To connect the individual components of the water cooling, the choice of the correct connections and their sufficient number is essential. Otherwise, installation will quickly become a frustrating experience if assembly fails on the wrong or too few connectors and is delayed due to this. Bitspower offers a comprehensive product range that offers the right solution for every requirement - whether adapters, direct hose connections, brackets or distributors. The design is solid and has a sealing ring. Thus, the connections remain tight and ensure high long-term durability. This is a carbon black nickel plated, straight adapter with two 1/4 inch external threads. In addition, the connection is rotatable, which significantly simplifies the screwing. Note: The turning function of the connections should always be used in the disassembled state, as this is relatively stiff due to the design. When installed, do not apply force to connections to avoid damaging the connectors themselves and the radiators on them. Technical details:Material: brass, carbon black nickel platedConnections: male thread: 2x 1/4 inch
Water and electronics are not known to be compatible. To ensure that the separation between the two areas remains 100%, even with beloved water cooling, the sealing rings at the connections should be changed regularly. Although they have a long life, similar to vehicle tires, they lose their elasticity over time and become brittle. What leads to reduced grip on the road and provokes accidents in case of doubt, can also cause problems for the Wakü if a system becomes leaky. In addition to the contact of the water with the electronics, especially the sinking water pressure, the higher volume due to air inside the system and, in case of doubt, the total failure of the cooling are a considerable risk for the expensive hardware. With this set of many O-shaped sealing rings even extensive systems can be retreaded. The inner diameter requires use for G1 / 4 inch external thread. These are the most common thread standard, so that with few exceptions almost all screw threads can be sealed. Take care! Technical details:Material: rubberFor: G1 / 4 inch external threadContent: about 50 pieces
Toote kirjeldus inglise keeles:With the Crystal Link Tubes, Waku specialist Bitspower presents a very interesting solution for water enthusiasts who are not completely unskilled in their craft. These are solid tubes of acrylic plastic, which can be cut by the user to the required length and bent with the aid of a heat source suitable. The resulting possible connection of the individual water cooling parts with longer dead straight sections and exactly curved radii is a visually appealing alternative to the traditional connection by means of hoses dar. For example, if you use a hot air gun and the acrylic tube heated with it for some time, the material is so soft that one It can easily bend into the desired radius and holds as long until the acrylic has cooled and the now bent tube hardens again. It does not get any more individual Everything you need can be created here and even adjusted later. Ideally, in addition to a hot air gun and gloves you have a silicone rod (or something similar flexible, but heat-resistant) to hand, which one pushes into the tube in advance, so that the soft tube gets no kink when bending. The transparent-blue Crystal Link Tube offered here has an outer diameter of 12 mm and an inner diameter of 10 mm. The length is 100 cm. It can be used in conjunction with bit-power adapter fittings from the C47, C48 and ML series. Technical details:Material: acrylic glass (PMMA)Colour transparentOuter diameter: 12 mmInner diameter: 10 mmLength: 500 mmCompatibility: C47 Series Bit Power Fittings and Adapters C48 Bit Power Fittings and Adapters C48 Series Bit Power Fittings and Adapters
The Alphacool Eiswolf 120 GPX-Pro is the first prefilled water cooler for graphics cards with an integrated pump. Alphacool developed a completely new pump design to minimize the pump's volume and increase performance, and the suction pump was born. Through its suction principle, less turbulence is created in the water, allowing for a more even flow. This also makes the pump nearly inaudible - a first in the AIO market. Naturally, the cooler comes with a backplate that is directly attached to the cooler after installation, ensuring better heat transfer and distribution. This significantly improves the cooling performance. Additionally, it offers an aesthetic improvement in that the graphics card PCB is barely visible from the side. All that remains is a slight opening for the electrical connection and SLI/CrossFire Connector, of course. The hoses and connectors are also based on standard water cooling components. The hose is encased in anti-kink springs and comes in the 11/8mm size. The connectors have standard G1/4" threads and can therefore be exchanged for any other model or size desired. The two quick-release fasteners allow the cooler to fit easily into any cooling loop. If you are using the Alphacool Eisbaer CPU AIO water cooler, you can easily connect it with the Eiswolf 120 GPX-Pro using the quick-release fasteners. Using the Eisbaer gives you a redundant system, as you have two pumps in the loop. In the unlikely event that one pump fails, the other can still support the cooling loop. This is security at its highest level. Graphics card not included Compatibility MSI GeForce GTX 1080 Ti Armor 11G OC, 11GB GDDR5X, DVI, 2x HDMI, 2x DisplayPort (V360-010R) MSI GeForce GTX 1080 Ti Sea Hawk EK X 11GB GDDR5X (360-037R) MSI GeForce GTX 1080 Ti Gaming X 11G 11GB GDDR5X (V360-001R) MSI GeForce GTX 1080 Ti Gaming 11G 11GB GDDR5X MSI GeForce GTX 1080 Ti DUKE 11G OC 11GB GDDR5X MSI GeForce GTX 1080 Ti DUKE 11G 11GB GDDR5X MSI GeForce GTX 1080 Ti Armor 11G 11GB GDDR5X Scope of Delivery 1x Alphacool Eiswolf 120 GPX Pro Nvidia Geforce GTX 1080Ti M16 - black Configurator for VGA cooler Manual available for download here Compatibility list Nvidia Eiswolf Brochure
The EK-Loop Connect - USB External Cable 1m will allow the user to connect their EK-Loop Connect controller unit to the PC via a standard USB connector that can be found on the back of the motherboard. This type of connection is beneficial to modders because it allows them to pre-program the controller using another PC. This also makes it possible to run the pump, fan, and addressable RGB settings on another PC without the need to install an OS. This saves a great deal of time and still lets the user control D-RGB LED patterns for the needs of the video shoots, etc. Technical Specifications: Connectors: USB-A to 4-pin Length: 100cm
EK-Loop UNI Pump Reservoir Bracket - 140mm is a mounting adapter for installation of EK D5, DDC, SPC, and VTX pumps and pump-reservoir combo units to any 140mm fan mounting hole pattern (125mm hole spacing). Additionally, it can be used with EK-RES X3 Holder 60mm (2pcs) to mount any reservoir or pump-reservoir combo with a tube of 60mm in diameter. It can be used horizontally or vertically. The offset on the bracket allows for precise placement of the pump or reservoir according to your needs for clearance or easier tube routing. By turning the bracket around the offset can be moved left, right, back, or forward in a horizontal setup, and also left, right, up, or down in a vertical setup. Made from press-bent 1,5mm thick painted steel. The height of the bracket is 11.5mm. This product is compatible with the following EK products: Vertical: EK-Quantum Kinetic TBE D5 series Vertical: EK-XRES Revo D5 series Vertical: EK-XRES X3 series Horizontal: EK-XTOP DDC series Horizontal: EK-XRES SPC Classic series Horizontal: EK-Quantum Kinetic TBE DDC series Horizontal: EK-Quantum Kinetic TBE VTX series Horizontal and Vertical: EK-XTOP Revo D5 series Enclosed: EK-Loop UNI Pump Reservoir Bracket - 140mm 5x polyamide washer M4 0.8mm 5x screws M4x6 DIN7984 5x nut M4 Allen key 2.5mm
Statischer 45-Grad-Winkel-Adapter, Teil der EK-Quantum Torque-Serie, zur Verbindung von G1/4-Zoll-Außen- mit G1/4-Zoll-Innengewinden, aus vernickeltem und satiniertem Messing
