Stable CoreXY design</h3> <p>The CoreXY motion system with 10 mm wide 1.5GT belts ensures high rigidity and accuracy of the head guidance. The X-axis uses a high-hardness linear guide, the Y-axis uses 12 mm steel shafts, and the Z-axis uses four guides and two independent motors with trapezoidal screws. This allows the printer to remain stable even with large and heavy models.</p> <p> (image) </p><h3>Automatic leveling and print control</h3> <p>The printer is equipped with automatic table leveling with a load cell sensor integrated into the hot end. The monitoring system includes a filament end sensor, an AI camera, and a print resume function after a power failure. This makes the printing process safer and requires less manual control.</p> <p> (image) </p><h3>Air filtration and convenient operation</h3> <p>The QIDI Max 4 has a 3-stage air filtration system consisting of a G3 pre-filter, HEPA H12 filter, and activated coconut carbon. The printer is also equipped with a 5-inch touch screen, Wi-Fi and Ethernet connectivity, and a 1080p camera for viewing and recording timelapse footage of the printing process.</p> <p> (image) </p> <h3>Included</h3> <ul class="list-disc pl-5"><li>Filament holder with pneumatic head</li><li>Filament spool holder</li><li>Holder cover</li><li>Case door handle</li><li>Spare parts kit</li><li>Mechanism maintenance oil</li><li>7 mm wrench</li><li>Power cord</li><li>Ethernet cable</li><li>USB flash drive with software and files</li><li>Flat screwdriver</li><li>Adhesive for the work surface to improve print adhesion</li><li>Set of Allen keys (H1.27, H1.5, H2, H2.5, H3)</li><li>Scraper for removing prints from the table</li></ul> <div class="table-wrapper"> <p> </p> <h3></h3> <table> <tbody> <tr><th>Manufacturer</th><td>QiDi</td></tr><tr><th>Model</th><td>Max 4</td></tr><tr><th>Working area</th><td>390 × 390 × 340 mm</td></tr><tr><th>Printer dimensions</th><td>558 × 578 × 612 mm</td></tr><tr><th>Weight</th><td>40 kg</td></tr><tr><th>Maximum head temperature</th><td>up to 370°C</td></tr><tr><th>Maximum table temperature</th><td>up to 120°C</td></tr><tr><th>Chamber temperature</th><td>up to 65°C (active heating – 3rd generation)</td></tr><tr><th>Maximum print speed</th><td>800 mm/s</td></tr><tr><th>Maximum acceleration</th><td>30,000 mm/s²</td></tr><tr><th>Extruder</th><td>Direct Drive, hardened steel double gears</td></tr><tr><th>Supported filaments</th><td>PLA, ABS, ASA, PETG, TPU, PA, PC, carbon fiber and glass fiber composites</td></tr><tr><th>Filament diameter</th><td>1.75 mm</td></tr><tr><th>Material flow</th><td>40 mm³/s</td></tr><tr><th>Automatic leveling</th><td>yes (load cell sensor in hotend)</td></tr><tr><th>Filament sensor</th><td>Yes – filament end detection</td></tr><tr><th>Air filter</th><td>3-in-1: G3 + HEPA H12 + activated carbon</td></tr><tr><th>Camera</th><td>1080p with timelapse support</td></tr><tr><th>Connectivity</th><td>Wi-Fi 2.4/5 GHz, Ethernet, USB</td></tr><tr><th>Memory</th><td>32 GB eMMC + USB 2.0</td></tr><tr><th>Screen</th><td>5" touchscreen 800 × 480</td></tr><tr><th>Supported file formats</th><td>STL, OBJ, 3MF, STEP, STP</td></tr><tr><th>Software</th><td>QIDI Studio, OrcaSlicer, PrusaSlicer, and others</td></tr><tr><th>Power supply</th><td>110V / 220–240V AC, 50/60 Hz</td></tr><tr><th>Rated power</th><td>150 W + 500 W (chamber heating) + 700 W (heating table)</td></tr> </tbody> </table> </div>

<h3>QIDI Max 4 Combo 3D printer</h3> <p>QIDI Max 4 is an advanced 3D printer designed for large projects and working with demanding materials. Its large workspace, high head temperature, and active chamber heating allow you to print both standard filaments and engineering materials. The CoreXY design, fast closed-loop motors, and extensive cooling system ensure that the device works quickly, stably, and precisely.</p> <p> (image) </p><h3>Large workspace</h3> <p>The QIDI Max 4 offers a working area of 390 × 390 × 340 mm. Such a large print volume allows you to create large models in one piece without having to divide the project into smaller parts. This saves you time on assembly and maintains the strength of the finished model.