The graphene thermal pads in the Thermal Grizzly KryoSheet series are an excellent alternative to high-performance thermal pastes. Like the Carbonaut pads, they feature an adaptable surface with extremely high thermal conductivity, but as a high-end product, KryoSheet provides significantly higher thermal conductivity than Carbonaut pads. This improvement is due not only to the choice of materials but also to an innovative manufacturing process. KryoSheet contains no liquid components, meaning it does not age like traditional thermal paste and cannot dry out. Outstanding thermal conductivity Easy to use Consistent high performance Extreme durability Attention: Electrically conductive! Follow the instructions! The KryoSheet graphene pads have a molecular structure stacked in the Z-direction. This optimized structure provides exceptional and consistent thermal conductivity, thanks to a specially designed manufacturing process in which the hexagonal crystal structure of graphite is broken along the basal plane to harness the anisotropy of graphite’s thermal conductivity. However, a side effect of this complex process is increased electrical conductivity and changed pad stability, so KryoSheet pads must only be used as instructed! Note: Reuse of KryoSheet is not recommended! When removing the cooler and handling KryoSheet after use, micro-cracks may form within the graphene pad structure, which could impact performance. KryoSheet is available in multiple sizes to fit various CPU and GPU models. The KryoSheet 29×25 mm is compatible with: Nvidia GPUs: RTX 5080 RTX 4090 RTX 3080, RTX 3080 Ti, RTX 3090, RTX 3090 Ti RTX 2070 Super, RTX 2080, RTX 2080 Super AMD GPUs: RX 7900 XT, RX 7900 XTX RX 6800, RX 6800 XT, RX 6900 XT, RX 6950 XT Intel GPUs: Arc A750, Arc A770
Tootekood: UGREEN/55567GTIN: 6941876255672Video cables and adapters
【Cutting Edge 16K DisplayPort Cable】UGREEN16K DisplayPort cable 2.1 supports high resolutions 16K@60Hz, 8K@240Hz, 4K@240Hz. And backward compatible with Display Port 1.4 1.3, 1.2. Single-screen video output of 16K@60Hz (DSC 1.2a), and dual-screen supported. The DP to DP cable also supports HDR, HDCP 2.2, FEC forward error correction and UHBR10 which guarantee your immersive viewing experience. (Note: 20-pin is disabled with no power. No need to worry about the 20-pin issues.) 【VESA Certified 80Gbps DP Cable 2.1】This Display Port 2.1/2.0 cable features an unprecedented bandwidth of 80Gbps, nearly 3 times what was available in the previous DP 1.4 spec. Stable and high-speed transmission without signal loss. The DisplayPort cable also backward compatible with previous DP 1.4 and DP 1.2 standards. The monitor cable meets the VESA Standard and supports 3D&HDR and Dolby&eARC to provide you with amazing sound and image quality. 【Optimized for Game Enthusiasts】The DP cable 2.1 is highly recommended for game setups as it works well with game monitors and graphics cards, delivering high-quality video and audio signals with no lag or interference. It supports FreeSync and G-Sync, which are essential for gaming. You can easily connect multiple monitors with Multi-Stream Transport (MST). Variable refresh rate (VRR) and auto low latency mode (ALLM) bring you smoother game experience especially in FPS, 3A and MOBA games. 【Ultra Durability】UGREEN DisplayPort cable port with no buckle design can prevent accidental damage. DP cable 2.1 is made of 28AWG tinned copper and tinplate which features triple shielding and resistance with EMI. Aluminum alloy housing is resistant to rust and can accelerate heat dissipation. The Display Port cord has a strong nylon braided jacket, which is 10X more durable than PVC. It can provide higher connectivity and longer service life for better signal transmission. 【Wide Compatibility】UGREEN 16K@60Hz DisplayPort to DisplayPort cable is compatible with all devices with DP ports, compatible with Nvidia RTX 3070/RTX 3080/RTX 3090/RTX 4090/RTX 4080ti/RTX 4070ti graphics cards, and AMD Radeon RX 6800 XT/RX 6900 XT/RX 7900 XT graphics cards, and Odyssey G8/G9, Ben Q, Alienware, LG Ultragear monitors, HDTV, Fire TV, computer and others. Support DP, DP++ modes, backward compatible 2.0/1.4/1.3/1.2 DisplayPort 2.1 Reinforced Joint Bare Copper Nylon Braided
The HEATKILLER® V eBC backplate is a useful addition to the graphics card coolers of the HEATKILLER® V series. Mounted on the back of the graphics card, it improves cooling performance and mechanical stability. This is made possible by the use of solid black anodized aluminum. The milled logos and indirect lighting are also eye-catchers. The backplate cools relevant components on the back of the board, including the GPU and voltage converter (VRM). Pre-cut thermal pads are included in the delivery. Spacers (electrically insulating) attached to the back of the backplate ensure easy installation on the graphics card. The included mounting material is optimized for use with a water cooler from the HEATKILLER® V series. Technical data: Material: anodized aluminum Dimensions: (L x W x H): Weight: 150g Compatibility: EVGA GeForce RTX 3080 FTW3 EVGA GeForce RTX 3080Ti FTW3 EVGA GeForce RTX 3090 FTW3 See also http://gpu.watercool.de for further information Scope of delivery: 1x HEATKILLER® V eBC - Backplate for RTX 3080/3090 EVGA FTW3 - Black 1x mounting material
