S+31DLC10D is a 10G SFP+ transceiver with a LC connector, 1310nm, for up to 10 kilometer Single Mode fiber connections.Units are tested and compatible with CCR1036-8G-2S+ and CCR1036-8G-2S+EM. Units are compatible with non-MikroTik SFP devices as well.
UFP-VIEWPORTThe UniFi Protect ViewPort allows you to view your UniFi Protect camera feeds on an HDMI display. It uses Power over Ethernet and connects to the local network hosting your cameras and connects via HDMI to a display. The UniFi Protect ViewPort offers 4K video output at 30 frames per second. Protect systems can be viewed in custom high-density camera matrix configurations.
8-Port 10/100/1,000 Mbps Desktop Switch Eight 10/100/1,000 Mbps auto-negotiation RJ45 ports with auto MDI / MDIX supported Easily wired network expansion Compact design for flexible arrangement Plug and play setup, no configuration required Green Ethernet technology saves power by up to 82%
This table microphone by Delock is suitable for use in conferences. Optimal recordings The microphone has a circle pattern (omnidirectional) and therefore captures the acoustic signal ideally. Due to a high power, low self-noise and precise performance, even the finest sounds are optimally recorded. Touch mute button & status LED The touch mute button quickly mutes the microphone. The LED is red when muted and green when recording. Headphone output The microphone has a 3.5 mm stereo jack output for connecting headphones or speakers. Plug & Play Due to USB Plug & Play the microphone is ready to use immediately, no driver installation is needed. The microphone works with all common operating systems such as Windows, Mac OS, Chrome OS and Linux. Specification • Connectors: 1 x USB 2.0 Type-A male 1 x 3.5 mm 3 pin stereo jack female • Directivity: omnidirectional • Sensitivity: -16 dB +/- 3 dB • Frequency range: 100 Hz - 10 kHz • Sample rate: 16 Bit / 44.1 kHz • Signal-to-noise ratio (SNR): ca. 65 dB • Mute-Button • Status LED • Cable length: ca. 1.5 m • Colour: black • Dimensions (Ø x H): ca. 75 x 19 mm • USB bus powered • Plug & Play System requirements • Chrome OS • Linux Kernel 4.4 or above • Mac OS 10.9 or above • Windows 7/7-64/8.1/8.1-64/10/10-64 • PC or laptop with a free USB Type-A port Package content • USB microphone • User manual
Discover the reliability and performance of the Ubiquiti UniFi network cable, a vital component for any modern network setup. This CAT 6 patch cable features male RJ-45 connectors on both ends, ensuring a secure and efficient connection between your devices. With compliance to TIA/EIA-568-B.2 standards, it delivers dependable network performance. Additionally, its VW-1 (UL1581) certification attests to its safety and durability, making it an ideal choice for indoor environments. Whether for home or office use, this network cable is designed to meet the demands of your networking needs, providing a stable and high-speed data transmission solution.
Ubiquiti UVC-G5-Dome-Ultra on kompaktne ja vastupidav IP-kaamera, mis on loodud kõrgekvaliteediliseks turvaseireks. Selle mõõtmed on Ø63.6 x 68.2 mm ja kaal 175 g, ning see on valmistatud alumiiniumisulamist ja polükarbonaadist, pakkudes tugevat kaitset. IK06 vastupidavusklass tagab parema löögikindluse, muutes kaamera sobivaks sise- ja poolvälitingimustes kasutamiseks.Kaamera on varustatud 1/2.4" CMOS sensoriga ja fikseeritud fookuskaugusega objektiiviga, pakkudes laia vaatevälja: 102.4° horisontaalset, 54.9° vertikaalset ja 120.6° diagonaalset katvust. Öine nägemine on toetatud sisseehitatud IR-LED valgustuse ja IR-lõikurfiltriga, mis võimaldab vaadata kuni 20 meetri kaugusele täielikus pimeduses.UVC-G5-Dome-Ultra salvestab videot 4MP eraldusvõimega (2688 x 1512) ja maksimaalse kaadrisagedusega 30 FPS, pakkudes selgeid ja detailseid pilte. Seadmel on täiustatud pildiseaded, sealhulgas värvi, heleduse, teravuse, kontrasti, valgetasakaalu ja särituse juhtimine, ning müra vähendamise funktsioonid 2DNR ja 3DNR.Kaamerat juhib kahe tuumaga Arm® Cortex®-A7 protsessor, ning see kasutab toite ja andmeedastuse jaoks PoE-d, maksimaalse energiatarbega 4.2W. Kaamera on mõeldud pindpaigalduseks ja on varustatud 10/100 MbE RJ45 võrguühendusega.Kaamera töötab temperatuurivahemikus -20 kuni 40º C ja niiskusesisaldusega 10 kuni 90%, olles FCC, IC ja CE sertifikaatidega kooskõlas. UVC-G5-Dome-Ultra ühildub sujuvalt UniFi Protect veebirakenduse ja iOS™ ning Android™ mobiilirakendustega, pakkudes lihtsat juhtimist ja monitooringut.