</p> <p> (image) </p><h3>High print head temperature for technical materials</h3> <p>The print head reaches a temperature of up to 370°C, which allows you to work with a wide range of filaments – from PLA and PETG to more demanding materials such as PC or carbon fiber composites. The ceramic throat and improved heat dissipation module reduce the risk of nozzle clogging, keeping printing stable even at high temperatures.</p> <p> (image) </p><h3>Active chamber heating</h3> <p>The third generation of active chamber heating reaches temperatures of up to 65°C. Combined with the air circulation system, this creates a stable environment for printing materials that are prone to deformation. As a result, even large models made of PLA or ABS retain their geometry and do not curl at the edges.</p> <p> (image) </p><h3>Very fast and precise printing</h3> <p>The use of FOC stepper motors in a closed loop increases drive efficiency by up to 65%. The maximum printing speed reaches 800 mm/s, and the acceleration reaches 30,000 mm/s². This configuration significantly reduces project completion time while maintaining high accuracy.</p> <p> (image) </p><h3>Stable CoreXY design</h3> <p>The CoreXY motion system with 10 mm wide 1.5GT belts ensures high rigidity and accuracy of the head guidance. The X-axis uses a high-hardness linear guide, the Y-axis uses 12 mm steel shafts, and the Z-axis uses four guides and two independent motors with trapezoidal screws. This allows the printer to remain stable even with large and heavy models.</p> <p> (image) </p><h3>Automatic leveling and print control</h3> <p>The printer is equipped with automatic table leveling with a load cell sensor integrated into the hot end. The monitoring system includes a filament end sensor, an AI camera, and a print resume function after a power failure. This makes the printing process safer and requires less manual control.</p> <p> (image) </p><h3>Air filtration and convenient operation</h3> <p>The QIDI Max 4 has a 3-stage air filtration system consisting of a G3 pre-filter, HEPA H12 filter, and activated coconut carbon. The printer is also equipped with a 5-inch touch screen, Wi-Fi and Ethernet connectivity, and a 1080p camera for viewing and recording timelapse footage of the printing process.</p> <p> (image) </p> <h3>Included</h3> <ul class="list-disc pl-5"><li>Filament holder with pneumatic head</li><li>Filament spool holder</li><li>Holder cover</li><li>Case door handle</li><li>Spare parts kit</li><li>Mechanism maintenance oil</li><li>7 mm wrench</li><li>Power cord</li><li>Ethernet cable</li><li>USB flash drive with software and files</li><li>Flat screwdriver</li><li>Adhesive for the work surface to improve print adhesion</li><li>Set of Allen keys (H1.27, H1.5, H2, H2.5, H3)</li><li>Scraper for removing prints from the table</li></ul> <div class="table-wrapper"> <p> </p> <h3></h3> <table> <tbody> <tr><th>Manufacturer</th><td>QiDi</td></tr><tr><th>Model</th><td>Max 4</td></tr><tr><th>Working area</th><td>390 × 390 × 340 mm</td></tr><tr><th>Printer dimensions</th><td>558 × 578 × 612 mm</td></tr><tr><th>Weight</th><td>40 kg</td></tr><tr><th>Maximum head temperature</th><td>up to 370°C</td></tr><tr><th>Maximum table temperature</th><td>up to 120°C</td></tr><tr><th>Chamber temperature</th><td>up to 65°C (active heating – 3rd generation)</td></tr><tr><th>Maximum print speed</th><td>800 mm/s</td></tr><tr><th>Maximum acceleration</th><td>30,000 mm/s²</td></tr><tr><th>Extruder</th><td>Direct Drive, hardened steel double gears</td></tr><tr><th>Supported filaments</th><td>PLA, ABS, ASA, PETG, TPU, PA, PC, carbon fiber and glass fiber composites</td></tr><tr><th>Filament diameter</th><td>1.75 mm</td></tr><tr><th>Material flow</th><td>40 mm³/s</td></tr><tr><th>Automatic leveling</th><td>yes (load cell sensor in the hotend)</td></tr><tr><th>Filament sensor</th><td>yes – filament end detection</td></tr><tr><th>Air filter</th><td>3-in-1: G3 + HEPA H12 + activated carbon</td></tr><tr><th>Camera</th><td>1080p with timelapse support</td></tr><tr><th>Connectivity</th><td>Wi-Fi 2.4/5 GHz, Ethernet, USB</td></tr><tr><th>Memory</th><td>32 GB eMMC + USB 2.0</td></tr><tr><th>Screen</th><td>5" touchscreen 800 × 480</td></tr><tr><th>Supported file formats</th><td>STL, OBJ, 3MF, STEP, STP</td></tr><tr><th>Software</th><td>QIDI Studio, OrcaSlicer, PrusaSlicer, and others</td></tr><tr><th>Power supply</th><td>110V / 220–240V AC, 50/60 Hz</td></tr><tr><th>Rated power</th><td>150 W + 500 W (chamber heating) + 700 W (heating bed)</td></tr> </tbody> </table> </div>