The HEATKILLER® V eBC backplate is a useful addition to the HEATKILLER® V series graphics card coolers. Mounted on the back of the graphics card, it improves cooling performance and mechanical stability. This is made possible by the use of solid black anodized aluminum. The milled logos and indirect lighting are also discreet eye-catchers. The backplate cools relevant components on the back of the board, including the GPU and voltage converter (VRM). Pre-cut thermal pads are included in the delivery. Spacers (electrically insulating) attached to the back of the backplate ensure easy installation on the graphics card. The included mounting material is optimized for use with a HEATKILLER® V series water cooler. Technical data: Material: nickel-plated aluminum, insulated Dimensions: (L x W x H): Weight: 150g Compatibility: EVGA GeForce RTX 3080 FTW3 EVGA GeForce RTX 3090 FTW3 EVGA GeForce RTX 3080Ti FTW3 See also http://gpu.watercool.de for further information Scope of delivery: 1x HEATKILLER® V eBC - Backplate for RTX 3080/3090 EVGA FTW3 - Black 1x mounting material
With the HEATKILLER® V, Watercool is starting a new generation of coolers for the current Nvidia RTX 30 graphics cards. Equipped with unique highlights, the current version of the HEATKILLER® V presents what is technically feasible. With an increased number of cooling fins, the cooling performance is increased directly above the graphics processor and thus the most important area is improved. The radiator base, milled from a solid block, establishes contact with all relevant components. The trend-setting dual-layer inflow distributes the water simultaneously on two levels. This ensures an air flow that is at least 30 percent higher than that of our previous generation. The broad and symmetrical flow paths reduce dead spots (standing water) to a minimum and accelerate the flow. The overall result increases not only the maximum cooling capacity but also the flow rate of the HEATKILLER® V. Thanks to the newly designed spacers made of high-performance plastic (PEEK), the 10mm solid copper block is ideally isolated from the circuit board. In addition to the technical innovations, the design of the cooler is also impressive. The screwless cover makes the entire block look like it was cast from a single source. The symmetrically designed channels underline the look of the cooler and make it a unique eye-catcher. Technical specifications: Base plate material: electrolyte copper Material cover: acrylic glass Cover material: black anodized aluminum Connection terminal material: Acetal Dimensions: (LxWxH): 230 x 119 x 21 mm Connection: 4x G ¼ inch (DIN ISO 228-1) Weight: Pressure tested: 2 bar Compatibility: Nvidia Geforce RTX 3080/3090 Scope of delivery: 1x HEATKILLER® V 1x mounting material Thermal Grizzly Kryonaut thermal paste
With the HEATKILLER® V, Watercool is starting a new generation of coolers for the current Nvidia RTX 30 graphics cards. Equipped with unique highlights, the current version of the HEATKILLER® V presents what is technically feasible. With an increased number of cooling fins, the cooling performance is increased directly above the graphics processor and thus the most important area is improved. The radiator base, milled from a solid block, establishes contact with all relevant components. The trend-setting dual-layer inflow distributes the water simultaneously on two levels. This ensures an air flow that is at least 30 percent higher than that of our previous generation. The broad and symmetrical flow paths reduce dead spots (standing water) to a minimum and accelerate the flow. The overall result increases not only the maximum cooling capacity but also the flow rate of the HEATKILLER® V. Thanks to the newly designed spacers made of high-performance plastic (PEEK), the 10mm solid copper block is ideally isolated from the circuit board. In addition to the technical innovations, the design of the cooler is also impressive. The screwless cover makes the entire block look like it was cast from a single source. The symmetrically designed channels underline the look of the cooler and make it a unique eye-catcher. The integrated aRGB strips are now standard in combination with the nickel-acrylic variants. This means that the HEATKILLER® V can be perfectly integrated into the lighting concept of the computer. Technical specifications: Base plate material: nickel-plated electrolyte copper Material cover: acrylic glass Cover material: annealed stainless steel Connection terminal material: Acetal Dimensions: (LxWxH): Connection: 4x G ¼ inch (DIN ISO 228-1) Weight: Pressure tested: 2 bar Compatibility: EVGA Geforce RTX 3080 XC3 EVGA Geforce RTX 3090 XC3 Scope of delivery: 1x HEATKILLER® V 1x HEATKILLER® LED Strip aRGB 1x mounting material Thermal Grizzly Kryonaut thermal paste