The Ubiquiti UniFi Device Bridge Pro is designed to provide robust wireless connectivity in various environments. With an antenna gain level of 19 dBi and support for advanced wireless protocols like IEEE 802.11a/n/ac, this device ensures strong signal transmission over long distances. It has a range of up to 5 km in open space, suitable for applications where network extension is essential.This device is built to withstand extreme conditions, operating in temperatures from -40°C to 60°C and humidity levels between 5% to 95%. The weatherproof, UV-resistant casing protects the internal components, making it a reliable option for outdoor installations. Equipped with Power over Ethernet (PoE) capabilities and efficient performance reaching up to 867 Mbps on the 5 GHz band, the Ubiquiti UniFi Device Bridge Pro is an effective solution for establishing a resilient wireless bridge.
Long-range outdoor CPEs with modern Wi-Fi 6 performance, rugged design, and unbeatable pricing. Available in two models (24.5 or 27 dBi), they’re ideal for point-to-point links over great distances. This is the 24.5 dBi version. Need a fast, stable connection across large distances? Whether you’re bridging two buildings, connecting a remote site, or sharing your internet with nearby infrastructure — the new LHG Wi-Fi 6 series is built for the challenge. And here’s the best part: we’ve kept the same pricing as the previous generation. High performance, long range, and Wi-Fi 6 — all without breaking the budget. The 802.11ax standard brings crucial improvements for long-distance wireless links — including better spectral efficiency, higher modulation rates (1024-QAM), and lower latency. That means stronger performance even in noisy environments and faster, more stable connections over a greater distance. Combined with WPA3 encryption and RouterOS v7, the LHG ax series is ready for the challenges of modern outdoor networking. Order yours today — and be ready too! LHG 5 ax is compact, long-range CPE with a 24.5 dBi antenna. Perfect for links up to 20 km in most scenarios. Check related devices below for the XL version if you need a longer distance!