<h3>Qidi Q2 3D Printer</h3> <p>The Qidi Q2 3D printer is an advanced CoreXY-based device with a build volume of 270 × 270 × 256 mm, a print speed of up to 600 mm/s, and an acceleration of up to 20,000 mm/s². It offers a nozzle temperature of up to 370°C and a closed, actively heated chamber up to 65°C, allowing it to work with both basic filaments like PLA and more demanding engineering materials. Automatic offset-free leveling, smart features, and a stable design mean the device is ready to use almost immediately, without lengthy setup or testing.</p> <p> (image) </p><h3>Accurate first layer without manual calibration</h3> <p>The leveling system, which uses the nozzle as a sensor, eliminates the need for manual offset adjustment and first-layer height correction. Thanks to direct contact with the build plate surface, the printer obtains a real-time measurement, resulting in greater accuracy. In practice, this means fewer errors at the start, better model adhesion, and greater print repeatability, especially for larger or more demanding projects.</p> <p> (image) </p><h3>Speed that actually reduces processing time</h3> <p>The combination of speeds up to 600 mm/s with acceleration of 20,000 mm/s² allows the printer to quickly reach full operating speed and move efficiently even with frequent changes in direction. This has a direct impact on model production time, especially for those with complex geometries. Shorter print times mean greater productivity, which is important for both hobbyist work and the production of larger quantities of parts.</p> <p> (image) </p><h3>Improved surface and detail quality</h3> <p>The new 1.5GT belt with increased tooth density improves the precision of axis movement, and the resonance control system reduces vibrations generated during operation. This minimizes wall waviness and layer visibility. As a result, prints are more uniform and details are better reproduced, which is important for visual elements and parts requiring precision.</p> <p> (image) </p><h3>Stable construction and long-lasting precision</h3> <p>The metal frame in the CoreXY design and linear guides ensure high rigidity and wear resistance. This construction minimizes mechanical play and improves the accuracy of the print head’s positioning. As a result, the printer maintains stable operating parameters even during intensive use, which translates to repeatability and reduced need for servicing.</p> <p> (image) </p><h3>Ready for engineering materials</h3> <p>The heated chamber up to 65°C maintains stable temperature conditions during printing. This is particularly important for materials such as ABS, ASA, or PC, which are sensitive to temperature changes and may warp. Better control of the printing environment enhances layer adhesion, resulting in stronger and more durable prints.</p> <p> (image) </p><h3>High-temperature print head and durable components</h3> <p>A hotend reaching up to 370°C enables printing with a wide range of filaments, including engineering materials. An improved cooling system reduces the risk of clogging, resulting in more stable operation. A bimetallic nozzle made of hardened steel increases wear resistance, which is essential when working with filaments containing fibers. A dual-drive extruder ensures even material feeding, which impacts the quality of the entire print.</p> <p> (image) </p><h3>Print Control and Device Protection</h3> <p>The built-in AI camera monitors the printing process in real time and detects "spaghetti" errors—situations where the model stops building correctly. In such cases, the printer can automatically pause operation, which minimizes material waste and prevents further issues. Additionally, the device supports filament end detection and tangling detection (using the QIDI BOX, which can be purchased separately), which protects the process from sudden interruptions.