DEMCiflex Dust Filter 140mm White DF0689Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 140 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Note:The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Technical details:Size (frame): 153 x 153 mmSize (filter): 129 x 129 mmCompatibility: 140 mm fan slotMaterial (filter): polyester meshColor: white (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
DEMCiflex Dust Filter 140mm Round Black/White DF0495Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 140 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside or inside of the fan frame. If one of the two arrows points towards the interior or if the rotor suspension is aligned with the interior, this is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Technical details:Size (frame): Ø approx. 152 mmSize (filter): Ø approx. 127 mmCompatibility: 140 mm fan slotMaterial (filter): polyester meshColor: black (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
This matt black T-splitter from Bitspower is made of brass and has three G1/4" internal threads. For example, a branch can be easily integrated into the main line of the water cooling system. Technical Data: Material: Brass Colour: Matt Black Connections: 3x G1/4" female thread Thread length: 5 mm
Hard Tube Fitting von EK Water Blocks, für Röhren mit 12 mm AD, Kompatibel zu Röhren aus Acryl / PETG / Kupfer / Messing / Edelstahl, mit optionalen Ringen farblich individualisierbar, 6er-Pack
Toote kirjeldus inglise keeles:To connect the individual components of the water cooling, the choice of the correct connections and their sufficient number is essential. Otherwise, installation will quickly become a frustrating experience if assembly fails on the wrong or too few connectors and is delayed due to this. Bitspower offers a comprehensive product range that offers the right solution for every requirement - whether adapters, direct hose connections, brackets or distributors. The design is solid and has a sealing ring. Thus, the connections remain tight and ensure high long-term durability. This is a matte black, straight adapter with two 1/4 inch external threads. In addition, the connection is rotatable, which significantly simplifies the screwing. Note: The turning function of the connections should always be used in the disassembled state, as this is relatively stiff due to the design. When installed, do not apply force to connections to avoid damaging the connectors themselves and the radiators on them. Technical details:Manufacturer's article no .: BP-MBRGMaterial: brassColor: matt blackConnections: male thread: 2x 1/4 inch
The nickel-plated adapter in matt black couples two tubes, which do not run on a common straight line, and ensures a bend of 30 degrees at the adapter. Two rubber rings seal both sides. The adapter is especially well compatible with the Crystal Link Tubes from Bitspower. Technical Data: Material: Nickel-Plated Brass Colour: Matt Black Angle: 30 ° Connections: 2x Ø 12 mm
The nickel-plated adapter in the color shiny black couples two tubes, which do not run on a common straight line and provides at the adapter for a bend of 90 degrees. Two rubber rings seal both sides. The adapter is especially well compatible with Bitspower's Crystal Link Tubes. Technical Data: Material: Nickel-Plated Brass Colour: Shiny Black Angle: 90 ° Connections: 2x Ø 12 mm
The adapter in matt black from Bitspower has a G1/4" external thread and a G1/4" internal thread. It has an angle of 90 degrees. Technical Data: Material: Brass Colour: Matt Black Angle: 90 ° Thread: G1/4" and inner G1/4" Thread Length : 5 mm
This filler neck in carbon black from Bitspower is used when coolant is filled into the cooling circuit from the top of the housing. To do this, cut a small opening in the housing, place the connection through the hole or on the edge of the hole and screw it on from the other side with the screw ring. The filler neck can be connected to the cooling circuit via a normal G1/4" female thread connection. After filling, the upper side should be sealed with a sealing plug. Technical Data: Material: Brass Colour: Carbon Black Thread: Inner G1/4" Thread Length: 15 mm
High-End CPU-Wasserkühler von aqua computer, vernickeltes Messing-Gehäuse, vernickelter Kupferboden, für AMD Sockel AM4/AM5, mit Thermal Grizzly Kryonaut Wärmeleitpaste