Mikrotik Chateau LTE7 (5HACD2HNDTC&R11E-LTE7) | Dual-band (2.4 GHz / 5 GHz) | Wi-Fi 5 (802.11ac) | WLAN data transfer rate (max) 1167 Mbit/s | Ethernet WAN Yes | SIM card slot Yes | 3G/4G USB modem compatibility Yes | Ethernet LAN Yes | Ethernet LAN interface type Gigabit Ethernet | Mobile network generation 4G | 1xEthernet LAN (RJ-45) ports | USB port Yes | Antenna design Internal | Power source type DC | Operating temperature (T-T) -40 - 70 C
SWITCH LANBERG ILFE-4P-1GE-1S-90 POE 1XBT 3XAT SFP/ETH DIN UNMANAGMENT FAST ETHERNETLightweight unmanaged industrial switch Lanberg ILFE-4P-1GE-1S-90 Industrial switches are an essential active device in any network structure - from automation and SCADA systems, through cable TV networks, to distributed IoT installations and surveillance. Lanbergs lightweight industrial switch series was designed for demanding working environments: a metal enclosure, passive cooling, and operating parameters that support stable operation across a wide ambient temperature range. The key advantages of this line include high PoE power (PoE+ / PoE++), redundant power input (you can connect 2 power sources), DIN-rail mounting, VLAN and EXTEND functions, automatic MDI/MDI-X, flow control, an intelligent PoE port cut-off function, and MAC auto-learning.In practice, this is a network switch built for distributed infrastructure: industry, street lighting infrastructure, outdoor CCTV monitoring, alarm systems, and both indoor and outdoor deployments where Ethernet data transmission and PoE power for end devices (cameras, recorders, access points, controllers, sensors) matter - often with higher power requirements.NOTE: The device power supply is included in the product set.Industrial switch ILFE-4P-1GE-1S-90 with a rich selection of portsThis switch is equipped with a port set optimized for CCTV/IoT installations: 4 x Fast Ethernet RJ45 PoE ports (10/100 Mb/s): 1× IEEE 802.3bt PoE++ (up to 90 W) + 3× IEEE 802.3af/802.3at PoE+. 1 x 1000BASE-T uplink (Gigabit Ethernet) - for traffic aggregation and connection to the network core / NVR / router. 1 x SFP slot (1000BASE-X) as a fiber uplink - optical parameters depend on the selected SFP module. Lanberg Gigabit Ethernet switches with PoE++ technologyPoE, PoE+ and PoE++ technology makes it possible to deliver both data and power to devices using a single Ethernet cable, without additional electrical infrastructure at the camera or access point. The technology based on 802.3af, 802.3at and 802.3bt standards allows powering peripheral devices with up to 120 W (90 W or 120 W depending on the model). A major benefit of the enhanced PoE standard is also high link quality and fast data transmission (up to 1 Gbps, depending on the model). Thanks to these capabilities, PoE is widely used in extensive surveillance networks. PoE+ and PoE++ enable real-time 4K camera streams while maintaining smooth performance.VLAN and EXTEND functionsVLAN helps with logical traffic separation (e.g., CCTV vs the rest of the network), improving order and limiting unwanted broadcast traffic. EXTEND mode was introduced for deployments where you need to ensure operation over a longer run - at the cost of speed. In practice, EXTEND can extend transmission and PoE powering up to 250 m on a single cable run (extend 250 m) in typical surveillance and distributed infrastructure deployments.An unmanaged switch that knows how to disconnect devicesIf too many devices are connected and the available PoE power reserve is exceeded, the switch will disconnect endpoints starting from the highest-numbered PoE ports down to the lowest until a safe power limit is restored. This makes it easy to plan for power spikes and define which devices are most critical and should stay online first.Intelligent switches with SFP module supportLanbergs lightweight industrial switches support different fiber types thanks to an integrated SFP slot. Optical transmission parameters depend on the selected SFP module. The switch also supports automatic MDI/MDIX, so crossover cables are not required, and it automatically detects and sets link speed and transmission mode.Unmanaged PoE switch with redundant power inputRedundant power input means a dual power feed to the switch (two independent power paths). If one source fails, the device automatically switches to the other - without user intervention. This solution provides higher security and network stability.Easy installation in 19" racks and on a DIN railInstallation is fast and hassle-free thanks to Plug & Play operation. MDI/MDIX auto-detection recognizes the cable type, eliminating the need for crossover wiring and automatically setting link speed and transmission mode. Reliable packet forwarding with CRC checking (store-and-forward) is essential in IP surveillance systems. A major advantage is DIN-rail mounting, which gives flexible installation options both inside RACK cabinets and outside them.Metal enclosure for durability and wide operating temperature rangeA robust metal enclosure improves durability and supports stable continuous operation. The recommended ambient operating range is -25 to 65°C, with 10-90% humidity. While the enclosure is not water- or dust-tight, installed inside an appropriate outdoor/industrial housing it will perform very well in demanding indoor and outdoor environments such as factories, production plants, and industrial halls.