</p> <p> (image) </p><h3>Safe and convenient everyday operation</h3> <p>The integrated 3-in-1 filtration system (G3 pre-filter, HEPA H12, and activated carbon) reduces dust and odors generated during printing, improving comfort when working in enclosed spaces. The NFC system automatically recognizes compatible filaments and selects the appropriate settings, simplifying operation. Additionally, temperature sensors and PTC protection continuously monitor the device’s operation and cut off power if any abnormalities are detected, enhancing safety during use.</p> <p> (image) </p> <div class="table-wrapper"> <p> </p> <h3></h3> <table> <tbody> <tr><th>Manufacturer</th><td>QIDI</td></tr><tr><th>Model</th><td>Q2</td></tr><tr><th>Printing technology</th><td>FDM</td></tr><tr><th>Kinematics</th><td>CoreXY</td></tr><tr><th>Build volume</th><td>270 × 270 × 256 mm</td></tr><tr><th>Print speed</th><td>up to 600 mm/s</td></tr><tr><th>Acceleration</th><td>up to 20,000 mm/s²</td></tr><tr><th>Nozzle temperature</th><td>up to 370°C</td></tr><tr><th>Chamber temperature</th><td>up to 65°C (active heating)</td></tr><tr><th>Supported materials</th><td>PLA, PETG, ABS, ASA, PC, and composite materials (e.g., carbon fiber, glass fiber)</td></tr><tr><th>Connectivity and interfaces</th><td>2.4 GHz Wi-Fi, Ethernet, USB (file transfer and updates)</td></tr><tr><th>Device dimensions</th><td>402 × 438 × 494 mm</td></tr><tr><th>Weight</th><td>25 kg</td></tr> </tbody> </table> </div>

<h3>QiDi Q2 Combo 3D printer</h3> <p>The QiDi Q2 Combo 3D printer has been designed for people who expect high-quality prints and stable operation even at high speeds. The device combines a precise leveling system, a modern CoreXY design, and an efficient hotend with a temperature of up to 370°C. This allows the printer to handle both popular filaments and more demanding technical materials. The solutions used improve print repeatability, reduce first layer errors, and improve the overall surface quality of models.</p> <p> (image) </p><h3>A new generation of automatic leveling</h3> <p>The QiDi Q2 Combo uses a leveling sensor in which the nozzle itself acts as the sensor. This means actual contact with the table surface, without the need for an offset probe. This eliminates errors resulting from inaccurate measurements or differences in the table surface. Automatic leveling is completely maintenance-free and allows you to quickly prepare the printer for operation, ensuring accurate placement of the first layer.</p> <p> (image) </p><h3>High speed and precise movement</h3> <p>The CoreXY design and the new 1.5GT belt with higher tooth density ensure smoother head movement. This reduces vibration and limits the formation of artifacts visible on the surface of prints. Intelligent resonance control further stabilizes the mechanism, so even at high speeds, the printer maintains good detail quality and smooth model surfaces.</p> <p> (image) </p><h3>Efficient hotend for technical materials</h3> <p>The new hotend design allows operation at temperatures up to 370°C. The ceramic throat and redesigned heat dissipation system help reduce the risk of nozzle clogging during long prints. The bimetallic hardened steel nozzle increases wear resistance, which is especially important when working with filaments containing carbon or glass fibers.</p> <p> (image) </p><h3>Stable working chamber and temperature control</h3> <p>The printer is equipped with a second-generation heated working chamber that can reach temperatures of up to 65°C. This makes it possible to print more demanding materials, such as ABS or PC, with less risk of deformation. The heated bed with an aluminum base and double-sided PEI plate ensures good adhesion of models and facilitates their removal after printing.