Gleitmittel für das Biegen von Hard-Tubes von XSPC, verhindert das Steckenbleiben des Biegeschlauchs im Hard-Tube, erleichtert das Entfernen des Silikonschlauches aus dem Tube, für PETG- und Acryl-Tubes, 100 ml
The construction of a quiet computer is always a challenge, especially if performance and proper cooling are also a factor. The SF01 consists of two foam plastic sheets which help with noise absorption with minimal pressure inside of the system. Each sheet has a large surface and is made from very dense foam plastic with a thickness of 4mm. This ensures good noise reduction and flexible integration. Special features: Special high-grade EPOM foam plastic material for noise absorption Excellent adhesive properties even at high temperatures Simply cut to size: Fits in any computer case Contains two foam sheets Technical specifications: Colour: Black Material: EPOM Dimensions (WxLxD): 530x380x4mm Extent of delivery: 1x Silverstone noise absorption sheet (SST-SF01)
Technical Data: Material: Nickel-Plated Brass Color: Black Thread: G1/4" (male and female) Thread Length: 4,5 mm (male), 6 mm (female) Outer Diameter: 23 mm Installed Height: 31,5 mm
DEMCiflex Dust Filter 140mm White DF0689Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 140 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Note:The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Technical details:Size (frame): 153 x 153 mmSize (filter): 129 x 129 mmCompatibility: 140 mm fan slotMaterial (filter): polyester meshColor: white (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
DEMCiflex Dust Filter 140mm Round Black/White DF0495Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 140 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside or inside of the fan frame. If one of the two arrows points towards the interior or if the rotor suspension is aligned with the interior, this is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Technical details:Size (frame): Ø approx. 152 mmSize (filter): Ø approx. 127 mmCompatibility: 140 mm fan slotMaterial (filter): polyester meshColor: black (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
DEMCiflex Dust Filter 120mm Round Black/White DF0525Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 120 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Firstly, it is easy to see if cleaning is necessary again - as soon as the white filter fabric has a gray haze, you should do this task. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside of the fan frame. If one of the two arrows points towards the interior, it is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Figure 4 shows an example configuration on a housing (not included). As can be seen, the use of LED fans is possible because the transparent material hardly hampers the lighting. Technical details:Size (frame): Ø approx. 138 mmSize (filter): Ø approx. 113 mmCompatibility: 120 mm fan slotMaterial (filter): polyester meshColor: black (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
DEMCiflex Dust Filter 120mm Black/White DF0381Toote kirjeldus inglise keeles:Product description:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 120 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Firstly, it is easy to see if cleaning is necessary again - as soon as the white filter fabric has a gray haze, you should do this task. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside of the fan frame. If one of the two arrows points towards the interior, it is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Figure 4 shows an example configuration on a housing (not included). As can be seen, the use of LED fans is possible because the transparent material hardly hampers the lighting. Technical details:Size (frame): 128 x 128 mmSize (filter): 105 x 105 mmCompatibility: 120 mm fan slotMaterial (filter): polyester meshColor: black (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
120-mm-Gehäuselüfter, Drehgeschwindigkeit bis max. 2.000 U/min, maximale Lautstärke von 38,9 dB(A), 4-Pin-PWM-Anschluss, hohe Lebenserwartung von 70.000 Stunden
DEMCiflex Dust Filter 80mm Black/White DF0430Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 80 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Firstly, it is easy to see if cleaning is necessary again - as soon as the white filter fabric has a gray haze, you should do this task. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside of the fan frame. If one of the two arrows points towards the interior, it is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Figure 4 shows an example configuration on a housing (not included). As can be seen, the use of LED fans is possible because the transparent material hardly hampers the lighting. Technical details:Size (frame): 105 x 105 mmSize (filter): 80 x 80 mmCompatibility: 80 mm fan slotMaterial (filter): polyester meshColor: black (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
The new Alphacool NexXxos radiators, a name that stands for experience and quality has come to bring a fresh breeze to the radiator market.Every user of a water cooling system needs a radiator and everyone has different requirements towards the heat exchanger. Of course the customer always demands the best in its class. The Alphacool NexXxos radiators have come to compete with and to beat the best in their class and to be the best radiator in all sizes. No more endless choices without a clear class leader, the Alphacool NexXxos is the one tool for all your needs!Alphacool has been the company to introduce new developments and improvements in the radiator and water cooling sector generally many times over the last years.Following this tradition, the new NexXxos radiators are the first to truly deserve the “Full copper” attribute. All main parts, not only the fins and channels, but the chambers are also made from copper. This