The HEATKILLER® V eBC backplate is a useful addition to the graphics card cooler of the HEATKILLER® V series. Mounted on the back of the graphics card, it improves cooling performance and increases mechanical stability. This is made possible by the use of solid black anodized aluminum. The optics are not neglected either. The backplate cools relevant components on the back of the board, including the GPU and voltage converter (VRM). Pre-cut thermal pads are included in the scope of delivery. Spacers (electrically insulating) attached to the back of the backplate ensure problem-free installation on the graphics card. The enclosed mounting material is optimized for use with a water cooler from the HEATKILLER® V series. Technical specifications: Material: anodized aluminum Dimensions: (L x W x H): Weight: 150g Compatible to: NVIDIA Geforce RTX 3080 NVIDIA Geforce RTX 3090 Scope of delivery: 1x HEATKILLER® V eBC - Backplate for RTX 3080/3090 - Black 1x mounting material
The HEATKILLER® V eBC backplate is a useful addition to the graphics card cooler of the HEATKILLER® V series. Mounted on the back of the graphics card, it improves cooling performance and increases mechanical stability. This is made possible by the use of solid black anodized aluminum. The optics are not neglected either. The backplate cools relevant components on the back of the board, including the GPU and voltage converter (VRM). Pre-cut thermal pads are included in the scope of delivery. Spacers (electrically insulating) attached to the back of the backplate ensure problem-free installation on the graphics card. The enclosed mounting material is optimized for use with a water cooler from the HEATKILLER® V series. Technical specifications: Material: anodized aluminum Dimensions: (L x W x H): Weight: 150g Compatibility: ZOTAC Geforce RTX 3080 Trinity ZOTAC Geforce RTX 3090 Trinity Scope of delivery: 1x HEATKILLER® V eBC - Backplate for RTX 3080/3090 Zotac Trinity - Black 1x mounting material
With the HEATKILLER® V, Watercool is starting a new generation of coolers for the current Nvidia RTX 30 graphics cards. Equipped with unique highlights, the current version of the HEATKILLER® V presents what is technically feasible. With an increased number of cooling fins, the cooling performance is increased directly above the graphics processor and thus the most important area is improved. The radiator base, milled from a solid block, establishes contact with all relevant components. The trend-setting dual-layer inflow distributes the water simultaneously on two levels. This ensures an air flow that is at least 30 percent higher than that of our previous generation. The broad and symmetrical flow paths reduce dead spots (standing water) to a minimum and accelerate the flow. The overall result increases not only the maximum cooling capacity but also the flow rate of the HEATKILLER® V. Thanks to the newly designed spacers made of high-performance plastic (PEEK), the 10mm solid copper block is ideally isolated from the circuit board. In addition to the technical innovations, the design of the cooler is also impressive. The screwless cover makes the entire block look like it was cast from a single source. The symmetrically designed channels underline the look of the cooler and make it a unique eye-catcher. Technical specifications: Base plate material: electrolyte copper Material cover: acrylic glass Cover material: annealed stainless steel Connection terminal material: Acetal Dimensions: (LxWxH): 230 x 119 x 21 mm Connection: 4x G ¼ inch (DIN ISO 228-1) Weight: Pressure tested: 2 bar Compatibility: Nvidia Geforce RTX 3080/3090 Scope of delivery: 1x HEATKILLER® V 1x mounting material Thermal Grizzly Kryonaut thermal paste
With the HEATKILLER® V, Watercool is starting a new generation of coolers for the current Nvidia RTX 30 graphics cards. Equipped with unique highlights, the current version of the HEATKILLER® V presents what is technically feasible. With an increased number of cooling fins, the cooling performance is increased directly above the graphics processor and thus the most important area is improved. The radiator base, milled from a solid block, establishes contact with all relevant components. The trend-setting dual-layer inflow distributes the water simultaneously on two levels. This ensures an air flow that is at least 30 percent higher than that of our previous generation. The broad and symmetrical flow paths reduce dead spots (standing water) to a minimum and accelerate the flow. The overall result increases not only the maximum cooling capacity but also the flow rate of the HEATKILLER® V. Thanks to the newly designed spacers made of high-performance plastic (PEEK), the 10mm solid copper block is ideally isolated from the circuit board. In addition to the technical innovations, the design of the cooler is also impressive. The screwless cover makes the entire block look like it was cast from a single source. The symmetrically designed channels underline the look of the cooler and make it a unique eye-catcher. The integrated aRGB strips are now standard in combination with the nickel-acrylic variants. This means that the HEATKILLER® V can be perfectly integrated into the lighting concept of the computer. Technical specifications: Base plate material: nickel-plated electrolyte copper Material cover: acrylic glass Cover material: annealed stainless steel Connection terminal material: Acetal Dimensions: (LxWxH): 230 x 119 x 21 mm Connection: 4x G ¼ inch (DIN ISO 228-1) Weight: Pressure tested: 2 bar Compatibility: Nvidia Geforce RTX 3080/3090 Scope of delivery: 1x HEATKILLER® V 1x HEATKILLER® LED Strip aRGB 1x mounting material Thermal Grizzly Kryonaut thermal paste