DEMCiflex Dust Filter 120mm Black/White DF0381Toote kirjeldus inglise keeles:Product description:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 120 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Firstly, it is easy to see if cleaning is necessary again - as soon as the white filter fabric has a gray haze, you should do this task. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside of the fan frame. If one of the two arrows points towards the interior, it is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Figure 4 shows an example configuration on a housing (not included). As can be seen, the use of LED fans is possible because the transparent material hardly hampers the lighting. Technical details:Size (frame): 128 x 128 mmSize (filter): 105 x 105 mmCompatibility: 120 mm fan slotMaterial (filter): polyester meshColor: black (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
The new Alphacool NexXxos radiators, a name that stands for experience and quality has come to bring a fresh breeze to the radiator market.This Radiator can discharge up to 1400 W at an ambient temperature of 30°C and fans with 4000 rpm.Every user of a water cooling system needs a radiator and everyone has different requirements towards the heat exchanger. Of course the customer always demands the best in its class. The Alphacool NexXxos radiators have come to compete with and to beat the best in their class and to be the best radiator in all sizes. No more endless choices without a clear class leader, the Alphacool NexXxos is the one tool for all your needs!Alphacool has been the company to introduce new developments and improvements in the radiator and water cooling sector generally many times over the last years.Following this tradition, the new NexXxos radiators are the first to truly deserve the “Full copper” attribute. All main parts, not only the fins and channels, but the chambers are also made from copper. This brings an improvement in performance where other radiators are left without a chance. The material already gives an advantage over the competition and the inner structure is up to par with the competition. Separated chambers give the coolant a clear direction, allowing high flow rates which improve the performance of the whole cooling loop.Flat chambers on the heat exchanger increase mounting flexibility thanks to the reduced overall length.Versatile and easy mounting is one of the main points, on which the research and development department at Alphacool focused. The chamber offers three possibilities for fitting installation on both inlet and outlet (not on the NexXos ST30). Less angled fittings are needed, improving flow rates and offering more mounting possibilities. Hence the radiator can even be installed in tight enclosures, where otherwise internal installation is not a possibility. A 1/4" screw plug allows easy de-aeration of the radiator (on all UT60 and NexXxos Monsta) and hassle-free vertical installation of the heat exchanger. The threaded opening can even be used for filling, e.g. in combination with a Fillport.Versatility is the essence of the new NexXxos series! The radiators are available in different versions to be used with 120mm, 140mm or 180mm fans and are available in different thicknesses. The choice of 30mm, 45mm and 60mm offers the perfect radiator for every purpose. Even mounting and installation of fans and radiator grills is easy and versatile with these radiators: The M3 threads are standard in the radiator sector and available in all lengths at an affordable price.Even the dreaded insertion of a screw too far into the radiator does not result in expensive damage. Unlike other radiators, the NexXxos series is equipped with an internal protective ledge which stops the screw before it damages the fins.Fin spacing is always an important factor in radiator design. The new series from Alphacool has a fin design which allows it to perform extremely well even with slow-spinning and medium-speed fans. This is not only pleasant thanks to the fact that it avoids unnecessary noise; it also means that the choice of fans that can be used with these radiators is not restricted.These radiators are the result of experience and powerful performance meeting future-oriented design and well-thought through solutions.Alphacool NexXxos radiators: The one tool for all your cooling needs! Technical DataDimensions (L x W x H)277 x 124 x 46mmQuantity of cooling channels24Cooling channelsCopperColorblackFan threadM3Connection6x G1/4"SlatsCopperNumber of fans2Thickness39 - 49mmFan size120mmHousingSteelManufacturerAlphacoolFins per inch12Pressure tested0,8 bar