brings an improvement in performance where other radiators are left without a chance. In structure, the Alphacool NexXxoS X-Flow Radiators differentiate materially from the standard radiators. The X.Flow Radiators are designet for high flow rates. The bevelled copper chambers on both sides have an identical structure. This Water is jetting at the same time through all avialable channels to the other chamber to whitch it then leaves the radiator.Versatile and easy mounting is one of the main points, on which the research and development department at Alphacool focused. The chamber offers three possibilities for fitting installation on both inlet and outlet (not on the NexXos ST30). Less angled fittings are needed, improving flow rates and offering more mounting possibilities.Here, too, Alphacool provides the popular sizes of the 120mm series. Different thicknesses, 30mm, 45mm and 60 mm underscore the broad spectrum that cover these radiators. Even mounting and installation of fans and radiator grills is easy and versatile with these radiators: The M3 threads are standard in the radiator sector and available in all lengths at an affordable price.Even the dreaded insertion of a screw too far into the radiator does not result in expensive damage. Unlike other radiators, the NexXxos series is equipped with an internal protective ledge which stops the screw before it damages the fins.Fin spacing is always an important factor in radiator design. The new series from Alphacool has a fin design which allows it to perform extremely well even with slow-spinning and medium-speed fans. This is not only pleasant thanks to the fact that it avoids unnecessary noise; it also means that the choice of fans that can be used with these radiators is not restricted.These radiators are the result of experience and powerful performance meeting future-oriented design and well-thought through solutions.Alphacool NexXxos radiators: The one tool for all your cooling needs! Technical dataDimensions (L x W x H)413 x 124 x 45mmQuantity of cooling channels24Cooling channelsCopperColorblackFan threadM3Connection6x G1/4"SlatsCopperThickness39 - 49mmNumber of fans3Fan size120mmHousingSteelPressure tested0,8 barManufacturerAlphacoolFins per inch16
The perfect solution for perfect curves in the Alphacool HardTubes is now available. Simply slide the silicon insert into the plexiglass tube and heat up the desired section. Thanks to the extreme heat resistance of silicon, the tube can be bent without the curved section buckling. After it cools, the silicon insert can simply be pulled out. Available for tubes with 10mm, 12mm, and now 13mm inner diameters, and each size comes in 30cm length for curves in shorter tubes or 100cm length for curves in longer tubes. Technical Details Length: 30cm Thickness: 13mm Colour: blue Scope of Delivery 1x Alphacool silicon bending insert 30cm for ID 1/2” / 13mm HardTubes - blue NoticeDue to the manufacturing process, the diameter can vary by 0.5 - 1mm.
All new Flat (FLT) series EK-Quantum Kinetic FLT DDC pump-reservoir units! The new Kinetic combo units are part of the EK Quantum Line of products and come with sophisticated addressable D-RGB lighting implementation and a genuine DDC pump! Each unit is featuring standard 120mm fan mounting holes for maximum flexibility during the installation. The reservoir is equipped with a total of six G1/4“ ports so that users can choose the most optimal setup for their liquid cooling loops.EK-Quantum Kinetic FLT DDC series pump-reservoir units are equipped with genuine DDC 3.25 pumps, made in Europe, which are capable of delivering flow rates of 1000 liters per hour with a maximum head pressure up to 5.2 meters! These new FLT series combo units are available in three different sizes of 120mm, 240mm, and 360mm.The new flat-shaped pump-reservoir units are to revolutionize the way you were thinking about combo units and loop building. Since 120mm fan mounting patterns are the most dominant mounting options inside PC cases these days, these new Kinetic FLT DDC combo units will allow greater flexibility for installation since they don't require drilling of new mounting holes on your case.The combo unit is equipped with a total of six industry-standard G1/4" ports, which can be, based on the orientation of the unit, used as inlet and outlet ports, as well as fill and drain ports.The reservoir is manufactured of premium quality acrylic material, machined to perfection, while the sealing is performed by a quality EPDM o-ring. Alongside the reservoir is a black anodized aluminum cover under which the Addressable D-RGB LED strip is placed. Proper LED implementation is one of the main focus points of EK so that there are as few visible "LED hotspots" as possible.Pump electrical and mechanical properties:- Motor: Electronically commuted ball bearing motor- Rated voltage: 12 V DC- Power consumption: 18 W- Maximum head pressure: up to 5.2m- Maximum flow rate: up to 1000 L/h- Maximum liquid temperature: 60 °C- Materials: Stainless steel, PPS-GF40, EPDM O-rings, Aluminium oxide, hard coal- Power connector: 4-Pin Molex- and 4-Pin PWM FAN connectorOperational regime:- PWM duty cycle: ~ 20-100%- Default behavior: Runs at 100% duty cycle when no PWM feedback signal is presentEnclosed:- EK-Quantum Kinetic FLT 120 PWM D-RGB- Mounting mechanism with all necessary screws for 120mm fan mounting- Pair of EK reservoir holders with mounting screws- 4 × G1/4 Plugs - 1 × Allen key for reservoir holdersMade in Slovenia - EU!Pump motor made in Hungary - EU!PLEASE NOTE:Do not clean the reservoir with alcohol derivates or other solvents as the acrylic may crack!Coolant and additional plugs are just for showcase and are not delivered with the product!The DDC pump is water lubricated, in other words, it uses a wet rotor design. Therefore, it is strongly recommended not to run the pump dry.