</p> <p> (image) </p><h3>Smart features and operation monitoring</h3> <p>The QiDi Q2 Combo offers a set of features that support convenient operation. The camera allows you to preview your print in up to 1080p resolution and create timelapse recordings. Sensors detect when filament is running low, and the optional QIDI Box system allows for multi-color printing and material entanglement detection. The power failure recovery system allows you to continue printing without having to start over from the beginning.</p> <p> (image) </p><h3>AI camera and print error detection</h3> <p>The QiDi Q2 Combo printer is equipped with an AI camera that monitors the printing process and helps detect potential problems during operation. The system analyzes the image in real time and can detect irregularities such as the so-called "spaghetti" effect, which occurs when the print peels off the table or the filament begins to accumulate in an uncontrolled manner. This makes it possible to quickly notice the problem and react, which increases the safety of the printer and reduces material waste during long or more demanding prints.</p> <p> (image) </p> <div class="table-wrapper"> <p> </p> <h3></h3> <table> <tbody> <tr><th>Manufacturer</th><td>QiDi</td></tr><tr><th>Model</th><td>Q2 Combo</td></tr><tr><th>Working area</th><td>270 × 270 × 256 mm</td></tr><tr><th>Printer dimensions</th><td>402 × 438 × 494 mm</td></tr><tr><th>Weight</th><td>18.1 kg</td></tr><tr><th>Head temperature</th><td>up to 370°C</td></tr><tr><th>Work table temperature</th><td>up to 120°C</td></tr><tr><th>Nozzle diameter</th><td>0.4 mm (optional 0.2 / 0.6 / 0.8 mm)</td></tr><tr><th>Extruder</th><td>Direct Drive, hardened steel gears</td></tr><tr><th>Maximum head speed</th><td>600 mm/s</td></tr><tr><th>Maximum acceleration</th><td>up to 20000 mm/s²</td></tr><tr><th>Supported filaments</th><td>PLA, ABS, ASA, PETG, TPU, PA, PC, carbon and glass fiber composites, and others</td></tr><tr><th>Filament diameter</th><td>1.75 mm</td></tr><tr><th>Multi-color printing</th><td>Compatible with QIDI Box</td></tr><tr><th>Camera</th><td>Up to 1080p, timelapse support</td></tr><tr><th>Filament sensors</th><td>Filament end sensor and tangling detection (with QIDI Box)</td></tr><tr><th>Power failure resume function</th><td>Yes</td></tr><tr><th>Connectivity</th><td>2.4 GHz Wi-Fi, Ethernet, USB</td></tr><tr><th>Memory</th><td>32 GB eMMC + USB 2.0 memory</td></tr><tr><th>Display</th><td>4.3" touchscreen (480 × 272)</td></tr><tr><th>Slicing software</th><td>QIDI Studio, OrcaSlicer, PrusaSlicer, and others</td></tr><tr><th>Supported file formats</th><td>STL, OBJ, 3MF, STEP, STP</td></tr><tr><th>Power supply</th><td>110V / 220–240V AC, 50/60 Hz</td></tr><tr><th>Rated power</th><td>350 W + 280 W (chamber heating)</td></tr> </tbody> </table> </div>

<h3>QIDI Q2C 3D Printer</h3> <p>The QIDI Q2C is a 3D printer designed as a fast and precise tool for working with a wide range of engineering materials, offering a large build volume of 270 × 270 × 256 mm and a high print speed of up to 600 mm/s with acceleration of up to 20,000 mm/s². The design, based on a rigid, all-metal CoreXY frame, ensures operational stability even during intense head movement, while the High Hardness Linear Guide Rail system on the X-axis maintains smooth and accurate movement over the long term. The system is complemented by a new 1.5GT belt with increased tooth density, which reduces vibration and improves the surface quality of prints. Combined with a hotend capable of reaching temperatures up to 370°C, the printer is ready to handle demanding filaments, including carbon and glass fiber composites and high-temperature materials such as PPS-CF.</p> <p> (image) </p><h3>Stable CoreXY design and precise movement</h3> <p>The use of a full metal frame in the CoreXY layout helps reduce vibrations and maintain high structural rigidity even at high operating speeds. Combined with high-hardness linear guides, X-axis movement remains smooth and repeatable, which directly impacts the dimensional accuracy of models. The drive system has been optimized to reduce vibration artifacts, resulting in smoother and more consistent print surfaces.