D-Link G536 5G NR BE3600 Wi-Fi 7: a modern router that allows you to share a fast 5G or 4G/LTE cellular connection with wired and wireless devices. Just insert a Nano SIM card to create a home or business network without the need to install a permanent cable connection. The router can also use a wired WAN connection and automatically switch between mobile Internet and Ethernet in the event of a primary link failure. The 5G NR modem provides theoretical download speeds of up to 4.67 Gb/s and upload speeds of up to 1.25 Gb/s in SA mode. If there is no 5G coverage, the device can automatically use the 4G/LTE network, offering download speeds of up to 1.6 Gb/s. Two cellular antennas can be replaced with optional external antennas connected to SMA connectors, which allows you to improve signal quality in rooms with weaker coverage. The dual-band Wi-Fi 7 BE3600 network reaches total speeds of up to 3,600 Mb/s: up to 2,882 Mb/s in the 5 GHz band and up to 688 Mb/s in the 2.4 GHz band. Multi-Link Operation and 4K-QAM technologies improve bandwidth utilization, reduce latency and increase connection stability when streaming, gaming, video conferencing and working with multiple devices. The router can support up to 128 devices simultaneously. Two 2.5 Gb/s Ethernet ports allow you to connect computers, switches, NAS servers and other devices that require a fast wired connection. One of the ports can function as WAN or LAN, providing flexible network configuration and the ability to use a wired backup connection. The network can be configured and controlled using the D-Link FALCON application for Android and iOS devices or through the browser-based administration panel. The router supports WPA3 encryption, guest network, parental controls, SPI firewall, IP address filtering and DMZ function. Compatible with select D-Link Wi-Fi Mesh devices to extend your wireless coverage. Device type 5G NR Router with Wi-Fi 7 Manufacturer number G536/E D-Link G536 model Cellular network standard 5G NR, 4G LTE and 3G 5G SA and NSA modes Maximum 5G SA download speed Up to 4.67 Gb/s 5G SA maximum upload speed Up to 1.25 Gb/s 5G NSA maximum download speed Up to 4.67 Gb/s 5G NSA maximum upload speed Up to 836 Mb/s LTE maximum download speed Up to 1.6 Gb/s Maximum upload speed LTE Up to 211 Mbps SIM card type Nano SIM, 4FF format Number of SIM slots 1 Wi-Fi standard Wi-Fi 7, IEEE 802.11be Supported Wi-Fi standards IEEE 802.11be, 802.11ax, 802.11ac, 802.11n, 802.11g, 802.11b and 802.11a Wi-Fi Class BE3600 2.4 GHz and 5 GHz Wi-Fi bands Maximum combined Wi-Fi speed 3600 Mbps Maximum speed on the 5 GHz band 2882 Mbps Maximum speed on the band 2.4 GHz 688 Mb/s Multi-Link Operation Yes 4K-QAM Yes Maximum number of connected devices 128 Ethernet ports 1x 2.5GbE WAN/LAN and 1x 2.5GbE LAN Automatic link switching Yes, between cellular and Ethernet WAN Number of cellular antennas 8 internal External antenna connectors 2x SMA Number of Wi-Fi antennas 5 internal D-Link Wi-Fi Mesh Supported with selected devices Wi-Fi WPA, WPA2 and WPA3 encryption WPS fast connection Stateful Packet Inspection firewall Spoofing protection Anti-spoofing IP address filtering Yes DMZ Yes Guest network Yes Parental controls Yes Management D-Link FALCON application and browser-based administration panel Supported application systems Android and iOS Power, WPS and Reset buttons LED indicator Power, device status and WPS 12 V power supply / 2 A Operating temperature From 0°C to 40°C Operating humidity From 10% to 90%, non-condensing Dimensions 137 x 146 x 205 mm Weight 684 g Color White