EK Water Blocks EK-Torque STC-13/10 color ring pack of 10, red. These exchangeable rings for the 13 / 10mm soft tube compression fittings from EKWB are made of aluminum, are available in different colors and give your system a unique look. Compatibility: EK-Quantum Torque STC-13/10 connections Technical specifications: Red color Material: aluminum Quantity: 10 pieces
Schwarzes Wakü-Fitting von Phanteks mit zwei G1/4-Zoll-Gewinden (Male) zum Verbinden zweier GPU-Wasserkühler mit einem Abstand von 16 bis 22 Millimetern
240-mm-Radiator von Magicool, aus der G2-Ultra-Reihe mit 45 mm Dicke, für beidseitig 2x 120-mm-Lüfter, 13 FPI Lamellendichte für Silent-Fans, Dual-Pass-Design, Schwarz
When putting down, nothing beats smooth and easy. That is why we created the PK-2 thermal compound. The PK-2 thermal compound is a high performance thermal bonding agent specially designed for easy application.PK-2's core feature is its low viscosity, allowing for one to quickly and easily apply the thinnest coat of thermal compound possible.This will get your components up close and personal in no time.Soojusjuhtivus10,2 W/m·KKaal5 g
Toote kirjeldus inglise keeles:To connect the individual components of the water cooling, the choice of the correct connections and their sufficient number is essential. Otherwise, installation will quickly become a frustrating experience if assembly fails on the wrong or too few connectors and is delayed due to this. Bitspower offers a comprehensive product range that offers the right solution for every requirement - whether adapters, direct hose connections, brackets or distributors. The design is solid and has a sealing ring. Thus, the connections remain tight and ensure high long-term durability. This is a black glossy nickel plated, straight adapter with two G1 / 4-inch external threads. The special feature: The length of the adapter can be flexibly adjusted between 41 and 69 mm (measured without thread). For this purpose, only one nut is loosened, one side pulled out as desired and then fixed again with the union nut. Technical details:Material: brass, black nickel platedConnections: male thread: 2x G1 / 4 inchLength: 41 - 69 mm (variable)
EK-Quantum Magnitude Accent - Purple is an interchangeable inner aesthetic frame for EK's new Magnitude water block. This purple accent is best used on Magnitude water blocks with translucent tops where the LED’s shine inwards, or for those without LED implementation. This Magnitude accent is made of anodized aluminum. Available in several different colors and materials, these accent frames are compatible only with EK-Quantum Magnitude CPU water blocks Made in Europe - Slovenia!
Alphacools HardTube family does get an additional sibling. The new HardTubes made out of borosilicate glass certainly bring a new level of quality into every system. The previous method that has been most commonly used for water cooling systems is normal PVC hoses - now Alphacool introduces a new approach to water cooling. The Alphacool HardTube additionally brings more tidiness into the system which enables a further structured impression. Borosilicate glass ticks every box on the checking list for watercooling systems. Stability and a brilliant appearance are not the only qualities that should lead to chosing this glass as even most chemicals and temperature flactuations can not harm the borosilicate glass. The whole chemical industry is depending on this glass and we can certainly say that this is not without reason. All glass tubes are compatible with the Alphacool HardTube connectors. Alphacool currently offers two classical sizes. One tube with a 16mm outer diameter and another with 13mm outer diameter. Further different length with 90° angles are introduced as its not possible to personally deform these tubes. To cut the tubes for the preferred length Alphacool recommends using a diamand cutting disc for the Dremel®. (Additionally availaible in our product line: Diamant cutting disc - Art.No: 1012316 , Dremel® - Art.No: 32196 and 32229 ) The following options are available: HardTube borosilicate glass 13/10mm 90° 10/30cm and 20/40cm HardTube borosilicate glass 13/10mm 40cm and 60cm HardTube borosilicate glass 16/11mm 90° 10/30cm and 20/40cm HardTube borosilicate glass 16/11mm 40cm and 60cm Scope of delivery: 1x HardTube borosilicate glass 13/10mm 60cm WARNING: Do not under any circumstances use the usual glass tube cutter to shorten the borosilicate glass tube. Borosilicate glass is a solid glass which can not be cut properly with a normal glas tube cutter. Please refer to a Dremel® with the needed cutting disc. Note: Due to the made-to-fit pipes, the connections must be plugged straight with a little effort. Attention: This article is not compatible with Monsoon fittings. Der8auer: Extremely Expensive Hardtubes and DIY Glass-Cutter