The Barrow mini Water Stop Valve is made of full metal. Its construction makes it extremely robust. The housing is made of copper and the handle is made of aluminum. The stopcock has a G1 / 4 “internal thread with a length of approx. 5mm on both sides. Technical specifications: Color: black housing / black handle Material: copper / aluminum handle Thread: 2x G1 / 4 " Thread length: 5mm Dimensions: 37.2 x 35.5 x 23mm Flow opening: 10mm Scope of delivery: Barrow mini water stop valve
The Barrow mini Water Stop Valve is made of full metal. Its construction makes it extremely robust. The housing is made of copper and the handle is made of aluminum. The stopcock has a G1 / 4 “internal thread with a length of approx. 5mm on both sides. Technical specifications: Color: white housing / black handle Material: copper / aluminum handle Thread: 2x G1 / 4 " Thread length: 5mm Dimensions: 37.2 x 35.5 x 23mm Flow opening: 10mm Scope of delivery: Barrow mini water stop valve
EK-Loop Connect Level Sensor TBE 60 is a coolant level sensor provides a warning when the reservoir reaches a point where it would be prudent to top it off. Due to the coolant evaporation through the tubing, it makes sure the pump never runs dry. Also, in case of a leak, it warns you of the coolant level being below its optimal value. It attaches to the tube of the EK tubular-style reservoirs with 60mm diameter and connects via a dedicated cable to the EK-Loop Connect control unit. Technical Specifications: Connectors: 4-pin Length: 50cm
The EK-Loop Connect - USB External Cable 1m will allow the user to connect their EK-Loop Connect controller unit to the PC via a standard USB connector that can be found on the back of the motherboard. This type of connection is beneficial to modders because it allows them to pre-program the controller using another PC. This also makes it possible to run the pump, fan, and addressable RGB settings on another PC without the need to install an OS. This saves a great deal of time and still lets the user control D-RGB LED patterns for the needs of the video shoots, etc. Technical Specifications: Connectors: USB-A to 4-pin Length: 100cm
The EK-Torque Adapter 90 is a simple but elegant angle adapter, without logo branding. The adapter has a 90 degree angle, is rotatable and made of brass. Technical Data: Material: Nickel-Plated Brass Color: Black Thread: G1/4" (male and female) Thread Length: 4,5 mm (male), 6 mm (female) Outer Diameter: 23 mm Installed Height: 31,5 mm
EK-Loop UNI Pump Reservoir Bracket - 140mm is a mounting adapter for installation of EK D5, DDC, SPC, and VTX pumps and pump-reservoir combo units to any 140mm fan mounting hole pattern (125mm hole spacing). Additionally, it can be used with EK-RES X3 Holder 60mm (2pcs) to mount any reservoir or pump-reservoir combo with a tube of 60mm in diameter. It can be used horizontally or vertically. The offset on the bracket allows for precise placement of the pump or reservoir according to your needs for clearance or easier tube routing. By turning the bracket around the offset can be moved left, right, back, or forward in a horizontal setup, and also left, right, up, or down in a vertical setup. Made from press-bent 1,5mm thick painted steel. The height of the bracket is 11.5mm. This product is compatible with the following EK products: Vertical: EK-Quantum Kinetic TBE D5 series Vertical: EK-XRES Revo D5 series Vertical: EK-XRES X3 series Horizontal: EK-XTOP DDC series Horizontal: EK-XRES SPC Classic series Horizontal: EK-Quantum Kinetic TBE DDC series Horizontal: EK-Quantum Kinetic TBE VTX series Horizontal and Vertical: EK-XTOP Revo D5 series Enclosed: EK-Loop UNI Pump Reservoir Bracket - 140mm 5x polyamide washer M4 0.8mm 5x screws M4x6 DIN7984 5x nut M4 Allen key 2.5mm
EK Quantum Flow Indicator D-RGB is a high-quality flow indicator with addressable RGB lighting, which belongs to the Quantum Line. It visually represents the coolant flow rate, which is often difficult to see with the naked eye. This can be very useful to immediately see if your loop is in perfect condition or if there are problems with the pump or flow. In addition, this is a very elegant cast acrylic part covered by a nickel-plated aluminium cover. It has three G1/4" connectors, all of which are female. It can be mounted in the middle of a tube with two fittings or attached to a radiator or pump at each G1/4" connection. Each of the threads, can be used either as an inlet or outlet. This product is compatible with the common RGB synchronisation technologies of all major motherboard manufacturers. The nickel-plated aluminium cover hides the LED hotspots and provides uniform illumination. Enclosed: EK-Quantum Flow Indicator D-RGB – Nickel 1x G1/4" nickel-plated brass plug