</p> <p> (image) </p><h3>Extruder and handling of demanding materials</h3> <p>The dual filament drive system, combined with hardened steel extruder components, ensures stable and reliable material feeding. The design is optimized for use with engineering and abrasive filaments, allowing for the printing of materials such as carbon fiber or glass fiber composites without excessive wear on the mechanism. As a result, the device maintains repeatability even during long and demanding projects.</p> <p> (image) </p><h3>Process Automation and Ecosystem Support</h3> <p>The printer utilizes a new-generation leveling system in which the nozzle acts as a sensor. This allows for accurate measurement of the build plate surface without offsets or additional probes, which increases the precision of the first layer and reduces the risk of errors. Within the QIDI ecosystem, in conjunction with the QIDI Box (not included), features are also available to automate filament handling, including intelligent detection of certain system operating conditions, such as material feeding issues or filament tangles, which helps reduce the risk of failed prints.</p> <p> (image) </p><h3>Speed, display, and connectivity</h3> <p>The QIDI Q2C is designed as a high-speed production printer, offering print speeds of up to 600 mm/s and high accelerations of up to 20,000 mm/s², which significantly reduces project turnaround times. The device is equipped with a 4.3-inch touchscreen that facilitates operation and control of operating parameters. Various connectivity options are also available, including Wi-Fi and Ethernet, allowing for integration into networked environments in workshops and production facilities.</p> <p> (image) </p><h3>Safety and Operation Control</h3> <p>The safety system relies on continuous temperature monitoring and the use of electronic safeguards that respond when abnormalities are detected. As a result, the printer can automatically cut off power in emergency situations, which enhances safety during long and demanding prints.</p> <p> (image) </p> <div class="table-wrapper"> <p> </p> <h3></h3> <table> <tbody> <tr><th>Manufacturer</th><td>QIDI</td></tr><tr><th>Model</th><td>Q2C</td></tr><tr><th>Technology</th><td>FDM</td></tr><tr><th>Build volume</th><td>270 × 270 × 256 mm</td></tr><tr><th>Maximum hotend temperature</th><td>≤ 370°C</td></tr><tr><th>Maximum bed temperature</th><td>≤ 120°C</td></tr><tr><th>Maximum print speed</th><td>up to 600 mm/s</td></tr><tr><th>Acceleration</th><td>≤ 20,000 mm/s²</td></tr><tr><th>Nozzle diameter</th><td>0.4 mm (optional 0.2 / 0.6 / 0.8 mm)</td></tr><tr><th>Supported filament</th><td>1.75 mm</td></tr><tr><th>Supported materials</th><td>PLA, ABS, ASA, PETG, TPU, PA, PC, composites: Carbon Fiber / Glass Fiber Reinforced, high-temperature materials (e.g., PPS-CF)</td></tr><tr><th>Wi-Fi</th><td>2.4 GHz</td></tr><tr><th>Ethernet</th><td>Yes</td></tr><tr><th>USB</th><td>Yes</td></tr><tr><th>Printer dimensions</th><td>402 × 438 × 494 mm</td></tr> </tbody> </table> </div>

<h3>QiDi Q2C Combo 3D printer</h3> <p>The QiDi Q2C Combo printer is a modern device designed for fast and precise 3D printing. It offers a large workspace, high hotend operating temperature, and stable CoreXY construction, making it suitable for both hobbyist projects and more demanding technical applications. With support for multiple filament types and the ability to work with the QIDI Box system for multi-color printing, the printer offers great freedom in model creation.</p> <p> (image) </p><h3>Large workspace</h3> <p>The QiDi Q2C Combo offers a working area of 270 × 270 × 256 mm, allowing you to print larger parts or multiple models at the same time. This workspace gives you more design freedom and reduces the need to split models into smaller parts. The stable construction of the device, measuring 402 × 438 × 494 mm, ensures adequate rigidity during operation.</p> <p> (image) </p><h3>New generation automatic leveling</h3> <p>The printer uses a modern leveling sensor in which the nozzle itself acts as a sensor. This means direct contact with the work table surface, which eliminates the problem of probe offset and measurement errors. The system works independently of the type of table surface or environmental vibrations, so the first layer is accurate and repeatable. This makes printer configuration easier and the leveling process automatic.