EK-Quantum Vector FE RTX 3080 Backplate - Black is a CNC machined retention backplate made from black anodized aluminum for the EK-Quantum Vector FE RTX 3080 - Special Edition water block. The backplate covers the backside of the graphics card's PCB and serves as an aesthetic add-on. It provides additional passive cooling for the GPU core and rear of the printed circuit board VRM section. Due to the small size of both the card and the water block, the backplate boasts a ribbed design for additional passive cooling power. Enclosed EK-Quantum Vector FE RTX 3080 Backplate - Black Mounting screws Thermal pads
EK-Quantum Vector TRIO RTX 3080/3090 Active Backplate - Acetal ist eine hochmoderne Ergänzung der EK® Quantum Line. Sie ergänzt die bestehenden EK-Quantum Vector TRIO RTX 3080/3090 Wasserblöcke und kühlt aktiv die Rückseite aller MSI® TRIO und SUPRIM GeForce RTX™ 3080 und 3090 GPUs. Die EK-Quantum Vector TRIO RTX 3080/3090 Active Backplate wird mit einem neuen Anschluss geliefert, der den serienmäßigen Anschluss des Vector Wasserblocks ersetzt und den Wasserblock und die Vector Active Backplate zu einer Einheit verbindet. Auf diese Weise benötigt das gesamte Gehäuse nur einen Zu- und einen Abfluss, wodurch unnötige zusätzliche Schläuche entfallen und das Durcheinander reduziert wird. Es ist die ultimative ästhetische und leistungsfähige Lösung, bei der Ihre GPU zwischen zwei Wasserblöcken eingebettet ist, was eine maximale Kühlung ermöglicht. Technische Spezifikation: Abmessungen: (LxHxB) - 307x153x38mm Lieferumfang: EK-Quantum Vector TRIO RTX 3080/3090 Aktive Backplate - Acetal Erforderliche Befestigungsschrauben, Muttern und Unterlegscheiben 1x vernickelter Messingstecker G1/4" EK-Loop Multi Inbusschlüssel (6mm, 8mm, 9mm) Thermische Pads
Backplate mit aktiver Kühlung von EK Water Blocks, für EVGA XC3 RTX 3080 / 3080 Ti und 3090, vernickelter Kupferboden, Acetal-Deckel, adressierbare RGB-Beleuchtung
Backplate mit aktiver Kühlung von EK Water Blocks, für EVGA XC3 RTX 3080 / 3080 Ti und 3090, vernickelter Kupferboden, Acryl-Deckel, adressierbare RGB-Beleuchtung
The new Eiszapfen PRO hard tube fittings from Alphacool are the next step in development for the familiar Eiszapfen fittings. In the development of the fittings Alphacool concentrated on a specific problem, deforming PETG hard tubes at high temperatures. PETG can start to deform at 60°C. Although such a temperature is usually rarely reached, it can still occur. The Eiszapfen PRO fittings prevent this problem from the outset and hold the tubes in position. The deformation is prevented by the new nylon inserts inside and stabilizes the hard tubes. Furthermore, the fitting still has an O-ring and a compression seal. However, the contact area is much larger than with normal O-rings, which provides a better grip. With the insert and the compression seal, the tube is strengthened from the inside and outside. Even under heavy loads the HardTube does not slip. Alphacool has tested the tensile strength of up to over 8kg, so there is no need to worry about loose tubing. Technical details: Material: brass Colour: chrome Diameter: 22 mm Height: 20 mm Thread: G1/4" Thread length: 5 mm HardTube size: 13 mm Compatibility: PETG, acrylic, brass and glass tubes Weight: 0,023 kg Scope of supply: 1x Alphacool Eiszapfen PRO 13mm HardTube Fitting G1/4 - Chrome Notice: Attention: The manufacturer Mayhems advises that Mayhems fluids, especially the Aurora line of products, have been manufactured and distributed solely for show and modding purposes. These should not be utilized in the system for more than 14 days. We would also like to advise that Mayhems fluids can damage water cooling products, and using Mayhems fluids can thereby void the warranties offered by the following manufacturers: Koolance, Phobya, Alphacool, Aqua Computer, Watercool. Damages such as: clogging, corrosion of aluminium radiators, deterioration of glued containers, etc., are a consequence of the use of Mayhems, but will not be reimbursed by Mayhems. Use is therefore at one’s own risk.