The cooling units from Hailea have been used in trusted waterchillers from other manufacturers for over 15 years. The new heat exchangers of the Ultra series are made from titanium. Therefore the chillers are perfect for watercooling systems. Another positive aspect about the Hailea units is the low noise emission. The pricing of the new series is also pleasantly affordable. New revision: New cool design More robust materials for even longer lifespan Lowered noise emissions Suitable for continuous operation Noise emissions: The small chillers (like HC150) have a noise emission of 20dB(A) only and can be used near the computer / aquarium without disturbing. Bigger models (like HC500) should be additionally decoupled to reduce the noise level if necessary The models HC1000 und HC 2000 should be extra decoupled or maintained in a seperate room. This waterchiller basically replaces the radiator as the coolant is chilled to the desired temperature by this unit. Temperatures down to 4°C are possible, please note that at low temperatures (high temperature difference) condensate may accumulate. Suitable insulation accessories are also available in our shop. Alternatively the coolant temperature can be set to just below room temperature to avoid this problem. Thanks to the low temperatures incredible overclocking potential is available! The lifespan of the components is extended by multiples. This system is also great for no-noise applications as the chiller can be located in another room. We recommend integration of the chiller into the cooling loop in combination with a radiator. This allows use of the chiller when required (overclocking, Benchmarks, summer etc..) and use of the radiator during normal operation. To estimate the required cooling performance here some non-binding estimates. The exact thermal emissions can be requested from the manufacturer of the hardware. CPU: 80W (standard) to 150W (overclocked) GPU: 50W (small cards) to 250W (GTX 980) MB: 20 to 40W per component The added values of your system must not exceed the given cooling capability of the chiller. What aquarium size can be cooled with my water chiller? The manufacturer provides the following data: Model / aquarium size in liters: HC-130 / 50-100L HC-150 / 50-200L HC-250 / 100-300L HC-300 / 100-400L HC-500 / 200-800L HC-1000 / 300-1000L HC-2000 / 400-1500L We at Aquatuning wish to advise you that the manufacturer’s data was obtained under optimal circumstances. The temperature response of the aquarium may greatly vary because of insulation, heat from lights respectively sunlight. Hence we recommend using the larger model when reaching the upper limit of the aquarium size values. Note regarding shipping: This unit can only be shipped via a forwarding company. As the chipping charges differ by distance an online calculation is not possible. Please provide your full telephone number and E-Mail address when ordering, we will contact you after the order is complete. The shipping charge is approximately 50€ within Germany. Technical specifications: Power: 1 HP Power consumption: 550W Cooling capacity: 1650W (suitable for extreme OC and cooling) Recommended coolant flow: 2000-4000 l/h Weight: 31,5kg Cooling agent: R134A Dimensions: 400x500x440mm (LxWxH) Connector outside diameter: 23-27mm Heat exchanger material: Titanium max. compressive load: 0,8bar Temperature adjustments: Digital read-out (precision 0,1°C), temperature setting in 1°C steps current demand: 3.2 A (50 Hz) current drain: 736 W Scope of Delivery: 1x Waterchiller Hailea Ultra 2000 2x 90° angle with rubber seal 2x straight with rubber seal 2x suitable hose clamps Note for first-time users: If you should have problems with your chiller please contact us before returning the chiller to us. In most cases there is no actual problem with the chiller, but the functionality of the unit is not fully understood by the user yet. Please note the following: The compressor unit automatically switches itself on and off, if the temperature sensor is manipulated your warranty is void, the noise level or an allegedly not sufficient cooling performance are no reason for a reclamation. The chiller can only function properly if the cooling loop is equipped with a sufficiently powerful pump. If these facts are considered most reclamations can be avoided and you will greatly enjoy this product! Note for aquarium-use: The cooling performance is affected by the aquarium-lamp the reduced pump power due to filters and the thermal waste of the pump. We therefore recommend to order the ciller at least on power-lever higher that theoretically calculated This product has been reviewed for you (by): Overclockingstation Zockon bit-tech (engl.) How2 (Userreview): Hardwareluxx
The nickel-plated adapter from Bitspower in the colour shiny silver, has an angle of 90 degrees and two G1/4 inch internal threads, with rubber seals on both sides. Technical Data: Material: Nickel-Plated Brass Main Color: Shiny Silver Angle: 90° Thread: Inner G1/4" Thread Length: 6 mm