</p> <p> (image) </p><h3>High speed and precision of movement</h3> <p>The QiDi Q2C Combo is equipped with a CoreXY design and a new 1.5GT drive belt with increased tooth density. This solution improves smoothness of movement and reduces vibrations that can affect print quality. The printer achieves a head speed of up to 600 mm/s and acceleration of up to 20,000 mm/s², which significantly reduces printing time without compromising precision.</p> <p> (image) </p><h3>Modern hotend up to 370°C</h3> <p>The new generation hotend allows operation at temperatures up to 370°C. The design with a ceramic throat and an improved heat dissipation system reduces the risk of nozzle clogging. The bimetallic hardened steel nozzle is wear-resistant, making it well suited for filaments containing carbon or glass fibers.</p> <p> (image) </p><h3>Support for multiple materials</h3> <p>The printer supports a wide range of 1.75 mm diameter filaments. It is possible to print with popular materials such as PLA, PETG, and ABS, but also with more demanding materials such as ASA, TPU, PA, and PC. Thanks to its durable nozzle and steel extruder gears, the printer can also handle filaments reinforced with carbon or glass fibers.</p> <p> (image) </p><h3>Stable work platform</h3> <p>The model is equipped with a heated work table with an aluminum base that reaches a temperature of up to 120°C. Its surface features a double-sided magnetic PEI plate, which ensures good adhesion of prints during operation and facilitates their quick removal after printing.</p> <p> (image) </p><h3>Convenient operation and connectivity</h3> <p>The printer has a 4.3-inch color touch screen that allows for convenient control of the device's functions. It supports Wi-Fi, Ethernet, and USB connectivity, making it easy to transfer files for printing. The device works with QIDI Studio software and popular slicers such as Orca and PrusaSlicer. Supported file formats include STL, OBJ, 3MF, STEP, and STP.</p> <p> (image) </p><h3>Additional features for increased convenience</h3> <p>The QiDi Q2C Combo is equipped with a power loss recovery feature and a filament end sensor. The printer also supports an optional camera with timelapse function and an air filter. Additionally, it can be used with the QIDI Box system, which allows for multi-color printing and material feed control.</p> <p> (image) </p> <div class="table-wrapper"> <p> </p> <h3></h3> <table> <tbody> <tr><th>Manufacturer</th><td>QiDi</td></tr><tr><th>Model</th><td>Q2C Combo</td></tr><tr><th>Printing technology</th><td>FDM</td></tr><tr><th>Working area</th><td>270 × 270 × 256 mm</td></tr><tr><th>Maximum printing speed</th><td>up to 600 mm/s</td></tr><tr><th>Maximum acceleration</th><td>up to 20000 mm/s²</td></tr><tr><th>Filament diameter</th><td>1.75 mm</td></tr><tr><th>Nozzle diameter</th><td>0.4 mm</td></tr><tr><th>Maximum head temperature</th><td>up to 370°C</td></tr><tr><th>Maximum table temperature</th><td>up to 120°C</td></tr><tr><th>Compatible filaments</th><td>PLA, ABS, ASA, PETG, TPU, PA, PC, and carbon fiber or glass fiber reinforced filaments</td></tr><tr><th>Multi-color system</th><td>Compatible with QIDI Box</td></tr><tr><th>Screen</th><td>4.3 inches, touchscreen (480 × 272)</td></tr><tr><th>Connectivity</th><td>2.4 GHz Wi-Fi, Ethernet, USB</td></tr><tr><th>Memory</th><td>32 GB eMMC + USB Flash Drive</td></tr><tr><th>Filament sensor</th><td>Yes (Run-out sensor)</td></tr><tr><th>Print resumption after power failure</th><td>Yes</td></tr><tr><th>Slicer</th><td>QIDI Studio, OrcaSlicer, PrusaSlicer, and other compatible programs</td></tr><tr><th>Supported file formats</th><td>STL, OBJ, 3MF, STEP, STP</td></tr><tr><th>Voltage</th><td>110V / 220–240V AC, 50/60Hz</td></tr><tr><th>Rated power</th><td>350 W</td></tr><tr><th>Printer dimensions</th><td>402 × 438 × 494 mm</td></tr><tr><th>Package dimensions</th><td>480 × 520 × 585 mm</td></tr><tr><th>Weight</th><td>16.9 kg</td></tr> </tbody> </table> </div>