This robust industrial router is equipped with 4 x Gigabit Ethernet ports, Quad-core CPU and 256 MB of RAM. These powerful specifications combined with core RutOS software features such as advanced Firewall and RMS support makes this device a superb Industrial performer where no Cellular or WiFi connectivity is required.ETHERNETWAN1 x WAN (can be configured to LAN) 10/100/1000 Mbps, comply IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossoverLAN3 x LAN ports, 10/100/1000 Mbps, comply IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossoverNETWORKRoutingStatic routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2)Network protocolsTCP, UDP, IPv4, IPv6, ICMP, UDP, NTP, DNS, HTTP, FTP, SMTP, TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPPVoIP passthrough supportH.232 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packetsConnection monitoringPing Reboot, Periodic Reboot, LCP and ICMP for link inspectionFirewallPort forward, traffic rules, custom rulesDHCPStatic and dynamic IP allocation, DHCP RelaydQoSTraffic priority queuing by source/destination, service, protocol or port, WMM, 802.11eDDNSSupported >25 service providers, others can be configured manuallyNetwork backupVRRPSSHFS (optional)Possibility to mount remote file system via SSH protocol (not available in standard FW)MONITORING & MANAGEMENTWEB UIHTTP, status, configuration, FW update, CLI ,troubleshoot, event log, system log, kernel logFOTAFirmware update from server, automatic notification.SSHSSH (v1, v2)TR-069OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVsystemsSNMPSNMP (v1, v2, v3), SNMP trapJSON-RPCManagement API over HTTPMODBUSMODBUS TCP status/controlRMSTeltonika Remote Management System (RMS)SYSTEM CHARACTERISTICSCPUQuad-core ARM Cortex A7, 717MHzRAM256MB, DDR2FLASH memory256MB SPI FlashFIRMWARE / CONFIGURATIONWEB UIUpdate FW from file, check FW on server, configuration profiles, configuration backupFOTAUpdate FW/configuration from serverRMSUpdate FW/configuration for multiple devicesKeep settingsUpdate FW without losing current configurationFIRMWARE CUSTOMIZATIONOperating systemRutOS (OpenWrt based Linux OS)Supported languagesBusybox shell, Lua, C, C++Development toolsSDK package with built environment providedINPUT/OUTPUTInput1 x Digital Input (Non-isolated, Logic low 0...+5V, Logic high +8...+40V)Output1 x Digital Output (open collector type, 30V@0.3A)EventsEMAIL, RMSUSBData rateUSB 2.0ApplicationsSamba share, custom scriptsExternal devicesPossibility to connect external HDD, flash drive, additional modem, printerStorage formatsFAT, FAT32, NTFSPOWERConnector4 pin industrial DC power socketInput voltage range9 - 50 VDC, reverse polarity protection, voltage surge/transient protectionPoE (passive)Passive PoE. Possibility to power up through LAN port, not compatible with IEEE802.3af and 802.3at standardsPower consumption11W Max.PHYSICAL INTERFACES (PORTS, LEDS, BUTTONS)Ethernet4 x RJ45 ports, 10/100/1000 MbpsStatus LEDs3 x connection status LEDs, 5x connection strength LEDs, 8x LAN status LEDs, 3x WAN status LEDs, 1x Power LEDPower4 pin industrial DC power socketUSBUSB A socket for external devicesResetReset/restore to default buttonPHYSICAL SPECIFICATIONCasing materialFull aluminium housingDimensions115 mm x 95 mm x 32 mm (H x W x D)Weight357 gMounting optionsDIN rail (can be mounted on two sides), flat surface placementOPERATING ENVIRONMENTOperating temperature-40 C to 75 COperating humidity10% to 90% non-condensingIngress Protection RatingIP30
Antenna kit for LoRa® with a 6.5 dBi Omni antenna for 824-960 MHz 1 m long SMA cable and mechanical holder for quick and easy mast attachment.The new kit offers significantly higher durability in a smaller package – without sacrificing performance. The improved cable durability and the added IP66 water resistance with protection against powerful jets make this kit an excellent choice for all kinds of marine and coastal projects.Mount this antenna on a 25-50 mm mast or on the wall and enjoy the superb coverage!
Type Adapter | Data transmission speed 2402 Mbps | Wi-Fi 6 | USB 3.0 | Antenna Type Omni-Directional | Wireless Transmit Power 15 dBm | Wireless Frequency Range 2.4 GHz and 5GHz
